2020 AUDI A4 tow

8W1012721BB
Emergency assistance

Emergency assistance
General information
> Park the vehicle as far as possible from moving
traffic in the event of a breakdown. In the event
of a flat tire, park the vehicle ona level surface.
If you are ona steep hill, be especially careful.
> Set the parking brake.
> Switch the emergency flashers on.
> Have the passengers exit the vehicle. They
should move to a safe place, for example be-
hind a guard rail.

Z\ WARNING
Follow the steps given above. This is for your
protection and the for the safety of others on
the road.

Equipment
Vehicle tool kit, tire
vehicle jack
Applies to: vehicles with the vehicle tool kit, tire mobility kit,
and vehicle jack
yi aYaLaL eae Tale|

Fig. 172 Luggage compartment: cargo floor cover
The vehicle tool kit, vehicle jack, tire mobility kit
and compressor are stored in the luggage com-
partment under the cargo floor cover.
» Applies to: sedan: To open the front compart-
ment, lift the cargo floor cover by the strap (@).
> Applies to: allroad: To open the front compart-
ment, pull the cargo floor cover by the plastic
handle @) slightly toward the rear. Lift the car-
go floor cover over the front compartment.
> To open the rear compartment, lift the cargo
floor cover by the plastic handle @).
» Applies to: sedan: Hook the plastic handle (2)
into the luggage compartment seal.
> To remove the cargo floor cover completely,
pull it toward the rear at the plastic handle @).
> Applies to: vehicles with spare tire: Turn the
handle counter-clockwise and remove the spare
tire.
> Applies to: sedan: Unhook the cargo floor cover
again
before closing the luggage compartment
lid.
Depending on vehicle equipment, the vehicle tool
kit, tire mobility kit, and compressor may be lo-
cated under another cover that is secured with a
handwheel.
Applies to: vehicles with vehicle jack in the stor-
age bag: The bag with the vehicle jack is secured
to the tie-downs in the luggage compartment
and must be secured to the tie-downs again after
using it.

ZX WARNING
Applies to: vehicles with vehicle jack in the storage bag
A vehicle jack that is unsecured, incorrectly se-
cured, or not secured in the luggage compart-
ment may slide out of place when braking,
turning,
or in an accident, which increases the
risk of injuries to vehicle passengers. To re-
duce the risk of an accident, never transport
the vehicle jack without securing it.
G) Tips
—Insome vehicles, the rear compartment
may not open.
— The vehicle jack in your vehicle is mainte-
nance-free.


Tire mobility kit
Applies to: vehicles with tire mobility kit
> Read and follow the important safety precau-
tions > page 253.
> Set the parking brake.
> Select the “P” position.
> Check if a repair with the tire mobility kit is pos-
sible > page 254.
253

Emergency assistance

> Set the parking brake.
> Select the “P” position.
>» When towing a trailer: disconnect the trailer
from your vehicle.
> Lay out the vehicle tool kit > page 253 and the
spare tire > page 258.
> Switch the ignition off.
> Turn the wheel bolt approximately one turn to
the left. To achieve the required torque, hold
the end of the wheel wrench. If the wheel bolt
will not loosen, press carefully on the wheel
wrench with your foot. Hold onto the vehicle se-
curely while doing this and make sure your foot-
ing is stable.

ZA WARNING
The vehicle must also be secured to prevent it
from rolling when using the vehicle jack*. Use
suitable objects to block the front and back of
the wheel that is diagonal from the wheel
with the flat tire.


Removing the caps



@

ie

zis
Fig. 176 Wheel: wheel bolts with caps
?
> Slide the plastic clip from the vehicle tool kit
onto the cap until it engages > fig. 176.
> Remove the cap with the plastic clip.
Loosening the wheel bolts
©
i=
x © a


Fig. 177 Wheel: loosening the wheel bolt
> Slide the wheel wrench from the vehicle tool kit
all the way onto the wheel bolt.
256
ZA WARNING
To reduce the risk of an accident, only loosen
the wheel bolts gently one turn before raising
the vehicle with the vehicle jack*.

Raising the vehicle
Applies to: vehicles with vehicle jack
© & Ss
g
= % oo


Fig. 179 Sill: positioning the vehicle jack
> Place the vehicle jack from the vehicle tool kit
ona firm surface. Use a flat, stable support if
necessary. Ona slippery surface such as tile,
you should use a non-slip pad such as a rubber
mat > A\.
> Find the marking on the sill that is closest to
the tire that will be changed > fig. 178. Behind
the marking, there is a lifting point on the side
sill for the vehicle jack.
> Turn the handwheel to raise the vehicle jack un-
der the lifting point on the side sill until the >

8W1012721BB
Emergency assistance

1. Attach one end of the positive cable (red) to
the jump-start pin @ > fig. 183 on your vehi-
cle.
2. Attach the other end of the positive cable
(red) to the positive terminal @ on the pow-
er source.
Connecting the negative cable (black) to the
negative terminal
3. Attach one end of the negative cable (black)
to the negative terminal @) on the power
source.
4. Attach the other end of the negative cable
(black) to the negative terminal @) on the ve-
hicle.
Starting the engine
> Start the engine in the vehicle giving the charge
and let it run at idle.
> Now start the engine in your vehicle, which has
the
drained battery.
> If the engine does not start, stop the starting
procedure after 10 seconds and then repeat it
after approximately 30 seconds.
> Turn on the rear window defogger in your vehi-
cle in order to reduce any voltage peaks that
may occur when disconnecting the jump start
cables. The headlights must be switched off.
> With the engines running, remove the cables in
reverse order of the way they were installed.
> Close the red cover on the positive terminal.

ZA WARNING
— Never connect the jump start cable directly
to your vehicle battery. Only use the connec-
tions in the engine compartment.
— Do not touch the non-insulated parts of the
terminal clamps. The cable must also not
come into contact with vehicle components
that conduct electricity when it is connected
to the positive vehicle battery terminal. This
can cause a short circuit.
— The plugs on the battery cells must not be
opened.
— Keep ignition sources (such as open flames,
burning cigarettes, etc.) away from the vehi-
cle batteries to reduce the risk of an explo-
sion.

— Route the jump start cables so they cannot
get caught in the moving parts in the other


vehicle's engine compartment.
Q) Note
Please note that the connecting process previ-
ously described for the jump start cables is in-
tended for when your vehicle is being jump
started.
@) Tips
Make sure that the connected jump start ca-
bles have sufficient contact with metal.

Towing
General information
You should only perform the steps that follow if
you have the necessary tools and technical ex-
pertise.
Towing requires a certain amount of practice.
Audi recommends contacting a towing company
to have the vehicle transported.
You should only have your vehicle towed by an-
other vehicle when disabled in exceptional cir-
cumstances. Inexperienced drivers should not
tow.
Notes on towing
When the engine is stopped, the transmission
will not be sufficiently lubricated if traveling at
high speeds and long distances:
— The maximum permitted towing speed is 30
mph (50 km/h).
— The maximum permitted towing distance is 30
miles (50 km).
Additional information on towing with a tow
truck
The vehicle may only be towed with the front axle
raised. Do not wrap any chains or cables around
the brake lines.
Tow bar and towing cable
The vehicle can be towed with a tow bar or tow-
ing cable. Both drivers should be familiar with
261
>

Emergency assistance

the special considerations when towing, especial-
ly when using a towing cable.
Always make sure the traction force does not ex-
ceed the permitted level and there are no shock
loading conditions. There is always the risk of the
coupling becoming overloaded when driving off-
road.
For the most safety and security, drive with a tow
bar. You should use a towing cable only if a tow
bar is not available. Use a towing cable made of
synthetic elastic cable similar elastic material.

Z\ WARNING
— Towing highly increases the risk of an acci-
dent, for example from colliding with the
towing vehicle.
—To reduce the risk of an accident, do not al-
low anyone to remain inside the vehicle
when it is being transported by a tow truck
or a special transporter.
@) Note
— If normal towing is not possible, for exam-
ple if the transmission is faulty or if the
towing distance is greater than 30 miles
(50 km), then transport the vehicle on a
special carrier.
— If the vehicle is towed by a tow truck at the
axle that is not permitted, this can cause se-
vere damage to the transmission.
— The vehicle must not be tow started for
technical reasons.
@ Tips
— If the power supply is interrupted, then it
will not be possible to move the selector
lever out of the "P" position. The parking
lock must be released using the emergency
release before towing the vehicle
=> page 97.
— Follow the local legal regulations for tow-
ing.
Read and follow the important information under
=> page 261.


262
Preparations
> Only secure the towing cable or tow bar at the
designated towing loop > page 262.
> Make sure the towing cable is not twisted. Oth-
erwise it could disconnect from the towing loop
while towing.
> Switch the emergency flashers on in both
vehicles > page 50. However, do not do this if it
prohibited by law.
Towing vehicle (front)
> Only start to drive when the towing cable is
taut.
> Press the brake pedal very carefully.
> Avoid sudden braking or driving maneuvers.
Vehicle being towed (rear)
> Make sure the ignition is switched on so that
the steering wheel is not locked and so that you
can use the turn signals, the horn, and the
windshield wipers if needed > A\.
> Switching it off before the vehicle has stopped
may impair the function of the brake booster
and power steering. You would then need to
use more force to steer and brake the vehicle.
> Release the parking brake > page 102.
> Select the “N” selector lever position.
» Make sure the towing cable is always taut.

ZA WARNING
Never tow a vehicle using a tow bar or towing
cable if the vehicle does not have electrical
power.

Rear towing loop




Fig. 184 Rear bumper: installing the towing loop

8W1012721BB
Emergency assistance

The threaded opening for the towing loop is lo-
cated on the right rear of the bumper.
> Remove the towing loop from the vehicle tool
kit > page 253.
> Press the cap inward with brief, strong pressure
> fig. 184. The cap will loosen from the bump-
er.
> Tighten the towing loop in the threaded open-
ing until it stops and then tighten it with a
wheel wrench.
> After using, place the towing loop back in the
vehicle tool kit.

If the towing loop is not tightened until it
stops when installing, the threads may be
pulled out when towing the vehicle and result
in an accident.

Depending on the model, the shape of the
cover can vary.
263

Index

Touch display
Adjusting the brightness..............-. 18
TPMS
Tire pressure monitoring system........ 245
Traffic information...............00000- 186
Online traffic information.............. 185
also refer to Online traffic information... 185
Trafficjamiassist's sss 2 sss vo even oo soe 134
Traffic light information................ 120
Traffic sign recognition................. 118
Traffic’ SigtS ses: < = seee ss mem tv eee soe 121
Trailer towing.......... 0... cee eee eee 112
TONGUE WEIGKts « & sess « » sever x 2 wawe a exe L12
Trailerload «5 ccc so sesmee « oramess ao coenees wo 112
TUPMASSISE secs oo csecers oo weaaee oe comin ao eee 142
Turnsignal srsics a = cies «2 meee «2 wawen 6 ee 49
U
Uniform tire quality grading............. 243
Unlocking and locking. ..............0005 30
Bysremiote:control.. « scsi sv nmin 6 o eames vee 35
Using the lock cylinder................. 32
With the central locking switch.......... 32
With the convenience key............... 35
Update (Software) ices cs sssseu oo savin oo swe 207
USB
IAGAPEOR « ss mec = suances 1 « wane a + swewon & 5 at 160
USBicharging ports. . wens «x swauue ¥ x sons © arene 78
USB drive
Supported types/formats.............. 201
USB stick
refer to Audi music interface........... 196
Users
LO¢al USERS wane: x x seme 5 2 meee 2 eee 2 5 oe 27
MMYAUGEUSCDS is oo cess 2 6 wanes + sete a = ea 27
Using residual heat. .... 0.0... 0c cece e nee 90
V
Valet parking sews «= sees = s eee es cee ee bes 44
Vanity OP icx « = cacy & 2 seus © 2 wows 5 y wee & 54
290

Vehicle
Care/cleaning........ 2. cece eee eee ee 247
DIMERSIONS « easy s x wee s wenn se Wee a 277
Identification data................0.. 277,
Out of service... 6... ee eee eee ee 252
RaiSinG’: 5 = sees & x ween 5 3 wees ¢ y eee ¢ eos 256
StartinGbsvis & + wwe 2 6 eww 2 6 ase 2 eww we 92
Vehicl@eare snow s eam ss wives a ¢ wens + & ess 247
Vehicle control services..............0.. L71,
Vehicle data label...............--0000- 277
Vehicle identification number............ 277
Vehicle jack. .... 2... ee eee eee eee 253
LifEiNG POINtS an « « aees s waas ao pews se row 256
Vehicle key os ¢ s seed co eee ss ease es pees 30, 34
Vehicle starting system. ............200- 100
Vehicle tool kit............. 00.22 eee eee 253
Ventilation... 2.0... . cee eee eee eee 87
VIEW button. ........ 0.00. f eee eee eee ee 12
Woicermaibecns ico ccnceie va comers vw asecone woo axes © « 164
Voice recognition system.............0-0. 24
External... 2... 2... eee eee eee 25
Operating s < = esos x s ewe < 4 eee ye GF Sanas Go 24
Ww
Warning lights
refer to Indicator lights...........--0000- 7
Washing matte finish paint.............. 247
Wave band
refer to Frequency band............... 188
Weightsies <= cess ss news se tees e aan se He 278
WHEEL bOltSs » snau se aeay sx meme 2 neem 2 a 242
Changingia tines 2 sxe x 2 snes «x ananan @ ona 255
Whee lst. & scent oo ome so emu oo vere 2s me 227
Cleaning... .. cece cece ee eee eee 248
Glossary of tire and loading terminology .. 230
Replacing « waa a s sone s ¢ wane 2 2 means ¢ 2 ve 255
Tire pressure monitoring system........ 245
Tires and vehicle load limits............ 240
Wheelwrench.............--000ee eee 253
Wi-Fi
Hotspot settingS............ceeeeveee 172
Using:a hotspots seicne so cvs 2 2 eae 2 & ewe 170
Windows
Child safety lock... 2... ee eee eee eee ee 4l
Cleaning and removing ice............. 249
Convenience opening and closing......... 42