2019 Peugeot 208 screen wash

56
Automatic rain sensitive
windscreen wipers
The windscreen wipers operate
automatically, without any action
on the part of the driver, when rain
is detected (sensor behind the rear
view mirror), adapting their speed to
the intensity of the rainfall.
Switching on
This indicator lamp comes on in the
instrument panel and a message is
displayed.
Give a

short downwards push to the control
stalk.
A wiping cycle confirms that the instruction has
been accepted.
Switching off
This indicator lamp goes off in the
instrument panel and a message is
displayed.
Give another short downwards push to
the control stalk or shift the control stalk to
a

different position (Int, 1 or 2). If the wipers operate in intermittent mode
when in AUTO mode, have the system
checked by a
PEUGEOT dealer or
a

qualified workshop.
Do not cover the rain sensor, combined with
the sunshine sensor, located at the top of
the windscreen behind the rear view mirror.
When using an automatic car wash, switch
off the automatic rain sensitive wipers.
In winter, it is advisable to wait until the
windscreen is completely clear of ice before
activating the automatic rain sensitive
wipers.
Front screenwash
Pull the wiper control stalk towards you. The
screenwash and then the wipers operate for
a
preset time.
Front wipers
Fast (heavy rain).
Normal (moderate rain).
Intermittent (proportional to the
speed of the vehicle).
Of f.
Single wipe (press down and
release). The automatic rain sensitive windscreen
wipers must be reactivated by pushing the
control stalk downwards, if the ignition has
been off for more than 1
minute.
Lighting and visibility

57
Changing a wiper blade
This position permits release of the windscreen
wiper blades.
It is used for cleaning or replacing the wiper
blades. It can also be useful, in winter, to
release the wiper blades from the windscreen.
To move the wiper blades to the vertical position:
F O perate the wiper control stalk within one
minute after switching off the ignition to
position the wiper blades vertically on the
windscreen.
To return them to the park position:
F

S
witch on the ignition and operate the wiper
control stalk.
Removing a wiper blade
F Lift the corresponding wiper arm.
F U nclip and remove the wiper blade.
Fitting a new wiper blade
F Put the corresponding new wiper blade in place and clip it.
F

F
old down the wiper arm carefully. To maintain the effectiveness of the wiper
blades, it is advisable to:
-

h
andle them with care,
-
c
lean them regularly using soapy water,
-
a
void using them to retain cardboard on the
windscreen,
-
r
eplace them at the first signs of wear.
Rear wiper
Of f.
Intermittent wipe.
Wash-wipe (set duration).
If a

significant accumulation of snow or ice
is present, or when using a
bicycle carrier
on the boot, deactivate the automatic rear
wiper via the vehicle configuration menu
on the touch screen.
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen wiper
is operating.
The activation or deactivation of
operation of the rear wiper when
engaging reverse gear can be set in
the Driving/Vehicle menu.
4
Lighting and visibility

97
allow the driver time to take back control of
the vehicle,
-

m
ay cause the engine to stall,
-

m
ay give rise to a pumping noise, due to the
pressurisation of the braking system.
The collision can be automatically avoided
if the speed difference between your
vehicle and the one ahead is not more
than 9
mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
impact by lowering the speed of impact.
Activation/Deactivation
It is possible to activate or
deactivate the Active City Brake
from the Driving/Vehicle menu.
The system state remains memorised when the
ignition is switched off.
Each subsequent time the ignition is switched
on, if the automatic emergency braking function
is deactivated, a temporary message will
be displayed to point this out when a
speed
threshold (6
mph (10 km/h)) is exceeded. Deactivate the Active City Brake:
-

F
ollowing an impact to the windscreen
close to the sensor.
-
W
hen towing a trailer.
-
W
hen the vehicle is being towed.
-
W
hen the vehicle is about to cross
a toll barrier.
-
W
hen the vehicle is passing through
an automatic car wash.
Operating limits
Not detected are:
- Pe destrians, animals, motorcyclists,
cyclists.
-

F
ixed and non-reflective materials and
objects (cardboard box, wall, etc.).
-

V
ehicles not travelling in the same direction.
This system will not trigger or inter vene if the
driver:
-

p
resses the accelerator pedal firmly,
-

t
urns the wheel sharply (avoiding
manoeuvre).
Operating faults
Clean or clear any dirt, mist or objects (stickers,
leaves, etc.) from the top of the windscreen that
could obstruct the laser's field of vision. In the following cases, you should have the
system checked by a
PEUGEOT dealer or
a

qualified workshop:
-
T
he message "
Automatic braking system
fault " accompanied by an audible signal
indicates that a fault has been detected.
-
F
ollowing an impact, the system is
automatically put out of ser vice, it no longer
works. The system detects the deployment
of airbags.
Do not attempt to remove, adjust or test
the sensor.
Only a PEUGEOT dealer or a qualified
workshop is able to work on the system.
Misting of the windscreen or accumulations
of snow on the bonnet could inter fere with the
operation of the laser. A message appears if
the laser is obstructed.
Use windscreen demisting and regularly clean
the area of the windscreen in front of the
sensor.
Be particularly vigilant when driving in poor
weather (very heavy rain, hail, fog, snow, etc.).
This is because braking distances increase
while the laser's calculation parameters remain
the same.
6
Driving

99
Deactivation/activation of the
front and rear parking sensors
Without touch screen
F To deactivate or activate the system, press this button.
The indicator lamp is illuminated when the
system is deactivated.
The deactivation or activation of
the function is done in the Driving/
Vehicle menu.
The function will be deactivated
automatically if a
trailer is being towed
or a
bicycle carrier is fitted (vehicle fitted
with a
towing device or bicycle carrier
recommended by PEUGEOT).
Operating limits
- Certain obstacles located in the sensors' blind spots may not be detected or no
longer be detected during the manoeuvre.
-

S
ounds such as those emitted by noisy
vehicles and machinery (e.g. lorries,
pneumatic drills, etc.) may inter fere with the
vehicle's sensors.
-

C
ertain materials (fabrics) absorb sound
waves: pedestrians may not be detected.
-

A
ccumulated snow or dead leaves on the
road sur face can inter fere with the vehicle's
sensors.
-

A f
ront or rear impact to the vehicle can
distort the settings of the sensors, which is
not always detected by the system: distance
measurements may be incorrect.
-

T
he tilting of the vehicle if the boot is
very loaded can affect the distance
measurements.
-

T
he sensors may be affected by poor
weather conditions (heavy rain, thick fog,
snowfall, etc.).
Maintenance
recommendations
In bad or wintry weather, ensure that the
sensors are not covered with mud, ice or
snow. When reverse gear is engaged, an
audible signal (long beep) indicates that
the sensors may be dirty.
High-pressure jet wash
When washing your vehicle, keep the
lance at least 12
inches (30 cm) away from
the sensors.
Operating fault
If a fault occurs when shifting
t o reverse, this warning lamp
comes on in the instrument panel,
accompanied by a
message and an
audible signal (short beep).
Contact a
PEUGEOT dealer or a qualified
workshop to have the system checked.
With touch screen
6
Driving

100
Reversing camera
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed on the touch screen.
The reversing camera function may be
supplemented with parking sensors.
The superimposed representation of guide
lines helps with the manoeuvre.
They are represented as lines marked "on the
ground" and do not indicate the position of the
vehicle in relation to tall obstacles (e.g. other
vehicles).
Some distortion of the image is normal.
The blue lines 1 represent the general direction of
t he vehicle (the distance between them represents
the width of your vehicle without the door mirrors).
The red line 2
represents a distance of about
30
cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines 3
represent distances of about
1
and 2 metres beyond the edge of your vehicle's
rear bumper.
The reversing camera cannot, in any circumstances,
replace the need for vigilance on the part of the driver.
High-pressure jet wash
When washing your vehicle, do not direct
the lance from less than 30
cm from the
lens of the camera.
Opening the tailgate causes the display to
disappear.
Clean the reversing camera regularly
using a
soft, dry cloth.
Park Assist
The system detects a parking space and then
p rovides assistance with the parallel parking
manoeuvres.
The Park Assist system cannot in any
circumstances replace the need for vigilance on
the part of the driver.
The driver must remain in control of their vehicle
ensuring that the space remains clear during the
manoeuvre.
In some circumstances, the sensors may not
detect small obstacles located in their blind spots.
During manoeuvring phases, the steering
wheel per forms rapid turns: do not hold
the steering wheel, do not put your hands
between the spokes of the steering wheel.
Watch out for any object that could block
the manoeuvre (loose clothing, scar ves,
ties, etc.) – Risk of injury!
It controls the steering and provides visual and
audible information to the driver.
If you have a
manual gearbox, the driver
manages the acceleration, braking, gears and
clutch.
With an automatic gearbox, the driver manages
the acceleration, braking and gears.
The driver can take control at any time by
gripping the steering wheel.
Driving

112
Engines
Petrol
Diesel
These engines are examples provided as
a guide.
The locations of the following elements may
vary:
-

A
ir filter.
-

E
ngine oil dipstick.
-

E
ngine oil filler cap.
-
P

riming pump. 1.
Screenwash fluid tank.
2. Coolant tank.
3. Brake fluid tank.
4. Battery.
5. Fusebox.
6. A i r f i l t e r.
7. Engine oil dipstick.
8. Engine oil filler cap.
9. Remote earth point.
10. Priming pump*
The Diesel circuit is under very high
pressure.
All work on this circuit must be carried out
only by a PEUGEOT dealer or a qualified
workshop.
Checking levels
Check all of these levels regularly, in line with
the manufacturer's service schedule. Top them
up if necessary, unless other wise indicated.
If a
level drops significantly, have the
corresponding system checked by a
PEUGEOT
dealer or a
qualified workshop.
The liquid must comply with the
manufacturer's recommendations and with
the vehicle's engine. Take care when working under the bonnet,
as certain areas of the engine may be
extremely hot (risk of burns) and the
cooling fan could start at any time (even
with the ignition off).
Used products
Avoid prolonged contact of used oil or
fluids with the skin.
Most of these fluids are harmful to health
or indeed very corrosive.
Do not discard used oil or fluids into
sewers or onto the ground.
Take used oil to a
PEUGEOT dealer or
a
qualified workshop and dispose of it in
the containers reser ved for this purpose.
Engine oil level
The check is carried out either when
the ignition is switched on using the
oil level indicator in the instrument
panel for vehicles equipped with an
electric gauge, or using the dipstick.
*
D

epending on engine.
Practical information

114
Coolant level
Check the coolant level regularly.
It is normal to top up the fluid
between two services.
The check and top-up must only be done with
the engine cold.
A low coolant level presents a
risk of serious
damage to your engine.
The coolant level should be close to the "MA X"
mark but should never exceed it.
If the level is close to or below the "MIN" mark,
it is essential to top up.
When the engine is hot, the temperature of the
coolant is regulated by the fan.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying out any
work.
To avoid the risk of scalding when you need to
top up in an emergency, wrap a
cloth around
the cap and unscrew the cap by two turns to
allow the pressure to drop.
Once the pressure has dropped, remove the
cap and top up to the required level.
The cooling fan may star t after
switching off the engine: take care
with articles and clothing that might be
caught by the fan blades.
Screenwash fluid level
Top up to the required level when
necessary.
Fluid specification
The screenwash fluid must be topped up with
a ready for use mix.
In winter (temperatures below zero), a fluid with
antifreeze must be used that is appropriate for
the prevailing conditions, in order to preser ve
the elements of the system (pump, tank, ducts,
e t c .) .
Filling with pure water is prohibited under all
circumstances (risk of freezing, limestone
deposits, etc.).
Diesel fuel additive level
(Diesel with particle filter)
The additive reser voir low level is
indicated by fixed illumination of this
warning lamp, accompanied by an
audible signal and a
message that
the particle filter additive level is
too low.
To p p i n g u p
This additive must be topped up without delay
by a PEUGEOT dealer or a qualified workshop.
Level of AdBlue
An alert is triggered once the reser ve level is
reached.
To avoid the vehicle being immobilised as per
regulations, you must top up the AdBlue tank.
For more information on AdBlue (BlueHDi
engines), and in particular on topping up the
tank, refer to the corresponding section.
Checks
Unless otherwise indicated, check these
components in accordance with the
manufacturer's service schedule and according
to your engine.
Other wise, have them checked by a
PEUGEOT
dealer or a
qualified workshop.
12 V battery
The battery does not require any
maintenance.
However, check regularly that the
terminals are correctly tightened
(versions without quick release terminals)
and that the connections are clean.
Practical information

135
PEUGEOT accepts no responsibility for
the cost incurred in repairing your vehicle
or for rectifying malfunctions resulting
from the installation of accessories
not supplied and not recommended by
PEUGEOT and not installed in accordance
with specifications, in particular when the
combined power consumption of all of the
additional equipment connected exceeds
10

milliamperes.
Left-hand side
Fuse N° Rating Functions
F2 5
ADoor mirrors,
headlamps,
diagnostic socket.
F9 5
AAlarm.
F10 5
AIndependent
telematic unit, trailer
interface unit.
F11 5
AElectrochrome
interior rear view
mirror, additional
heating.
F13 5
AHi-Fi amplifier,
parking sensors.
F16 15


AFront 12
V socket.
F17 15


AAudio system, audio
system (accessory).
F18 20
ATouch screen. Fuse N°
Rating Functions
F23 5
AVanity mirrors, map
reading lamps.
F26 15


AHorn.
F27 15


AScreenwash pump.
F28 5
AAnti-theft.
F29 15


AAir conditioning
compressor.
F30 15


ARear wiper.
8
In the event of a breakdown