2019 Peugeot 208 engine

23
Remaining range less than 60 miles
( 100 km) (1.5 BlueHDi Euro 6.2)
When driving, the audible signal and the
message display are triggered every 6
miles
(10
km) until the AdBlue tank is topped up.
It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
Breakdown related to a
lack of AdBlue
®
The AdBlue® tank is empty: the starting
prevention system required by legislation
prevents starting of the engine. It is essential to top up as soon as possible and
before the tank is completely empty; other wise
it will not be possible to restart the engine after
the next stop.
When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal (1

beep) and the display of a message
("Top up AdBlue: Starting impossible in
x miles") indicating the remaining range
expressed in miles or kilometres.
When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal and the display of the message "Top up
AdBlue: Starting impossible". To be able to restart the engine, it is
essential to add at least 5 litres of AdBlue
®
to its tank.
For more information on AdBlue
®
(BlueHDi engines) , and, in particular,
on topping up, refer to the corresponding
section.
In the event of a fault with the
S CR emissions control system
A system that prevents engine starting is
activated automatically from 685
miles
(1,100
km) after confirmation of a fault with
the SCR emissions control system.
Have the system checked by a
PEUGEOT
dealer or a
qualified workshop as soon as
possible.
In the event of the detection of a
faultIf it is a
temporary fault, the alert
disappears during the next journey, after
self-diagnosis of the SCR system.
During the permitted driving phase
(between 685 and 0 miles (1,100 and 0 km))
These warning lamps come on, accompanied
by an audible signal and the display of the
message "Emissions fault".
The alert is triggered when driving when the
fault is detected for the first time, then when switching on the ignition for subsequent
journeys, while the fault persists.
If a
fault with the SCR system is confirmed
(after 31
miles (50 km) covered with the
permanent display of the message signalling
a
fault), these warning lamps come on and the
AdBlue warning lamp flashes, accompanied by
an audible signal and the display of a
message
(e.g. "Emissions fault: Starting prevented in
185
miles") indicating the remaining range in
miles or kilometres.
While driving, the message is displayed every
30
seconds while the fault with the SCR
emissions control system persists.
The alert is repeated when switching on the
ignition.
You should go to a
PEUGEOT dealer or
a
qualified workshop as soon as possible.
Other wise you will not be able to restart the
vehicle.
1
Instruments

24
Starting preventedYou have exceeded the authorised driving
limit: the starting prevention system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a
PEUGEOT dealer or a qualified workshop.
Each time the ignition is switched on, these
warning lamps come on and the AdBlue
warning lamp flashes, accompanied by an
audible signal and the display of the message
"Emissions fault: Starting prevented".
Trip computer
Instrument panel screen
F Each press on the end of the wiper
control stalk displays the information in
turn. -
Trip
1 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the first trip.
- Trip
2 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the second trip.
-
T
he current information with:
•
t
he range,
•
t
he current fuel consumption,
•
t
he Stop & Start time counter.
With touch screen
The information is accessible via the
Driving/Vehicle
.
Reset trip
F When the desired trip is displayed, press
the button located on the end of the wiper
control stalk for more than 2
seconds.
Trips 1
and 2 are independent and are used
identically.
For example, trip 1
can be used for daily figures
and trip 2
for monthly figures.
Display of information on the touch screen
Instruments

29
When the vehicle is locked, if it is
unlocked without the opening of a door
or the boot, it will automatically lock itself
again after thirty seconds.
Locating your vehicle
F A press switches on the vehicle's lighting and flashes the direction
indicators for a
few seconds to
help you locate your vehicle.
Guide-me-home lighting
Make a long press on this button to
o perate the guide-me-home lighting
(switching on the sidelamps, dipped
beams and number plate lamps).
A second press before the end of the timed
period cancels the guide-me-home lighting.
Deadlocking
Deadlocking deactivates the exterior and
interior door controls as well as the central
locking button on the dashboard.
You must therefore never leave anyone
inside the vehicle when it is deadlocked.
With the key
F Turn the key to the rear in the driver's door lock.
F

T
urn the key to the rear again within
5
seconds to deadlock the vehicle.
With the remote control
F Press this button once to lock the vehicle fully.
F

P
ress this button again within
5
seconds to deadlock the
vehicle.
Deadlocking is confirmed by fixed
lighting of the direction indicators for
approximately 2


seconds.
Depending on the version you have, the
electric door mirrors fold at the same time.
Advice
Remote control
The high frequency remote control is
a
sensitive system; do not operate it while
it is in your pocket as there is a
possibility
that it may unlock the vehicle, without you
being aware of it.
Do not press the buttons of your remote
control out of range and out of sight of
your vehicle. It might stop working. It will
then be necessary to reinitialise it again.
The remote control does not operate when
the key is in the ignition, even when the
ignition is switched off.
Anti-theft protection
Do not make any modifications to the
electronic engine immobiliser system; this
could cause malfunctions.
For vehicles with an ignition switch, do
not forget to remove the key and turn the
steering wheel to engage the steering
lock.
The automatic folding and unfolding of the
door mirrors can be deactivated via the
vehicle's configuration menu.
2
Access

32
Reinitialising the remote
control
Following replacement of the battery or in
the event of a remote control fault, it may be
necessary to reinitialise the remote control.
F

S
witch off the ignition.
F

T
urn the key to position 2

(Ignition on).
F

P
ress the closed padlock button for a few
seconds.
F

S
witch off the ignition and remove the key
from the switch.
The remote control is now fully operational
again.
Boot
Opening
F After unlocking the boot or the vehicle using the remote control or the key, press
the opening control, then raise the tailgate.
Closing
F Lower the tailgate using the interior grab handle.
F

I
f necessary, press down on the tailgate to
fully close it.
If the tailgate is not fully closed:
-

w
ith the engine running ,
this warning lamp comes on,
accompanied by the display of an
alert message for a
few seconds,
-

w
hen driving (speed above 6
mph
(10
km/h)), this warning lamp comes on,
associated with an audible signal and
the display of an alert message for a
few
seconds. In the event of a
fault or difficulties felt in
manoeuvring the tailgate when opening
or closing it, have it quickly checked
by a PEUGEOT dealer or a qualified
workshop to stop this issue getting worse
and so as to not cause the tailgate to drop,
and serious injuries.
Backup control
System for mechanical unlocking of the boot in
the event of a central locking malfunction.
Unlocking
F Fold the rear seats to gain access to the lock from inside the boot.
F

I
nsert a small screwdriver into hole A of the
lock to unlock the boot.
F

M
ove the latch to the left.
Access

39
Heated seats
F With the engine running, use the control wheel to switch on and select the level of
heating required:
0: Of f.
1: Low.
2: Medium.
3: High.
Do not use the function when the seat is
not occupied.
Reduce the intensity of the heating as
soon as possible.
When the seat and passenger
compartment have reached an adequate
temperature, you can stop the function;
reducing the consumption of electrical
current reduces fuel consumption. Prolonged use at the highest setting is
not recommended for those with sensitive
skin.
There is a
risk of burns for people whose
perception of heat is impaired (illness,
taking medication, etc.).
There is a risk of overheating the system if
material with insulating properties is used,
such as cushions or seat covers.
Do not use the system:
- i f wearing damp clothing,
-

i
f child seats are fitted.
To avoid breaking the heating element in
the seat:
-

d
o not place heavy objects on the seat,
-

d
o not kneel or stand on the seat,
-

d
o not place sharp objects on the seat,
-

d
o not spill liquids onto the seat.
To avoid the risk of short-circuit:
-

d
o not use liquid products for cleaning
the seat,
-
n

ever use the heating function when
the seat is damp.
Armrest
Cover with opening lever
F

L
ift the lever to raise the cover.
Storage space in the console
F

P
ull the armrest fully up.
3
Ease of use and comfort

41
Returning the backrest to
the normal position
F Raise the seat backrest 2.
F L atch the backrest in place, the red indicator
in the control 1
is no longer visible.
F

U
nbuckle and reposition the seat belts
ready for use.
F

R
efit the head restraint(s).
When folding the seat, the centre seat belt
should not be fastened but laid out flat
along the seat.
When repositioning the seat backrest,
take care not to trap the seat belts.
The rear seat cushion does not fold, only
the seat backrest can be folded in order to
increase the boot loading space.
Head restraints
These have a position for use (up) and
a stowed position (down).
They can be removed and are interchangeable
side to side.
To remove a
head restraint:
F

p
ull the head restraint fully upwards,
F

t
hen, press lug A .
Never drive with the head restraints
removed; they must be fitted and correctly
adjusted.
Advice
Using the ventilation and air
conditioning system
F

T
o ensure that the air is distributed
evenly, keep the external air intake
grilles at the base of the windscreen,
the nozzles, the vents, the air outlets
and the air extractor in the boot free
from obstructions.
F

D
o not cover the sunshine sensor,
located on the dashboard; this is used
for regulation of the automatic air
conditioning system.
F

O
perate the air conditioning system for
at least 5
to 10 minutes, once or twice
a
month to keep it in per fect working
o r d e r.
F

I
f the system does not produce cold air,
switch it off and contact a
PEUGEOT
dealer or a
qualified workshop.
When towing the maximum load on
a
steep gradient in high temperatures,
switching off the air conditioning increases
the available engine power and so
improves the towing ability.
3
Ease of use and comfort

42
If after an extended stop in sunshine, the
interior temperature is very high, first air
the passenger compartment for a few
moments.
Put the air flow control at a
setting high
enough to quickly change the air in the
passenger compartment.
The condensation created by the air
conditioning results in a discharge of water
under the vehicle which is per fectly normal.
Servicing the ventilation and air
conditioning system
F

E
nsure that the cabinfilter is in good
condition and have the filter elements
replaced regularly.
We recommend the use of a
combined
cabin filter. Thanks to its special active
additive, it contributes to the purification of
the air breathed by the occupants and the
cleanliness of the passenger compartment
(reduction of allergic symptoms, bad odours
and greasy deposits).
F

T
o ensure correct operation of the
air conditioning system, you are also
advised to have it checked regularly
as recommended in the Warranty and
Maintenance Record.
Stop & Star t
The heating and air conditioning systems
only work when the engine is running.
Temporarily deactivate the Stop &
Start system to maintain a
comfortable
temperature in the passenger
compartment.
For more information on Stop & Star t ,
refer to the corresponding section.
Heating
1. Temperature adjustment.
2. Air flow adjustment.
3. Air distribution adjustment.
4. Recirculation of interior air.
Temperature
F Turn the knob 1 from blue (cold) to red (hot)
to adjust the temperature.
Air flow
F Turn the knob 2 from position "1" to position
" 6 " to obtain the desired air flow for your
comfort.
If you place the air flow control at position
" 0
"(off), the temperature in the vehicle
will no longer be maintained. A slight flow
of air can still be felt, resulting from the
for ward movement of the vehicle.
Air distribution
You can vary the air distribution in the
passenger compartment using the knob 3 .
Windscreen and side windows.
Windscreen, side windows and
footwells.
Footwells.
Central and side vents.
The air distribution can be
modulated by placing the knob at an
intermediate position.
Ease of use and comfort

43
Manual air conditioning
1.Temperature adjustment.
2. Air flow adjustment.
3. Air distribution adjustment.
4. Recirculation of interior air.
5. Air conditioning on/off.
Dual-zone automatic air
conditioning
Temperature
F Turn the knob 1 from blue (cold) to red (hot)
to adjust the temperature.
Air flow
F Turn the knob 2 from position "1" to position
" 6 " to obtain the desired air flow for your
comfort.
If you place the air flow control at position
" 0
"(off), the temperature in the vehicle
will no longer be maintained. A slight flow
of air can still be felt, resulting from the
for ward movement of the vehicle.
Air distribution
You can vary the air distribution in the
passenger compartment using the knob 3 .
Windscreen and side windows.
Windscreen, side windows and
footwells.
Footwells.
Central and side vents.
The air distribution can be
modulated by placing the knob at an
intermediate position.
Air conditioning
With the engine running, the air conditioning is
designed to operate effectively in all seasons,
with the windows closed.
It allows you:
-

i
n summer, to lower the temperature,
-

t
o increase the effectiveness of the
demisting in winter, above 3°C.
On/Off
F Press button 5 to activate/deactivate the air
conditioning system. To cool the air more quickly, you can use
interior air recirculation for a
few moments by
pressing button 4 . Then return to the intake of
exterior air.
The air conditioning does not operate
when the air flow adjustment control 2 is in
position " 0".
Switching the system off may result in
some discomfort (humidity, misting).
1. Temperature adjustment for left/right side.
2. Air flow adjustment.
3. Air distribution adjustment.
4. Recirculation of interior air.
5. Air conditioning on/off.
6. Automatic comfort programme.
7. Automatic visibility programme.
3
Ease of use and comfort