2019 YAMAHA YXZ1000R SS lock

4-36
4
YXZ10YESK (LE model)TIPThe spring preload setting is determined by
measuring distance A, shown in the illustra-
tion. The shorter distance A is, the higher the
spring preload; the longer distance A is, the
lower the spring preload. 1. Locknut
2. Special wrench
3. Spring preload adjusting nut
2
1
3
(a)
(b)
Spring preload setting:Minimum (soft):Distance A =
437.6 mm (17.23 in) (YXZ10YEXK)
501.7 mm (19.75 in) [YXZ10YESK (LE
model), YXZ10YESK (SE model)]
Standard: Distance A =
424.9 mm (16.73 in) (YXZ10YEXK)
489.0 mm (19.25 in) [YXZ10YESK (LE
model), YXZ10YESK (SE model)]
Maximum (hard): Distance A =
412.2 mm (16.23 in) (YXZ10YEXK)
476.3 mm (18.75 in) [YXZ10YESK (LE
model), YXZ10YESK (SE model)]
UB5H7AE0.book Page 36 Wednesday, July 4, 2018 1:37 PM

4-37
4
YXZ10YEXK
YXZ10YESK3. Tighten the locknut to the specified
torque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
Crossover setting (YXZ10YESK)
The crossover setting adjusts the timing when
the shock absorber transitions from the soft
spring to the hard spring.TIP It is recommended to adjust the crossover
setting a similar distance whenever the
spring preload is adjusted.
 The crossover setting is measured from the
bottom of the spring retainer to the top of
the crossover locknut.
1. Distance A
1. Distance A
11
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)
UB5H7AE0.book Page 37 Wednesday, July 4, 2018 1:37 PM

4-38
4
1. Loosen the crossover locknut as shown.2. Turn the crossover adjusting nut in direc-
tion (a) to increase the crossover setting
and in direction (b) to decrease the cross-
over setting.1. Distance B
2. Spring retainer
3. Crossover locknut
4. Crossover adjusting nut
3
4 12
1. Special tool
2. 3/8 inch (9.5 mm) drive wrench
3. Crossover locknut
12
3
90
UB5H7AE0.book Page 38 Wednesday, July 4, 2018 1:37 PM

4-39
4
3. Tighten the locknut to the specifiedtorque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
1. Distance B
2. Spring retainer
3. Crossover locknut
4. Crossover adjusting nutCrossover setting: Minimum (soft):Distance B = 19.1 mm (0.75 in)
Standard (recommended): Distance B = 31.8 mm (1.25 in)
Maximum (hard): Distance B = 44.5 mm (1.75 in)
3
4 12
(b)
(a)
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)1. Special tool
2. Torque wrench
3. Crossover locknut
21
3
90
UB5H7AE0.book Page 39 Wednesday, July 4, 2018 1:37 PM

4-46
4
NOTICEECB00091Never turn an adjusting mechanism be-
yond the minimum and maximum settings. Spring preload1. Loosen the locknut.
2. Turn the spring preload adjusting nut in direction (a) to increase the spring pre-
load and thereby harden the suspension,
and in direction (b) to decrease the spring
preload and thereby soften the suspen-
sion. YXZ10YEXK
1. Locknut
2. Spring preload adjusting nut
3. Special wrench
1
3
2
(a)
(b)
UB5H7AE0.book Page 46 Wednesday, July 4, 2018 1:37 PM

4-47
4
YXZ10YESKTIPThe spring preload setting is determined by
measuring distance A, shown in the illustra-
tion. The shorter distance A is, the higher the
spring preload; the longer distance A is, the
lower the spring preload. 1. Locknut
2. Spring preload adjusting nut
3. Special wrench
1
3
2
(a)
(b)
Spring preload setting:Minimum (soft):Distance A =
433.1 mm (17.05 in) (YXZ10YEXK)
610.9 mm (24.05 in) [YXZ10YESK (LE
model), YXZ10YESK (SE model)]
Standard: Distance A =
420.4 mm (16.55 in) (YXZ10YEXK)
598.2 mm (23.55 in) [YXZ10YESK (LE
model), YXZ10YESK (SE model)]
Maximum (hard): Distance A =
407.4 mm (16.04 in) (YXZ10YEXK)
585.5 mm (23.05 in) [YXZ10YESK (LE
model), YXZ10YESK (SE model)]
UB5H7AE0.book Page 47 Wednesday, July 4, 2018 1:37 PM

4-48
4
YXZ10YEXK
YXZ10YESK3. Tighten the locknut to the specified
torque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
Crossover setting (YXZ10YESK)
The crossover setting adjusts the timing when
the shock absorber transitions from the soft
spring to the hard spring.TIP It is recommended to adjust the crossover
setting a similar distance whenever the
spring preload is adjusted.
 The crossover setting is measured from the
bottom of the spring retainer to the top of
the crossover locknut.
1. Distance A
1. Distance A
11
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)
UB5H7AE0.book Page 48 Wednesday, July 4, 2018 1:37 PM

4-49
4
1. Loosen the crossover locknut as shown.2. Turn the crossover adjusting nut in direc-
tion (a) to increase the crossover setting
and in direction (b) to decrease the cross-
over setting.1. Distance B
2. Spring retainer
3. Crossover locknut
4. Crossover adjusting nut
32
4 1
1. Special tool
2. 3/8 inch (9.5 mm) drive wrench
3. Crossover locknut
12
3
90
UB5H7AE0.book Page 49 Wednesday, July 4, 2018 1:37 PM