2019 MAZDA MODEL CX-30 roof

The Rear Cross Traffic Alert (RCTA)
uses rear side radar sensor to detect
vehicles approaching from the rear
left and right sides of the vehicle,
and it assists the driver in checking
the rear of the vehicle while reversing
by flashing the Blind Spot Monitoring
(BSM) warning lights and activating
the warning sound.
Refer to Rear Cross Traffic Alert
(RCTA) on page 4-126.
360°View Monitor Range
1. Cameras
2. Ultrasonic sensors
3. Front/Rear side radar sensors
WARNING
Always confirm the safety of the area
around the vehicle with the mirrors
and directly with your eyes when
driving:
The 360°View Monitor is an auxiliary
device which assists the driver in
checking the safety of the area around
the vehicle.
The shooting range of the cameras and
detection range of the sensors are
limited. For example, the areas in black
at the front and rear of the vehicle
image and the seams where each of
the camera images merge are blind
spots where an obstruction may not be
visible. In addition, the extended
vehicle width lines and projected
vehicle path lines are only to be used
as references, and the images on the
screen may differ from the actual
conditions.
CAUTION
¾Do not use the 360°View Monitor
under any of the following
conditions.
¾Icy or snow-covered roads.
¾Tyre chains or a temporary spare
tyre is installed.
¾The front or rear doors are not fully
closed.
¾The vehicle is on a road incline.
¾The door mirrors are retracted.
¾Do not hit the front/rear camera,
front bumper, liftgate, and door
mirrors forcefully. The camera
position or installation angle may
shift.
¾The cameras are waterproof. Do not
disassemble, modify, or remove a
camera.
¾The camera cover is made of hard
plastic, therefore do not apply oil
film remover, organic solvents, wax,
or coating agents. If any such agent
gets on the camera cover, wipe it off
using a soft cloth immediately.
¾Do not rub the camera lens
forcefully, or clean it with an abrasive
or hard brush. Otherwise, it could
scratch the camera lens and
negatively affect the images.
When Driving
i-ACTIVSENSE
4-186

¾The Forward Sensing Camera (FSC)
includes a function for detecting a
soiled windscreen and informing the
driver, however, depending on the
conditions, it may not detect plastic
shopping bags, ice or snow on the
windscreen. In such cases, the
system cannot accurately determine
a vehicle ahead and may not be able
to operate normally. Always drive
carefully and pay attention to the
road ahead.
NOTE
xIn the following cases, the Forward
Sensing Camera (FSC) cannot detect
target objects correctly, and each
system may be unable to operate
normally.
xThe height of the vehicle ahead is
low.
xYou drive your vehicle at the same
speed as the vehicle ahead.
xHeadlights are not turned on
during the night or when going
through a tunnel.
xIn the following cases, the Forward
Sensing Camera (FSC) may not be
able to detect target objects
correctly.
xUnder bad weather condition,
such as rain, fog and snow.
xThe window washer is being used
or the windscreen wipers are not
used when it's raining.
xIce, fog, snow, frost, rainfall, dirt,
or foreign matter such as a plastic
bag is stuck on the windscreen.
xTrucks with low loading platforms
and vehicles with an extremely low
or high profile.
xWhen driving next to walls with no
patterning (including fences and
longitudinally striped walls).
xThe tail lights of the vehicle ahead
are turned off.
xA vehicle is outside the
illumination range of the
headlights.
xThe vehicle is making a sharp turn,
or ascending or descending a steep
slope.
xEntering or exiting a tunnel.xHeavy luggage is loaded causing
the vehicle to tilt.
xStrong light is shone at the front of
the vehicle (back light or
high-beam light from on-coming
vehicles).
xThere are many light emitters on
the vehicle ahead.
xWhen the vehicle ahead is not
equipped with tail lights or the tail
lights are turned off at nighttime.
xElongated luggage or cargo is
loaded onto installed roof rails and
covers the Forward Sensing
Camera (FSC).
xExhaust gas from the vehicle in
front, sand, snow, and water
vapour rising from manholes and
grating , and water splashed into
the air.
xWhen towing a malfunctioning
vehicle.
xThe vehicle is driven with tyres
having significantly different wear.
xThe vehicle is driven on down
slopes or bumpy roads.
xThere are water puddles on the
road.
xThe surroundings are dark such as
during the night, early evening, or
early morning , or in a tunnel or
indoor parking lot.
xThe illumination brightness of the
headlights is reduced or the
headlight illumination is weakened
due to dirt or a deviated optical
axis.
When Driving
i-ACTIVSENSE
4-218

Rear View Monitor*
▼Rear View Monitor
The rear view monitor provides visual
images of the rear of the vehicle when
reversing.
WARNING
Always drive carefully confirming the
safety of the rear and the surrounding
conditions by looking directly with
your eyes:
Reversing the vehicle by only looking at
the screen is dangerous as it may cause
an accident or a collision with an
object. The rear view monitor is only a
visual assist device when reversing the
vehicle. The images on the screen may
be
different from the actual conditions.
CAUTION
¾Do not use the rear view monitor
under the following conditions:
Using the rear view monitor under
the following conditions is
dangerous and could result in injury
or vehicle damage or both.
¾Icy or snow-covered roads.
¾Tyre chains or a temporary spare
tyre is installed.
¾The vehicle is on a road incline.
¾When the display is cold, images
may course across the monitor or the
screen and may be dimmer than
usual, which could cause difficulty in
confirming the surrounding
conditions of the vehicle. Always
drive carefully confirming the safety
of the rear and the surrounding
conditions by looking directly with
your eyes.
¾Do not apply excessive force to the
camera. The camera position and
angle may deviate.
¾Do not disassemble, modify, or
remove it as it may no longer be
waterproof.
¾The camera cover is made of plastic.
Do not apply degreasing agents,
organic solvents, wax, or glass
coating agents to the camera cover.
If any are spilled on the cover, wipe
off with a soft cloth immediately.
¾Do not rub the camera cover
forcefully with an abrasive or hard
brush. The camera cover or lens may
be scratched which might affect the
images.
NOTE
xIf water, snow, or mud is stuck on
the camera lens, wipe it
off using a
soft cloth. If it cannot be wiped off,
use a mild detergent.
xIf the camera temperature changes
rapidly (Hot to cold, cold to hot), the
rear view monitor may not operate
correctly.
xWhen replacing the tyres, consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
Replacing the tyres could result in
deviation of the guide lines which
appear on the display.
xIf the vehicle's front, side, or rear has
been involved in a collision, the
alignment of the rear view parking
camera (location, installation angle)
may have deviated. Always consult
an expert repairer (we recommend
an Authorised Mazda Repairer) to
have the vehicle inspected.
When Driving
Rear View Monitor
4-238*Some models.

xClose the windows and the sunroof to reduce loud noises from outside the vehicle
and to prevent the airflow of the air-conditioning system from being a disturbance
when using Bluetooth
® Hands-Free.xMake sure that the air
flow from the air conditioner is not blowing on the
microphone.
xWhen making voice commands during a voice guidance, speak in a slightly louder
voice. But, an excessively loud voice is unnecessary.
xIf the voice recognition is poor with the guidance volume set to high, set the
Barge-In to OFF.
Some voice command examples corresponding to the voice recognition function
The specified name and number are put into the {}.
Common
xBackxHelp (You can listen to help guidance at each screen.)x{Line Number} (You can select the line number on the screen.)xNext PagexPrevious PagexCancel
Menu
xAllxNavigationxEntertainmentxCommunicationxOwner's Manual (the In-vehicle Digital Owner's Manual voice recognition can be
displayed.)
Setting
xVoice Recognition SettingsxOwner's Manual (the In-vehicle Digital Owner's Manual voice recognition can be
displayed.)
xDisplay Off
Music
xPlay Artist (You can also use “Play Artist {Artist name} {Artist name}”.)xPlay Album (You can also use “Play Album {Album Name} {Album Name}”.)xPlay Playlist (You can also use “Play Playlist {Playlist Name} {Playlist Name}”.)xPlay Song (You can also use “Play Song {Song Name} {Song Name}”.)xPlay Audiobook (You can also use “Play Audiobook {Audiobook Name}
{Audiobook Name}”.)
xPlay Podcast (You can also use “Play Podcast {Podcast Name} {Podcast Name}”.)
Radio
xTune to {Frequency} AM {Frequency} AM
Interior Features
Mazda Connect
5-25

No.FUSE RAT-
INGPROTECTED COMPONENT
F39ŠŠ
F40 40 A Air conditioner
F41ŠŠ
F42 20 A Windscreen wiper
F43 30 A
Cooling fan
*
F44 30 A Starter
F45 10 A Engine control system
F46 15 A Audio
F47 15 A For protection of various circuits
F48 7.5 A Air bag
F49 15 A Instrument cluster
F50 15 A Room light
F51 25 A Audio
F52 10 A
Sunroof
*
F53 15 A Engine control system
F54 15 A i-ACTIVSENSE
F55 50 A
For protection of various circuits
*
F56 50 AŠ
Maintenance and Care
Owner Maintenance
*Some models.6-51

¾Do not spray water in the engine
compartment. Otherwise, it could
result in engine-starting problems or
damage to electrical parts.
¾When washing and waxing the
vehicle, be careful not to apply
excessive force to any single area of
the vehicle roof. Otherwise, you
could dent the vehicle.
¾Make sure that the fuel-filler flap is
closed and lock the doors.
Otherwise, the fuel-filler flap may be
forcefully opened by water pressure
causing damage to the vehicle or
fuel-filler flap.
To help protect the
finish from rust and
deterioration, wash your Mazda
thoroughly and frequently, at least
once a month, with lukewarm or cold
water.

If the vehicle is washed improperly, the
paint surface could be scratched. Here
are some examples of how scratching
could occur.

Scratches occur on the paint surface
when:
xThe vehicle is washed without first
rinsing off dirt and other foreign
matter.
xThe vehicle is washed with a rough,
dry, or dirty cloth.
xThe vehicle is washed at a car wash
that uses brushes that are dirty or too
stiff.
xCleansers or wax containing
abrasives are used.
NOTE
xMazda is not responsible for
scratches caused by automatic car
washes or improper washing.
xScratches are more noticeable on
vehicles with darker paint finishes.
To minimize scratches on the vehicle's
paint finish:
xRinse off any dirt or other foreign
matter using lukewarm or cold water
before washing.
xUse plenty of lukewarm or cold
water and a soft cloth when washing
the vehicle. Do not use a nylon cloth.
xRub gently when washing or drying
the vehicle.
xTake your vehicle only to a car wash
that keeps its brushes well
maintained.
xDo not use abrasive cleansers or wax
that contain abrasives.
CAUTION
¾Do not use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or
anodised aluminium parts. This may
damage the protective coating; also,
cleaners and detergents may
discolour or deteriorate the paint.
Pay special attention to removing salt,
dirt, mud, and other foreign material
from the underside of the wings, and
make sure the drain holes in the lower
edges of the doors and rocker panels
are clean.

Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits
can damage the finish if not removed
immediately. When prompt washing
Maintenance and Care
Appearance Care
6-56

xExposure to direct sunlight for long
periods may cause deterioration and
shrinkage. When parking the car
under direct sunlight for long
periods, shade the interior using
sunshades.
xDo not leave vinyl products on the
leather upholstery for long periods.
They may affect the leather quality
and colouring. If the cabin
temperature becomes hot, the vinyl
may deteriorate and adhere to the
genuine leather.
▼Plastic Part Maintenance
CAUTION
Do not use polishing agents.
Depending on the product ingredients,
they could cause discolouration, stains,
cracks or peeling of the coating.
▼Instrument Panel Top (Soft pad)
Maintenance
Extremely soft material is used for the
soft pad surface. If the soft pad surface
is rubbed harshly with a dry cloth, it
could result in the surface being
damaged and leaving white scratch
marks.
1. Wipe the soiled area with a soft
cloth soaked in a mild detergent
(approx. 5%) diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
▼Active Driving Display
Maintenance*
The dust-proof sheet has a coating.
When cleaning , do not use a hard or
rough-surface cloth, or cleaning
detergent. In addition, if a chemical
solvent gets on the active driving
display, wipe it off immediately. The
dust-proof sheet could be damaged
and the surface coating could be
scratched. Use a fine, soft cloth such as
those used for cleaning eyeglasses.
NOTE
Use of compressed air when cleaning
the dust-proof sheet is recommended.
▼Panel Maintenance
If a panel becomes soiled, wipe it off
with a soft cloth soaked in clean water
and thoroughly wrung out.
If some areas require further cleaning ,
use the following procedure:
1. Wipe the soiled area with a soft
cloth soaked in a mild detergent
(approx. 5 %) diluted with water.
2. Wipe off the remaining detergent
using a cloth soaked in clean water
and wrung out well.
NOTE
Be particularly careful when cleaning
shiny surface panels and metallic parts
such as plating as they can be
scratched easily.
▼Cleaning the Window Interiors
If the windows become covered with
an oily, greasy, or waxy
film, clean
them with glass cleaner. Follow the
directions on the container.
CAUTION
¾Do not scrape or scratch the inside
of the window glass. It could
damage the thermal filaments and
the aerial lines.
¾When washing the inside of the
window glass, use a soft cloth
dampened in lukewarm water, gently
wiping the thermal filaments and the
aerial lines.
Maintenance and Care
Appearance Care
*Some models.6-61

Electromagnetic
Compatibility
▼Electromagnetic Compatibility
Your Mazda has been tested and
certified to the UN-R*1 10 regulation
as related to electromagnetic
compatibility. Radio Frequency (RF)
transmitter equipment (e.g. cellular
telephones, amateur radio
transmitters, etc.) may only be fitted to
your Mazda if they comply with the
parameters shown in the table below.
*1 UN-R stands for United Nations
Regulation.

It is your responsibility to ensure that
any equipment you have
fitted
complies with applicable local
legislations. Have any equipment
fitted
by properly trained technicians.
CAUTION
¾Do not mount any transceiver,
microphones, speakers, or any other
item in the deployment path of the
air bag system.
¾Do not fasten aerial lead to original
vehicle wiring, fuel pipes or brake
pipes. Avoid running the aerial lead
parallel with the wire harness to the
best extent possible.
¾Keep the aerial and power leads at
least 100 mm (3.9 in) from any
electronic modules and the air bags.
¾Avoid using the cigar lighter or
accessory socket as a power source
for the RF-transmitting equipment.

Aerial positions:
1. Front right of roof
2. Both sides of liftgate
3. Centre of roof
4. Front left of roof
Frequency
Band (MHz)Maximum out-
put power
(Wattage)Aerial Positions
50 Š 54 50
68 Š 87.5 50
142 Š 176 50
380 Š 470 50
806 Š 940 10
1200 Š
130010
1710 Š
188510
1885 Š
202510
2400 Š
25000.01*1In a cabin*1
*1 Only for Bluetooth®
NOTE
After the installation of RF transmitters,
check for disturbances from and to all
electrical equipment in the vehicle,
both in the standby and transmit
modes.
Check all electrical equipment:
Customer Information
Electromagnetic Compatibility
8-66