2019 TOYOTA AYGO warning lights

962. Instrument cluster
AYGO_OM_Europe_OM99R19E
Warning lights and indicators
Vehicles without a tachometer
Vehicles with a tachometer
The warning lights and indicators on the instrument cluster and
center panel inform the driver of the status of the vehicle’s vari-
ous systems.
For the purpose of explanation, the following illustration dis-
plays all warning lights and indicators illuminated.

972. Instrument cluster
2
Instrument cluster
AYGO_OM_Europe_OM99R19E
Warning lights inform the driver of malfunctions in the indicated vehi-
cle’s systems.
Warning lights
*1Brake system warning
light ( P. 417)
*1Electric power steering
system warning light
( P. 419)
*1
Charging system
warning light ( P. 417)
*1, 2, 4
PCS warning light
( P. 420)
*1
Low engine oil pressure
warning light ( P. 417)
*2, 3
(Yellow)
Speed limiter indicator
( P. 420)
*1High engine coolant
temperature warning
light ( P. 417)
*1, 2, 4
Stop & Start cancel
indicator ( P. 420)
*1“STOP” warning light
( P. 418)
*1
Slip indicator light
( P. 421)
*1, 2Multi-mode manual
transmission
warning light ( P. 418)
*2
(Yellow)
LDA indicator (P. 421)
*1, 2, 4
Heat clutch warning light
( P. 418)
*2, 7
(Yellow)
Lane marker indicators
( P. 421)
*1
Malfunction indicator
lamp ( P. 419)
*2, 5
(Yellow)
Smart entry & start
system indicator light
( P. 421, 425)
*1SRS warning light
( P. 419)
Open door warning light
( P. 421)
*1
ABS warning light
( P. 419)
Driver’s and front pas-
senger’s seat belt
reminder light ( P. 421)

982. Instrument cluster
AYGO_OM_Europe_OM99R19E
*1: These lights turn on when the engine switch is turned to the “ON” position
(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system), to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or turn off. Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer.
*2: If equipped
*3: The light comes in yellow to indicate a malfunction.
*4: The light flashes to indicate a malfunction.
*5: The light flashes in yellow to indicate a malfunction. The light flashes
quickly in green to indicate that the steering lock has not been released.
*6: This light illuminates on the center panel.
*7: The lights turn on with LDA indicator to indicate a malfunction.
The indicators inform the driver of the operating state of the vehicle’s
various systems.
*6Rear passengers’ seat
belt reminder lights
( P. 421)
*1, 2
Tire pressure warning
light ( P. 422)
Low fuel level warning
light ( P. 422)
Indicators
*1Gear Shift indicator
( P. 192, 195)
Headlight high beam
indicator ( P. 200)
Turn signal indicator
( P. 197)
*2Front fog light indicator
( P. 203)
*2
(Green)
Smart entry & start
system indicator light
( P. 185)
Rear fog light indicator
( P. 203)
Tail light indicator
( P. 199)
*1, 3Slip indicator light
( P. 248)

992. Instrument cluster
2
Instrument cluster
AYGO_OM_Europe_OM99R19E
*1: These lights turn on when the engine switch is turned to the “ON” position(vehicles without a smart entry & start system) or IGNITION ON mode
(vehicles with a smart entry & start system), to indicate that a system check
is being performed. They will turn off after the engine is started, or after a
few seconds. There may be a malfunction in a system if a light does not
come on, or turn off. Have the vehicle inspected by any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer.
*2: If equipped
*3: The light flashes to indicate that the system is operating.
*4: This light illuminates on the center panel.
*5: The light comes on when the system is turned off.
*6: The light comes on when system settings are changed.
*7: The light flashes in yellow to indicate that the vehicle is deviating from thelane.
*1VSC off indicator
(P. 248)*1, 2Stop & Start cancel
indicator ( P. 241)
*2
(Green)
Speed limiter indicator
light (P. 237)*1, 2
“TRC OFF” indicator
(P. 248)
*2
(Green)
LDA indicator ( P. 232)
*2, 3, 6
PCS activation indicator
(P. 219, 222)
*2, 7
(Green)
Lane marker indicators
(P. 233)*1, 2, 5
PCS warning light
( P. 222)
*1, 2
Stop & Start indicator
light ( P. 240)
“PASSENGER AIR BAG” indicator
( P. 4 7 )
*1, 4

1313-2. Opening, closing and locking the doors
3
Operation of each component
AYGO_OM_Europe_OM99R19E
■ Alarms and warning indicators
A combination of exterior and interior alarms as well as warning lights are
used to prevent theft of the vehicle and unforeseeable accidents resulting
from erroneous operation. Take appropria te measures for the warning light
that comes on. ( P. 425)
The following table describes circumstances and correction procedures when
only alarms are sounded.
AlarmSituationCorrection procedure
Exterior alarm sounds
once for 5 seconds
An attempt was made
to lock the doors using
the smart entry & start
system while the elec-
tronic key was still
inside the vehicle.
Retrieve the electronic
key from the vehicle
and lock the doors
again.
An attempt was made
to lock the vehicle while
a door was open.
Close all of the doors
and lock the doors
again.
Interior alarm pings
once and exterior alarm
sounds once for 5 sec-
onds
An attempt was made
to lock any door by
opening a door and
putting the inside lock
button into the lock
position, then closing
the door by pulling on
the outside door handle
with the electronic key
still inside the vehicle.
Retrieve the electronic
key from the vehicle
and lock the doors
again.
Interior alarm sounds
continuously
The engine switch was
turned to ACCESSORY
mode while the driver’s
door was open (or the
driver’s door was
opened while the
engine switch was in
ACCESSORY mode).
Turn the engine switch
off and close the
driver’s door.
The engine switch was
turned to off while the
driver’s door was open.
Close the driver’s door.

1603-4. Adjusting the steering wheel and mirrors
AYGO_OM_Europe_OM99R19E
Inside rear view mirror
The height of the rear view mirror can be adjusted to suit your driving
posture.
Adjust the height of the rear view
mirror by moving it up and down.
Reflected light from the headlights of vehicles behind can be reduced
by operating the lever.
Normal position
Anti-glare position
The rear view mirror’s position can be adjusted to enable suffi-
cient confirmation of the rear view.
Adjusting the height of rear view mirror (if equipped)
Anti-glare function
1
2
WARNING
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident,
resulting in death or serious injury.

2064-3. Operating the lights and wipers
AYGO_OM_Europe_OM99R19E
■The windshield wiper and washer can be operated when
Vehicles without a smart entry & start system
The engine switch is in the “ON” position.
Vehicles with a smart entry & start system
The engine switch is in IGNITION ON mode.
■ If no windshield washer fluid sprays
Check that the washer nozzles are not blocked, if there is washer fluid in the
windshield washer fluid reservoir.
WARNING
■ Caution regarding the use of washer fluid
When it is cold, do not use the washer fluid until the windshield becomes
warm. The fluid may freeze on the windshield and cause low visibility. This
may lead to an accident, resulting in death or serious injury.
NOTICE
■ When the windshield is dry
Do not use the wiper, as they may damage the windshield.
■ When the washer fluid tank is empty
Do not operate the switch continually as the washer fluid pump may over-
heat.
■ To prevent battery discharge
Do not leave the wiper on longer than necessary when the engine is off.

2184-5. Toyota Safety Sense
AYGO_OM_Europe_OM99R19E
WARNING
●If the area of the windshield in front of the front sensor is covered with
water droplets, use the windshield wipers to remove them.
If the water droplets are not sufficiently removed, the performance of the
front sensor may be reduced.
● If water droplets cannot be properly removed from the area of the wind-
shield in front of the front sensor by the windshield wipers, replace the
wiper insert or wiper blade.
If the wiper inserts or wiper blades need to be replaced, contact any autho-
rized Toyota retailer or Toyota authorized repairer, or any reliable repairer.
● Do not attach window tinting to the windshield.
● Replace the windshield if it is damaged or cracked.
If the windshield needs to be replaced, contact any authorized Toyota
retailer or Toyota authorized repairer, or any reliable repairer.
● Do not install an antenna in front of the sensor.
● Do not get the front sensor wet.
● Do not allow bright lights to shine into the front sensor.
● Do not dirty or damage the front sensor.
When cleaning the inside of the windshi eld, do not allow glass cleaner to
contact the lens. Also, do not touch the lens.
If the lens is dirty or damaged, contact any authorized Toyota retailer or
Toyota authorized repairer, or any reliable repairer.
● Do not subject the front sensor to a strong impact.
● Do not change the installation position or direction of the front sensor or
remove it.
● Do not disassemble the front sensor.
● Do not install an electronic device or device that emits strong electric
waves near the front sensor.
● Do not modify any components of the vehicle around the front sensor
(inside rear view mirror, sun visors, etc.) or ceiling.
● Do not attach any accessories that may obstruct the front sensor to the
hood, front grille or front bumper. C ontact any authorized Toyota retailer or
Toyota authorized repairer, or any reliable repairer for details.
● If a surfboard or other long object is to be mounted on the roof, make sure
that it will not obstruct the front sensor.
● Do not modify the headlights or other lights.
● Do not attach anything to or place anything on the dashboard.
■ Installation area of front sensor on windshield
When the windshield is fogging up easily, the glass around the front sensor
may be hot due to the heater running. If the glass is touched, it may result in
burns.