2019 TOYOTA HIGHLANDER HYBRID ignition

21
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
Push
Turn
“Steering Lock active” will be displayed on the multi-information \
display.
Check that the shift lever is set in P. Press the power switch while tur\
ning the
steering wheel left and right.
Steering lock release
The “POWER” switch must be in the ACCESSORY or IGNITION ON/”ACC” or “ON”
position to be used.
Front
Front
Center console
Rear
USB charge-ports
(Charge only)
(Charge only)
Power outlets-12V DC
Power outlets-120V AC (if equipped)
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 218/13/18 4:18 PM

25
Seat heaters/ventilators
Hi temperature
OFF switch
Low temperature
Hi temperature
OFF switch
Low temperature
Turn the seat heater on and adjust the number, the higher the number, th\
e warmer
the seat becomes.
Driver’s seat
Driver’s seatFront
passenger’s seat
Front
passenger’s seat
Seat heaters/ventilators
Seat heatersOVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
Steering wheel-Heater (if equipped)
The “POWER” switch must be in the ACCESSORY or IGNITION ON position to be
used.
FRONT SEAT HEATERS AND VENTILATOR (IF EQUIPPED)
SECOND ROW SEAT HEATERS (IF EQUIPPED)
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 258/13/18 4:18 PM

32
CHANGING PCS ALERT TIMING
TOYOTA SAFETY SENSE™
FarMiddle
(default) Near
(1) Press “” switches and select from the Multi-Information Display (MID).
(2) Press “
” switches and select from the MID and then press “.”
(3) Select “Sensitivity” and then press “
.”
Each time “
” is pressed, the response to the PCS alert timing changes as shown
above. You can press “
” to go back to the menu.
Note: PCS is enabled each time the engine switch is turned to Ignition On.
The system can be disabled/enabled and the alert timing of the system can be
changed. (Alert timing only, brake operation remains the same).
Monocular camera sensor
Millimeter
wave radar
As part of the Pre-Collision System, this function is also designed to f\
irst provide an
alert and then automatic braking if needed.
Refer to a Toyota Owner’s Manual for additional limitations and infor\
mation.Under certain conditions, the PCS system included with the TSS-P package\
may
also help to detect a pedestrian in front of your vehicle using the in-v\
ehicle camera
and front-grill mounted millimeter wave radar. The in-vehicle camera of \
PCS
detects a potential pedestrian based on size, profile, and motion of the\
detected
pedestrian. However, a pedestrian may not be detected depending on the
conditions, including the surrounding brightness and the motion, posture\
, size, and
angle of the potential detected pedestrian, preventing the system from o\
perating or
engaging.
PCS PEDESTRIAN DETECTION
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 328/13/18 4:19 PM

33
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
(1) Press “” switches and select from the Multi-Information Display (MID).
(2) Press “
” switches and select the setting function from the MID and then
press “
”. The setting screen is displayed.
(3) Select
and then press “.” The Pre-Collision System will be disabled. You
can press “
” to go back to the menu.
Note: The system is enabled each time the engine switch is turned to Ignition
On.
LDA in TSS-P uses an in-vehicle camera designed to detect visible white \
and yellow
lane markers in front of the vehicle and the vehicle’s position on th\
e road. If the
system determines that the vehicle is starting to unintentionally deviat\
e from its lane,
the system alerts the driver with an audio and visual alert. When the al\
erts occur, the
driver must check the surrounding road situation and carefully operate t\
he steering
wheel to move the vehicle back to the center part of their lane.
LDA is designed to function at speeds of approximately 32 MPH or higher \
on
relatively straight roadways.
In addition to the alert function, LDA w/SA also features a steering assist
function. When enabled, if the system determines that the vehicle is on \
a path to
unintentionally depart from its lane, the system may provide small corrective steering
inputs to the steering wheel for a short period of time to help keep the\
vehicle in its
lane.
Lane Departure Alert with Steering Assist
(LDA w/SA)
DISABLING PRE-COLLISION SYSTEM (PCS)
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 338/13/18 4:19 PM

35
(1) Press “
” switches and select from the Multi-Information Display (MID).
(2) Press “
” switches and select the setting function and then press “”.
(3) Press “
” each time to change the setting.
(4) Press “
” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
ADJUSTING LDA ALERT SENSITIVITY
SWAY WARNING SYSTEM
SWS is a function of LDA and is designed to detect swaying based on the \
vehicle
location in the lane and the driver’s steering wheel operation. To he\
lp prevent
swaying, the system alerts the driver using a buzzer sound and a warning\
displays
in the MID.
Continuous lane deviations from
swaying.
Gentle swaying from driver’s
inattentiveness.
Acute steering wheel operation after the
number of operations decrease due to driver’s
inattentiveness.
DISABLING STEERING ASSIST
The driver can adjust the sensitivity of the LDA (warning) function from the
Multi-Information Display (MID) customization screen. High - Is designed to warn approximately before the front tire crosses the
lane marker.
Normal - (default) Is designed to warn approximately when the front tire
crosses the lane marker.
(1) Press “
” switches and select from the Multi-Information Display (MID).
(2) Press “
” switches and select the setting function and then press “”.
(3) Press “
” each time to change the setting. Press “” to go back to the menu.
OVERVIEW
FEATURES & OPERATIONS
TOYOTA SAFETY SENSE
SAFETY & EMERGENCY FEATURES
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 358/13/18 4:19 PM

36
(1) Press “” switches and select from the Multi-Information Display (MID).
(2) Press “
” switches and select the SWS setting function and then press “”.
(3) Press “
” each time to change the setting. Press “” to go back to the menu.
Note: Operation of the LDA system and setting adjustments continues in the
same condition regardless of Ignition cycle until changed by the driver or the
system is reset.
Dynamic Radar Cruise Control (DRCC)
TURNING SYSTEM ON/OFF
TOYOTA SAFETY SENSE™
(1)
DISABLING LDA SWAY WARNING SYSTEM
DRCC helps maintain a pre-set distance to a preceding vehicle when the p\
receding
vehicle is traveling at a lower speed. This mode is always selected firs\
t when the
cruise control button is depressed. Constant speed control mode is also \
available.
Push once: On
Push twice: Off
Refer to page 39 for switching to Constant Speed (Cruise) Control Mode\
.
Display Set speed
Indicators Dynamic Radar Cruise Control (DRCC)
vehicle-to-vehicle distance button
Cruise control switch
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 368/13/18 4:19 PM

40
TOYOTA SAFETY SENSE™
When all of these conditions are met, high beams will be automatically t\
urned on
(after approximately 1 second):• Vehicle speed is above approximately 21 mph (34 km/h).
• The area ahead of the vehicle is dark.
• There are no oncoming or preceding vehicles with headlights or tail\
lights turned on.
• There are few street lights on the road ahead.
If any of these conditions occur, the system is designed to automaticall\
y turn off
high beams: • Vehicle speed drops below approximately 17 mph (27 km/h).
• The area ahead of the vehicle is not dark.
• Oncoming or preceding vehicles have headlights or tail lightsturned on.
• There are many streetlights on the road ahead.
CONDITIONS WHERE AHB WILL TURN ON/OFF AUTOMATICALLY
(1) With the engine switch in IGNITION ON mode and headlight switch turned to “AUTO” or “
”position, push lever away from you.
(2) Press the “
” switch.
The “
” indicator will come on when the headlights are turned on
automatically to indicate that the system is active.
Note: Pull the lever back toward you to turn the AHB system off.
The AHB indicator will turn off. To turn switch to “
” position and the manual
high beam indicator “
” turns on.
ACTIVATING THE AHB SYSTEM
Automatic High Beams (AHB)
AHB is a safety system designed to help drivers see more of what’s ah\
ead at
nighttime and reduce glare for oncoming drivers. When enabled, AHB uses \
an
in-vehicle camera to help detect the headlights of oncoming vehicles and\
tail lights
of preceding vehicles, then automatically switches between high and low \
beams
as appropriate to provide the most light possible and enhance forward vi\
sibility.
By using high beams more frequently, the system may allow earlier detect\
ion of
pedestrians and obstacles.
Refer to the Toyota Owner’s Manual for additional information on AHB \
operation,
settings adjustments, limitations, and precautions before attempting to \
use it.
(2) (1)
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 408/13/18 4:19 PM

42
SAFETY & EMERGENCY FEATURES
Unlock
Lock
Rear door child safety locks
Tire Pressure Monitoring (warning) System (TPMS)
Moving the lever to the lock position will allow the door to be opened o\
nly from the
outside
Rear door
System reset initialization
1. Push and hold “
SET” button
until the indicator blinks three times.
2. Wait a few minutes to allow initialization to complete.
After adjusting tire pressures, or after tires have been rotated or repl\
aced, turn the
ignition switch to “ON” and press and hold the
“ SET” button until indicator blinks
three times. Let the vehicle sit for a few minutes to allow initializati\
on to complete.
Refer to the load label on the door jamb or the Owner’s Manual for ti\
re inflation
specifications.
If the tire pressure indicator flashes for more than 60 seconds and then\
remains on,
take the vehicle to your local Toyota dealer.
NOTE: The warning light may come on due to temperature changes or changes
in tire pressure from natural air leakage. If the system has not been initialized
recently, setting the tire pressures to factory specifications should turn off the
light.
49193b_MY19_Highlander_HV_QRG_V3_ML_0809.indd 428/13/18 4:19 PM