2020 HYUNDAI I10 air conditioning

5-63
05
Automatic heating and air con-
ditioning
OAI3059110I
1. Press the AUTO button.
The modes, fan speeds, air intake
and air-conditioning will be controlled
automatically according to the tem-
perature setting you select.
OAI3059111I
2. Turn the temperature control knob
to set the desired temperature. If
the temperature is set to the lowest
setting (Lo), the air conditioning
system will operate continuously.

5-64
Convenient features
Manual heating and air condi-
tioning
The heating and cooling system can
be controlled manually by pushing
buttons other than the AUTO button.
In this case, the system works
sequentially according to the order of
buttons selected. When pressing any
EXWWRQH[FHSWWKH$872EXWWRQZKLOVW
using automatic operation, the func-
tions not selected will be controlled
automatically.
1. Start the engine.
2. Set the mode to the desired posi-
tion.
To improve the effectiveness of
heating and cooling, select the
mode according to the following:
- Heating :
- Cooling :
Mode selection
OAC3059100R
3. Set the temperature control to the
desired position.
4. Set the air intake control to fresh
mode.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn
the air conditioning system on.
7. Press the AUTO button in order to
convert to full automatic control of
the system.

5-66
Convenient features
Temperature control
OAI3059111I
The temperature will increase by
turning the knob to the right.
The temperature will decrease by
turning the knob to the left.
The temperature will increase or
decrease by 0.5°C (1°F) for each
incremental location. When set to the
lowest temperature setting, the air
conditioning will operate continuously.
7emperature conversion
If the battery has been discharged or
disconnected, the temperature mode
display will reset to Centigrade.
To change the temperature unit from
°C to °F or °F to °C :
- Automatic climate control system
Press the AUTO button for 3 sec-
onds whilst pressing the OFF but-
ton.
- Instrument cluster
Go to User Settings o Other
Features o Temperature Unit.
The temperature unit on both the
cluster LCD display and the climate
control screen will change.
Air intake control
OAI3059106I
This is used to select the outside
(fresh) air position or recirculated air
position.
To change the air intake control posi-
tion, push the control button.
Recirculated air position
With the recirculated air
position selected, air
from the passenger
compartment will be
drawn through the heat-
ing system and heated
or cooled according to
the function selected.
2utside (fresh) air position
With the outside (fresh)
air position selected, air
enters the vehicle from
outside and is heated or
cooled according to the
function selected.

5-68
Convenient features
Air conditioning
OAI3059107I
3XVKWKH$&EXWWRQWRPDQXDOO\WXUQ
the air conditioning system on (indi-
cator light will illuminate).
Push the button again to turn the air
conditioning system off.
OFF mode
OAI3059116I
Push the OFF button of the front to
turn off the air climate control system.
However, you can still operate the
mode and air intake buttons as long
as the ignition switch is in the ON
position.
System operation
Ventilation
1. Select the Face Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
Heating
1. Select the Floor Level mode.
2. Set the air intake control to fresh
mode.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
5. If desired, turn the air conditioning
ON with the temperature control
knob set to heat in order to dehu-
midify the air before it enters into
the cabin.
If the windscreen fogs up, select the
Floor & Defrost
mode or press
the Front Defrost
mode.

5-70
Convenient features
Air conditioning system operation
tips

5-71
05
i Information
‡ Replace the filter according to the
0aintenance Schedule.
If the car is being driven in severe
conditions such as dusty, rough
roads, more frequent climate control
air filter inspections and changes are
required.
‡ When the air flow rate suddenly
decreases, we recommend that the
system be checked by a +<81'AI
authorised repairer.
Checking the amount of air con-
ditioner refrigerant and com-
pressor lubricant
When the amount of refrigerant is
low, the performance of the air condi-
tioning is reduced. Overfilling also
has a bad influence on the air condi-
tioning system.
Therefore, if abnormal operation is
found, we recommend that the sys-
tem be inspected by a HYUNDAI
authorised repairer.
NOTICE
It is important that the correct type
and amount of oil and refrigerant
is used. Otherwise, damage to the
compressor and abnormal system
operation may occur. To prevent
damage, the air conditioning sys-
tem in your vehicle should only be
serviced by trained and certified
technicians.
WARNING
Vehicles equipped with R-134a
Since the refrigerant is
operated at very high
pressure, the air condi-
tioning system should
only be serviced by
trained and certified technicians.
All refrigerants should be
reclaimed with proper equipment.
Venting refrigerants directly to the
atmosphere is harmful to individu-
DOV DQG HQYLURQPHQW )DLOXUH WR
heed these warnings can lead to
serious injuries.
WARNING
Vehicles equipped with R-1234yf
Since the refrigerant is
mildly flammable and
operated at high pres-
sure, the air condition-
ing system should only
be serviced by trained
and certified techni-
cians. It is important that
the correct type and
amount of oil and refrigerant are
used.
All refrigerants should be
reclaimed with proper equipment.
Venting refrigerants directly to the
atmosphere is harmful to individu-
DOV DQG HQYLURQPHQW )DLOXUH WR
heed these warnings can lead to
serious injuries.

5-72
Convenient features
OAC3019020TU
Air Conditioning refrigerant label
(if equipped)
You can find out which air condition-
ing refrigerant is applied to your vehi-
cle on the label located inside of the
bonnet.


5-74
Convenient features
Automatic climate control
system
To defog inside windscreen
OAI3059108I
1. Select desired fan speed.
2. Select desired temperature.
3. Press the defroster button (
).
4. The air-conditioning will turn on
according to the detected ambient
temperature, outside (fresh) and
higher fan speed will be selected
automatically.
If the air-conditioning, outside (fresh)
air position and higher fan speed are
QRWVHOHFWHGDXWRPDWLFDOO\DGMXVWWKH
corresponding button or knob manu-
ally.
If the
position is selected, lower
IDQ VSHHG LV DGMXVWHG WR KLJKHU IDQ
speed.
To defrost outside windscreen
OAI3059109I
1. Set the fan speed to the highest
position.
6HWWKHWHPSHUDWXUHWRWKHH[WUHPH
hot (HI) position.
3. Press the defroster button (
).
4. The air-conditioning will turn on
according to the detected ambient
temperature and outside (fresh)
mode will be selected automatical-
ly.
If the position is selected, lower fan
VSHHGLVDGMXVWHGWRKLJKHUIDQVSHHG