2019 YAMAHA YXZ1000R SS torque

4-37
4
YXZ10YEXK
YXZ10YESK3. Tighten the locknut to the specified
torque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
Crossover setting (YXZ10YESK)
The crossover setting adjusts the timing when
the shock absorber transitions from the soft
spring to the hard spring.TIP It is recommended to adjust the crossover
setting a similar distance whenever the
spring preload is adjusted.
 The crossover setting is measured from the
bottom of the spring retainer to the top of
the crossover locknut.
1. Distance A
1. Distance A
11
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)
UB5H7AE0.book Page 37 Wednesday, July 4, 2018 1:37 PM

4-39
4
3. Tighten the locknut to the specifiedtorque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
1. Distance B
2. Spring retainer
3. Crossover locknut
4. Crossover adjusting nutCrossover setting: Minimum (soft):Distance B = 19.1 mm (0.75 in)
Standard (recommended): Distance B = 31.8 mm (1.25 in)
Maximum (hard): Distance B = 44.5 mm (1.75 in)
3
4 12
(b)
(a)
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)1. Special tool
2. Torque wrench
3. Crossover locknut
21
3
90
UB5H7AE0.book Page 39 Wednesday, July 4, 2018 1:37 PM

4-48
4
YXZ10YEXK
YXZ10YESK3. Tighten the locknut to the specified
torque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
Crossover setting (YXZ10YESK)
The crossover setting adjusts the timing when
the shock absorber transitions from the soft
spring to the hard spring.TIP It is recommended to adjust the crossover
setting a similar distance whenever the
spring preload is adjusted.
 The crossover setting is measured from the
bottom of the spring retainer to the top of
the crossover locknut.
1. Distance A
1. Distance A
11
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)
UB5H7AE0.book Page 48 Wednesday, July 4, 2018 1:37 PM

4-50
4
3. Tighten the locknut to the specifiedtorque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
1. Distance B
2. Spring retainer
3. Crossover locknut
4. Crossover adjusting nutCrossover setting: Minimum (soft):Distance B = 48.4 mm (1.91 in)
Standard (recommended): Distance B = 61.1 mm (2.41 in)
Maximum (hard): Distance B = 73.8 mm (2.91 in)
32
4 1
(b)
(a)
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)1. Special tool
2. Torque wrench
3. Crossover locknut
21
3
90
UB5H7AE0.book Page 50 Wednesday, July 4, 2018 1:37 PM

5-8
5
EBU36672YCC-S clutchCheck the YCC-S clutch fluid level and cor-
rect if necessary. (See page 8-48.)
Check the operation of the drive select lever
and shift paddles at the start of each drive.TIPIf the YCC-S clutch fluid level was low, be
sure to check the clutch system for leak-
age.
 If any leakage is found, or if shifting is not
smooth, have a Yamaha dealer service the
vehicle. EBU35700Fittings and fastenersAlways check the tightness of chassis and
wheel fittings and fasteners before starting
off. Take the vehicle to a Yamaha dealer or re-
fer to the Service Manual for correct tighten-
ing torque.
EBU31840Instruments, lights and switchesCheck that all instruments, lights and switch-
es are working properly. Correct if necessary.EBU31851Control cablesWhen driving in cold weather, always make
sure all control cables work smoothly before
starting off. WARNING! Control cables can
freeze in cold weather and you could be
unable to control the vehicle.
[EWB03280]
EBU37892
TiresCheck and adjust the tire pressure before
each ride. Check tires for wear and damage.
UB5H7AE0.book Page 8 Wednesday, July 4, 2018 1:37 PM

8-2
8
EBU33561Owner’s Manual and tool kitYou are recommended to put this manual in
the vinyl bag and always carry it in the glove
compartment as shown. Put the tool kit and
tire pressure gauge under the passenger
seat.The maintenance information included in this
manual is intended to provide you, the owner,
with the necessary information for completing
your own preventive maintenance and minor
repairs.
The tools provided in the tool kit are sufficient
for this purpose, and should be kept on the
vehicle in case of emergency repairs.
Other tools and equipment are required for
certain service items. If you do not have a
torque wrench available during a service op-1. Owner’s Manual
1
1. Tool kit
2. Tire pressure gauge
1
2
UB5H7AE0.book Page 2 Wednesday, July 4, 2018 1:37 PM

8-3
8
eration requiring one, take your vehicle to a
Yamaha dealer to check the torque settings
and adjust them as necessary.UB5H7AE0.book Page 3 Wednesday, July 4, 2018 1:37 PM

8-15
8
To install the panel1. Place the panel in the original position,and then install the bolts and the quick
fastener screws. 2. Install the passenger seat by installing the
bolts, and then tighten them to the spec-
ified torque.
TIPMake sure that the seat frame is properly
secured.
1. Panel B
2. Quick fastener screw
3. Bolt
1
2
2
3
2
3
3
1. Panel BTightening torque:
Passenger seat bolt:32 N·m (3.2 kgf·m, 24 lb·ft)
1
UB5H7AE0.book Page 15 Wednesday, July 4, 2018 1:37 PM