2019 YAMAHA KODIAK 450 brake

8-39
8
EBU28414Checking the front brake pads and rear
brake friction platesThe front brake pads and the rear brake friction
plates must be checked for wear at the intervals
specified in the periodic maintenance and lubrica-
tion chart.TIPThis ATV is equipped with a wet, multiple-disc
type rear brake, which is located inside of the final
gear case. EBU24174Front brake padsCheck each front brake pad for damage and mea-
sure the lining thickness. If a brake pad is dam-
aged or if the lining thickness reaches the
specified limit, have a Yamaha dealer replace the
brake pads as a set.
TIPThe wheels need to be removed to check the
brake pads. (See page 8-63.) EBU30321Rear brake friction plates
The rear brake friction plates must be checked
and, if necessary, replaced by a Yamaha dealer at
the intervals specified in the periodic maintenance
and lubrication chart.EBU29844Checking the brake fluid levelBefore riding, check that the brake fluid is above
the minimum level mark. Replenish the brake fluid
if necessary.
1. Lining thickness
Brake pad lining thickness limit:
1.0 mm (0.04 in)
UBB561E0.book Page 39 Monday, March 26, 2018 11:15 AM

8-40
8
TIPStraighten the handlebars for an accurate reading. NOTICEECB01161Brake fluid may damage painted surfaces or
plastic parts. Always clean up spilled fluid im-
mediately.
As the brake pads wear, it is normal for the brake
fluid level to gradually go down. A low brake fluid
level may indicate worn brake pads or brake sys-
tem leakage. Therefore, be sure to check the
brake pads for wear and the brake system for
leakage. If the brake fluid level suddenly goes
down, have a Yamaha dealer the brake system
before further riding.
WARNING
EWB02721Improper maintenance can result in loss of
braking ability. Observe these precautions:
Insufficient brake fluid may allow air to enter
the brake system, reducing braking perfor-
mance.
 Clean the filler cap before removing. Use
only DOT 4 brake fluid from a sealed contain-
er.
 Use only the specified brake fluid; otherwise,
the rubber seals may deteriorate, causing
leakage.
 Refill with the same type of brake fluid. Add-
ing a brake fluid other than DOT 4 may result
in a harmful chemical reaction.
1. Minimum level markSpecified brake fluid:
DOT 4
1
UBB561E0.book Page 40 Monday, March 26, 2018 11:15 AM

8-41
8
Be careful that water does not enter the
brake fluid reservoir when refilling. Water will
significantly lower the boiling point of the flu-
id and may result in vapor lock.
EBU24283Changing the brake fluidHave a Yamaha dealer change the brake fluid at
the intervals specified in the periodic maintenance
and lubrication chart. In addition, have the oil seals
of the brake master cylinder and calipers as well
as the brake hoses replaced at the intervals listed
below or whenever they are damaged or leaking.
Oil seals: Replace every two years.
 Brake hoses: Replace every four years.
EBU24396Checking the front brake lever free
playThere should be no free play at the brake lever
end. If there is free play, have a Yamaha dealer in-
spect the brake system.EBU30348Adjusting the rear brake lever and
brake pedalThe rear brake lever free play, brake pedal free
play, and the brake pedal height must be checked
and adjusted at the intervals specified in the peri-
odic maintenance chart.1. No brake lever free play
UBB561E0.book Page 41 Monday, March 26, 2018 11:15 AM

8-42
8
Adjusting the brake lever free play
Measure the brake lever free play and adjust if
necessary.
1. Loosen the locknut at the brake lever. 2. To increase the brake lever free play, turn the
brake lever free play adjusting bolt in direction
(a). To decrease the brake lever free play, turn
the adjusting bolt in direction (b). NOTICE:
Distance A must not measure more than
12.7 mm (0.50 in). If distance A exceeds
12.7 mm (0.50 in), the specified brake lever
free play cannot be obtained, therefore
proceed with the following steps.
[ECB01143]
1. Brake lever free playBrake lever free play: 10.0 mm (0.39 in)
1
1. Locknut
2. Distance A
3. Brake lever free play adjusting bolt
12
3
(a)
(b)
UBB561E0.book Page 42 Monday, March 26, 2018 11:15 AM

8-43
8
TIPIf the specified brake lever free play could be ob-
tained as described above, skip steps 3-8. 3. Fully turn the adjusting bolt in direction (a) toloosen the brake cable.
4. Slide the rubber cover back.
5. Loosen the brake cable adjuster locknut.
6. To increase the brake lever free play, turn the brake lever free play adjusting nut in direction
(a). To decrease the brake lever free play, turn the adjusting nut in direction (b).
NOTICE:
Make sure that distance B measures 22
mm (0.87 in) or less. If distance B reaches
22 mm (0.87 in), adjust the brake lever free
play at the brake lever again. If distance A
exceeds 12.7 mm (0.50 in), have a Yamaha
dealer check the vehicle.
[ECB01153]
7. Tighten the brake cable adjuster locknut.
8. Slide the rubber cover to its original position.
9. Tighten the locknut at the brake lever.
Adjusting the brake pedal height
1. Brake cable adjuster locknut
2. Brake lever free play adjusting nut
3. Rubber cover
4. Distance B
(a)
(b)3
2
1
4
1. Brake pedal height
2. Brake pedal
3. Footboard1
23
UBB561E0.book Page 43 Monday, March 26, 2018 11:15 AM

8-44
8
Measure the brake pedal height and adjust if nec-
essary.
1. Remove the footboard by removing the quick fasteners, bolts, and nuts.
2. Loosen the locknut. 3. Turn the adjusting bolt in or out until the brake
pedal height is within the specified limits.
4. Tighten the locknut.
5. Install the footboard by installing the quick fasteners, bolts, and nuts, and then tighten
the bolts to the specified torques.
Brake pedal height:
80.0 mm (3.15 in)
1. Footboard
2. Quick fastener
3. Bolt and nut
4. Bolt
42
3
312
1. Locknut
2. Adjusting boltTightening torque:Locknut:7 N·m (0.7 kgf·m, 5.2 lb·ft)
2
1
UBB561E0.book Page 44 Monday, March 26, 2018 11:15 AM

8-46
8
Adjusting the brake pedal free play
Measure the brake pedal free play and adjust if
necessary.
TIPThe brake lever free play and brake pedal height
must be adjusted before adjusting the brake pedal
free play. 1. Loosen the locknut.
2. To increase the brake pedal free play, turn the
brake pedal free play adjusting nut in direc-
tion (a). To decrease the brake pedal free
play, turn the adjusting nut in direction (b).
3. Tighten the locknut.
EBU24231Axle bootsThe axle boots must be checked for damage at
the intervals specified in the periodic maintenance
and lubrication chart. Check the axle boots for
tears or damage. If any damage is found, have
them replaced by a Yamaha dealer.
1. Brake pedal free playBrake pedal free play: 20.0 mm (0.79 in)
1
1. Brake pedal free play adjusting nut
2. Locknut
21
(a)
(b)
UBB561E0.book Page 46 Monday, March 26, 2018 11:15 AM

8-47
8
EBU29882Brake light switchesThe brake light, which is activated by the brake
pedal and brake levers, should come on just be-
fore braking takes effect.
The rear brake light switch for the brake pedal can
be adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.
Turn the rear brake light switch adjusting nut while
holding the brake light switch in place. To make
the brake light come on earlier, turn the adjusting
nut in direction (a). To make the brake light come
on later, turn the adjusting nut in direction (b).
1. Front axle boot (each side)
1. Rear axle boot (each side)
1
1
1
1
1. Rear brake light switch
2. Rear brake light switch adjusting nut
12
(a)
(b)
UBB561E0.book Page 47 Monday, March 26, 2018 11:15 AM