2020 AUDI R8 COUPE wheel bolt torque

Emergency assistance

> Slide the plastic clip from the vehicle tool kit
onto the cap until it engages > fig. 199.
>» Remove the cap with the plastic clip.
Anti-theft wheel bolts
Applies to: vehicles with anti-theft wheel bolts
me
v a
Fig. 200 Anti-theft wheel bolt with cap and adapter

B4H-0470


You need a special adapter in the vehicle tool kit
to remove the anti-theft wheel bolts.
> Remove the cap (2).
> Slide the adapter @) all the way onto the anti-
theft wheel bolt @.
>» Slide the wheel wrench from the vehicle tool kit
all the way onto the adapter @).
> Loosen the wheel bolt > page 274.
G) Tips
Note the code number for the wheel bolt
adapter and store it in a safe place separate
from the vehicle. If you need a replacement
adapter, contact an authorized Audi dealer or
authorized Audi Service Facility and give them
the code number.

Loosening the wheel bolts


| B8K-1481

Fig. 201 Changing a tire: loosen the wheel bolts
> Slide the wheel wrench from the vehicle tool kit
all the way onto the wheel bolt).
> Turn the wheel bolt approximately one turn to
the left. To achieve the required torque, hold
the end of the wheel wrench. If the wheel bolt
will not loosen, press carefully on the wheel
wrench with your foot. Hold onto the vehicle se-
curely while doing this and make sure your foot-
ing is stable.

ZA WARNING
To reduce the risk of an accident, only loosen
the wheel bolts gently one turn before raising


the vehicle with the vehicle jack*.


D_ You need the matching adapter in order to loosen and
tighten anti-theft wheel bolts* > page 274.
274

Emergency assistance

Removing and mounting a wheel
2 i
2 Q
+ ao

B4s-0154


Fig. 205 Wheel: alignment pin in the top and bottom
holes
Removing a wheel
> Remove the top and bottom wheel bolts com-
pletely using the hex socket in the screwdriver
handle (in the vehicle tool kit) > fig. 204 and
place it on a clean surface.
> Install the alignment pins (from the vehicle
tool kit) by hand into the empty holes
> fig. 205.
> Remove the rest of the wheel bolts.
> Remove the wheel >(@). The alignment pins re-
main in the holes.
Installing a wheel
Read the directions on > page 276 when instal-
ling unidirectional tires.
> Slide the wheel on over the alignment pins
>©.
> Install the wheel bolts and tighten them gently
using the hex socket.
> Remove the alignment pins and also tighten
the remaining wheel bolts.
> Carefully lower the vehicle using the vehicle
jack*.
276
> Tighten the wheel bolts in a diagonal pattern
using the wheel wrench.
The wheel bolts must be clean and loosen and
tighten easily. Check the contact surfaces for the
wheel and hub. Contaminants on these surfaces
must be removed before installing the wheel.

ZA WARNING
— Read and follow the important information
and notes under > page 251.
— Never use the hex socket in the screwdriver
handle to tighten the wheel bolts. Using the
hex socket will not achieve the required
tightening torque, which increases the risk
of an accident.
(!) Note
When removing or installing the wheel, the
rim
could hit the brake rotor and damage the
rotor. Work carefully and have a second per-
son help you.
Unidirectional tires
A unidirectional tire profile is identified by arrows
on the tire sidewall that point in the running di-
rection. You must always maintain the specified
running direction. This is necessary to ensure the
tire's optimal performance in regard to adhesion,
running noise, and friction, and to reduce the risk
of
hydroplaning.

To benefit fully from the advantages of the uni-
directional tire design, you should replace faulty
tires as soon as possible and restore the correct
running direction on all of the tires.
> Reinstall the caps on the wheel bolts if necessa-
ry.
> Store the vehicle tool kit in its designated
place.
> Make sure that the wheel that was removed,
the vehicle tool kit, and the vehicle jack* are se-
curely stored in the luggage compartment
=> page 54.

4S1012721BA
Emergency assistance

> Check the tire pressure on the installed wheel
as soon as possible.
> Check the tire pressure and store it in the Info-
tainment system.
> The wheel bolt tightening specification must be
90 ft lbs (120 Nm). Have it checked as soon as
possible with a torque wrench. Drive carefully
until then.
> Have the faulty wheel replaced as quickly as
possible.
Jump starting
You should only perform the steps that follow if
you have the necessary tools and technical ex-
pertise.
If the engine does not start because the vehicle
battery is drained, you can jump start your vehi-
cle using another vehicle. Jump start cables are
needed to do this.
Both vehicle batteries must have 12 V nominal
voltage. The voltage capacity (Ah) of the vehicle
battery that is giving power must not be less
than the capacity of the drained vehicle battery.
Jump start cable
Only use a jump start cable with a large enough
diameter. Note the manufacturer's specifica-
tions.
Only use a jump start cable with insulated termi-
nal clamps.
Positive cable - usually red.
Negative cable - usually black.

ZA WARNING
— A drained vehicle battery can freeze at tem-
peratures around 32 °F (0 2C). If the vehicle
battery is frozen, it must be thawed before
connecting the jump start cables. If it is not,
the risk of an explosion and chemical burns
increases. After jump starting the vehicle,
drive to an authorized Audi dealer or author-
ized Audi Service Facility immediately to
have the vehicle battery checked.

— Read the warnings when working in the en-
gine compartment > page 229.
— Handling the jump start cables incorrectly
may cause the vehicle battery to explode


and lead to serious injuries.


C) Note
Jump start cables can cause considerable
damage to the vehicle electrical system if
they are connected incorrectly.
@ Tips
— There must be no contact between the vehi-
cles, or else voltage could flow when con-
necting the positive terminal and drain the
vehicle battery of the vehicle providing the
jump start.
— The drained vehicle battery must be con-
nected correctly to the electrical system.
— Switch off electrical equipment that is not
needed.
Starting the engine
Both jump start cables must be connected in the
correct order.
B4S-0067

Fig. 206 Luggage compartment: connectors for jump start
cables or a charger
RAZ-0129)

Fig. 207 Connecting the jump start cables
277