2020 DODGE DURANGO inflation pressure

DON’T MIX TIRES OF DIFFERENT SIZES AND TYPES ON THE
SAME AXLE
For optimum handling and control, Goodyear recommends fitment of
four (4) tires of the same type and size unless otherwise specified by the
vehicle manufacturer.
WARNING!
Before you replace your tires, always consult the vehicle owner ’s
manual and follow the vehicle manufacturer ’s replacement tire
recommendations. Vehicle handling may be significantly affected
by a change in tire size or type. When selecting tires that are
different from the Original Equipment size, see a professional
installer in order to make certain that proper clearance, load-
carrying capacity and inflation pressure are selected. Never exceed
the maximum load capacity and inflation pressure listed on the
sidewall of the tire. Always drive safely and obey all traffic laws.
Avoid sudden, sharp turns or aggressive lane changes. Failure to
follow this warning may result in loss of control of the vehicle,
leading to an accident and serious injury or death.
When replacing tires, you must maintain the outside diameter and
load-carrying capacity of the Original Equipment tire. Inflation pressure
may need to be adjusted to avoid overloading the tire. Consult the Tire &
Rim Association Load and Inflation Tables, ETRTO or JATMA standards
for correct load and inflation information.
NEVER FIT TIRES TO A VEHICLE THAT HAVE LESS LOAD-
CARRYING CAPACITY THAN REQUIRED BY THE ORIGINAL
EQUIPMENT MANUFACTURER
Examples: Many vehicles, such as large passenger vans, require Load
Range E tires as designated by the vehicle manufacturer. Fitment of a tire,
such as a Load Range D, with less carrying capacity is not allowed. In
other cases, tires of the same size may carry different load indexes in the
service description. You must make certain the replacement tires fitted to
the vehicle have a load-carrying capacity equal to or greater than what
the Original Equipment manufacturer specifies.
GOODYEAR DUNLOP TIRES
132

TIRE SERVICE LIFE
Tires are designed and built to provide many thousands of miles of
excellent service. For maximum benefit, tires must be maintained prop-
erly to avoid tire damage that may result in removal from service before
the tread is worn down to minimum depth.
It is not practical to accurately predict the service life of any specific tire
in chronological time since service conditions vary widely. The service-
ability of a tire over time is a function of the storage and service
conditions (inflation pressure, load, speed, road hazard injury, etc.) to
which a tire is subjected. Consumers should not rely solely on the
appearance of the tire, but should be aware of any change in dynamic
performance such as increased air loss, noise or vibration, which could be
a sign to remove the tire. Therefore, it is essential to have tires, including
spares, inspected regularly (at least monthly) for proper inflation pres-
sure, damage and treadwear.
Check your vehicle’s owner ’s manual (or your vehicle) to determine if
it is equipped with run-flat (extended mobility) tires. If your vehicle is
equipped with run-flat tires, the following applies:
GOODYEARDUNLOPTIRE6
HOWTOREAD A TIRE D.O.T. SERIAL NUMBER
D.O.T.
stands
for
Department
of
Transportation
and
the
number
is
on
the

lower
sidewall
of
each
tire
to
show
that
the
tire
meets
or
exceeds
the

Department
of
Transportation
safety
standards.
134

RUN-FLAT TECHNOLOGY EXTENDED MOBILITY TECHNOLOGY
(EMT™), RUNONFLAT® (ROF) AND DUNLOP SELFSUPPORTING
TECHNOLOGY (DSST®) ORIGINAL EQUIPMENT TIRES
IMPORTANT SAFETY INFORMATION
OPERATIONAL MONITORING
The information contained in this Limited Warranty Brochure applies
only to the Original Equipment tires supplied with your vehicle. In order
for Goodyear Run-Flat (Extended Mobility Technology [EMT], RunOn-
Flat [ROF]) or Dunlop Run-Flat (Dunlop Self- Supporting Technology
[DSST]) tires to obtain the performance criteria stated within this Limited
Warranty, Goodyear or Dunlop Run-Flat tires must use specific parts,
such as a low tire pressure monitoring system authorized by the Original
Equipment vehicle manufacturer.
RUN-FLAT TIRE FEATURE:
The Goodyear or Dunlop Run-Flat tire is a high-performance tire with a
remarkable feature: It can operate for limited distances with very low or
even no inflation pressure (refer to your Vehicle Owner ’s Manual for
these limitations). This is an important benefit, especially if inflation loss
occurs at a location where immediately stopping your vehicle could be
hazardous. TIRE PRESSURE MONITORING SYSTEM ALERT Refer to
your vehicle Owner ’s Manual for more information on what to do if the
tire pressure warning system activates.
WARNING!
If the tire pressure-monitoring system signals an alert, follow these
safety precautions to prevent a loss of vehicle control that could
result in serious personal injury or death:
•Slow your speed. Do not exceed 50 mph (80 kph).
• Avoid hard cornering, hard braking and severe handling maneu-
vers.
• Avoid potholes and other road hazards.
Remember that when your tires have lost air pressure, your vehicle’s
handling capability is reduced, particularly during severe
maneuvers.
GOODYEAR DUNLOP TIRES
135

WARNING!
Because of the unique characteristics of Run-Flat tires, the wheels
on which they are mounted and your vehicle’s tire pressure
monitoring system, all tire service work other than routine inflation
maintenance and external inspections must be performed by service
personnel at a Goodyear or Dunlop Run-Flat service facility.
Do not attempt to mount or demount Run-Flat tires yourself; serious
injury or death could result. Only specially trained persons should
mount, demount and repair Run-Flat tires, and more than 40 psi
(270 kPa) may be required to seat beads. A safety cage and clip-on
extension air hose must be used if more than 40 psi (270 kPa) is need
to seat beads.
GOODYEARDUNLOPTIRES
TOPROLONG TIRELIFEDURING A SYSTEM ALERT
The
Goodyear
or
Dunlop
Run-Flat
tire
can
be
driven
at
low
or
zero
air

pressure
(refer
to
your
vehicle
Owner ’s
Manual
for
these
limitations).
To

help
prolong
the
life
of
a
tire
operating
under
low-inflation
conditions,

drive
at
a
speed
as
far
below
50
mph
(80
kph)
as
possible.
Also,
drive
the

shortest
distance
possible
before
obtaining
tire


service.
Taking
these

precautions
will
increase
the
chance
that
your
tire
will
be
repairable.
SERVICE AFTERA SYSTEM ALERT
To
obtain
service
after
operating
under
low-inflation
conditions,
contact

your
Goodyear
or
Dunlop
Run-Flat
service
facility.
Trained
service

personnel
will
inspect
your
tires
to
determine
if
they
are
in
need
of
repair

or
replacement.
To
locate
the
nearest
authorized
Goodyear
or
Dunlop

Run-Flat
service
facility,
call
1-800-
GOODYEAR
1-800-466-3932
.
TIREREPAIR
Like
any
other
Goodyear
or
Dunlop
speed-rated,
high-performance
tire,

the
Goodyear
or
Dunlop
Run-Flat
tire
may
be
repaired
to
correct
a

puncture
in
the
tread,
but
PROPER
MATERIALS
AND
PROCEDURES

MUST
BE
USED.
Contact
a
Goodyear
or
Dunlop
Run-Flat
service
facility

for
information
on
proper
repairs.
For
the
location
of
the
nearest
facility,

call
1-800-GOODYEAR
1-800-466-3932


.
136

and beads. Do not exceed the maximum recommended pressure to
seat beads on rim. Use remote control inflation equipment and
inflation cage.
NOTE:
• Never inflate over 40 psi to seat beads.
• Mount radial ply tires only on rims designated by wheel manufacturer
as suitable for radial tire.
• Only specially trained persons shall mount tires.
• AIR PRESSURE
Check the pressure in your tires, including your spare, at least
monthly, and always before and during extended driving. Check tires
cold (at least 3 hours after the vehicle has been stopped and before it
is driven more than 1.6 kilometers or 1 mile). Do not reduce pressure
when tires are hot, use an accurate air pressure gauge to check
pressure and maintain it at the level recommended on the vehicle tire
placard or in the Owner ’s Manual. Under inflation produces extreme
flexing of sidewalls and builds up heat to the point that premature tire
failure may occur. Over inflation can cause the tires to be more
susceptible to impact damage. Cold tire pressures, however, should
never be higher than the limit molded on the sidewall.
• LOAD LIMITS
Never exceed the load-carrying limits molded onto the sidewall of
your tires or the maximum vehicle load limit as shown on the vehicle
tire placard, whichever is less. Overloading builds up excessive heat in
the tire and leads to early and/or sudden failure.
• HAZARDS
Avoid running over objects (e.g., chuckholes, rocks, curbs, metal, glass,
etc.) which may possibly cause internal tire damage. Continued use of
a tire that has suffered internal damage (which may not be externally
visible) can lead to dangerous tire failure. Determination of suspected
internal damage requires demounting the tire from its rim and
examination by trained tire personnel.
HANKOOK TIRES
142

•ADDITIONAL SAFETY INFORMATION FOR TEMPORARY TIRE
– Air pressure.
Check inflation pressure as soon as practical after installation and
inflate to 60 psi. The tire pressure should be checked monthly and
maintained at 60 psi while the tire is stored or in service.
– Vehicle restriction.
The temporary spare tire was specifically designed for your car and
should not be used on any other vehicle.
– Other restrictions.
The temporary spare tire should not be used with other wheels, nor
should standard tires, snow tires, wheel covers, or trim rings be used
with the temporary spare wheel. If such use is attempted, damage to
these items or other vehicle components may occur.
TIRE SERVICE ASSISTANCE OR INFORMATION
When you have tire problems, Hankook provides service and assistance.
Any time you see damage to your tires, contact your local Hankook Tire
Dealer.
If no local dealer is available around you, dial Hankook Toll Free Service
Number so that you can get information on where and how service is
rendered to you.
FOR SERVICE ASSISTANCE OR INFORMATION
U.S.A.
CORPORATE HEADQUARTERS
1450 Valley Road, Wayne, New Jersey 07470 1–973-633-9000 Toll Free1–877-740-7000
WEST REGIONAL OFFICE
11555 Arrow Route, Suite 105, Rancho Cucamonga, CA 91730 1–909-481-9800 To l l F r e e1–800-426-8252
CANADA
CORPORATE HEADQUARTERS
30 Resolution Dr., Brampton, Ontario L6W 0A3 1–905-463-9802 Toll Free1–800-843-7709
HANKOOK TIRES
144

The
cost
of
applicable
taxes
and
mounting
and
balancing
and
any

other
service
charges.
 Tire
damage
or
irregular
wear
due
to:
" Road
hazard,
including
puncture,
cut,
impact
break,
bulge,
snag,

stone
drill,
collision.
# Continued
use
while
run
flat
or
under
acute
VOEFSJOGMBUJPO.
$ Improper
use
or
operation,
without
limitation,
improper
inflation

pressure,
overloading,
use
of
an
improper
rim,
tire/wheel
assem-
bly
imbalance
or
other
vehicle
condition,
worn
suspension
compo-
nents,
improper
mounting
or
de-mounting,
misuse,
misapplica-
tion,
fire
or
other
externally
generated
heat,
water
or
other
material

trapped
inside
the
tire
during
mounting,
tire
alteration,
racing
or

competition
purposes,
improper
inserting
of
sealant,
balance
or

filler
materials.
% Improper
repair
,
or
with
repairs


not
conforming
to
the
Rubber

Manufacturers
Association
standards,
or
with
section
repairs,
or

with
self-vulcanizing
plug
only.
& Failure
to
rotate
the
tire
at
least
every
5,000
miles
as
evidenced
by

Kumho’s
Mileage
Warranty/Tire
Rotation
Card
(printed
in
this

brochure)
or
vehicle
misalignment.
' Uneven
or
rapid
wear
which
is
caused
by
mechanical
irregularity

in
the
vehicle
such
as
misalignment,
(a
measured
tread
difference

of
2/32nds
of
an
inch
or
more
across
the
tread
on
the
same
tire).
 Ozone
or
weather
cracking
on
tires
over
four
(4)
years
from
the
date
of

manufacture.
 Tires
that
have
been
recapped,
or
retreaded,
regrooved.
 Ride
disturbance
(out-of-round,
vibration,
pulling,
etc.)
claims
submit-
ted
after
the
first
2/32
of
tread
wear.
 Loss
of
time,
or


use,
inconvenience,
or
any
incidental
or
consequential

damage.
 Tires
that
have
been
modified
by
the
addition
or
removal
of
material

or
any
tire
intentionally
altered
to
change
its
appearance.
 Tires
unserviceability
caused
by
the
tire
operation
in
excess
of

tire/wheel
manufacturers
specifications
and
recommendations.
KUMHO TIRES
148

Temporary Spares
MICHELIN® temporary spare tires are covered by this warranty for 6
years from the date of purchase or until the first 2/32 nds of an inch (1.6
mm) of the original tread is worn off. Date of purchase is documented by
new vehicle registration or tire sales invoice. If no proof of purchase is
available, coverage will be based on date of manufacture. At that time, all
warranties, express or implied, expire.
WHAT IS NOT COVERED
Tires which become unserviceable due to:
•Road hazard injury (e.g., a cut, snag, bruise, impact damage or
puncture);
• Incorrect mounting of the tire, tire/wheel imbalance or improper
repair;
• Misapplication, improper maintenance, racing, underinflation, overin-
flation or other abuse;
• Uneven or rapid wear which is caused by mechanical irregularity in
the vehicle such as wheel misalignment, (a measured tread difference
of 2/32 nds of an inch (1.6 mm) or more across the tread on the same
tire);
• Accident, fire, chemical corrosion, tire alteration, or vandalism;
• Use in commercial applications for tread wear; by this warranty for 6
years;
• Flat spotting caused by improper storage or brake lock;
• The addition of liquid, solid or gaseous materials other than air,
nitrogen or carbon dioxide (for example, waterbase sealers or balanc-
ing substances);
• Cosmetic ozone or weather cracking;
• Use of MICHELIN Self-Supporting Zero Pressure (AP) tires without a
properly operating low air pressure warning system.
MICHELIN
162