2019 MAZDA MODEL CX-30 tyre pressure

xNarrow lane roads due to road
construction or lane closures.
xThe vehicle ahead enters the radar
sensor's blind spot.
xThe vehicle ahead is running
abnormally due to accident or
vehicle damage.
xRoads with repeated up and down
slopes
xDriving on poor roads or unpaved
roads.
xThe distance between your vehicle
and the vehicle ahead is extremely
short.
xA vehicle suddenly comes close,
such as by cutting into your lane.
xTo prevent incorrect operation of the
system, use tyres of the same
specified size, manufacturer, brand,
and tread pattern on all four wheels.
In addition, do not use tyres with
significantly different wear patterns
or tyre pressures on the same vehicle
(Including the temporary spare tyre).
xIf the battery power is weak, the
system may not operate correctly.
xWhen driving on roads with little
traffic and few vehicles ahead or
obstructions for the front radar
sensor to detect, “Safety and Driver
Support Systems Temporarily
Disabled. Front Radar Obscured.
Drive Safely” may be temporarily
displayed, however, this does not
indicate a problem.
xThe radar sensors are regulated by
the relevant radio wave laws of the
country in which the vehicle is
driven. If the vehicle is driven
abroad, authorization from the
country in which the vehicle is driven
may be required.
Front Side Radar Sensor*
▼Front Side Radar Sensor
Your vehicle is equipped with front
side radar sensor. The following
systems also use the front side radar
sensor.
xFront Cross Traffic Alert (FCTA)
The front side radar sensor function by
detecting the radio waves reflected off
a vehicle approaching from the front or
an obstruction sent from the radar
sensor.
1. Front side radar sensor

The front side radar sensors are
installed inside the front bumper, one
on each side.
Always keep the surface of the front
bumper near the front side radar
sensors clean so that they operate
normally. Also, do not apply items such
as stickers.
Refer to Exterior Care on page 6-54.
CAUTION
If the front bumper receives a severe
impact, the system may no longer
operate normally. Stop the system
immediately and have the vehicle
inspected at an expert repairer (we
recommend an Authorised Mazda
Repairer).
When Driving
i-ACTIVSENSE
4-222*Some models.

Tyre Pressure Monitoring
System (TPMS)
*
▼Tyre Pressure Monitoring System
(TPMS)
The TPMS monitors the air pressure of
each tyre and if it decreases below the
specified value, the system
notifies the
driver by turning on the TPMS warning
light in the instrument cluster and
indicating a message on the
multi-information display.
For the TPMS, the air pressure data
sent from the tyre pressure sensors
installed on each wheel via radio signal
is received by the receiver unit in the
vehicle to monitor the tyre pressures.
1. Tyre pressure sensors

In addition, the current tyre pressures
can be checked using the centre
display.
Refer to the Vehicle Status Monitor
section in the Mazda Connect
Owner's Manual.
NOTE
xWhen the ambient temperature is
low, the tyre temperatures also
decrease. If the tyre temperatures
decrease, the air pressure in the tyres
will also decrease which could turn
on the TPMS warning light.
xBefore driving, visually inspect the
tyres for abnormalities. Additionally,
inspect the tyre pressures monthly. A
digital type air pressure gauge is
recommended for inspecting the tyre
pressures.
The TPMS is not a substitute for your
own periodic inspection of the tyres.
Always inspect the tyres yourself
periodically.
CAUTION
¾Each tyre, including the spare (if
provided), should be checked
monthly when cold and inflated to
the inflation pressure recommended
by the vehicle manufacturer on the
vehicle placard or tyre
inflation
pressure label. (If your vehicle has
tyres of a different size than the size
indicated on the vehicle placard or
tyre inflation pressure label, you
should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a
tyre pressure monitoring system
(TPMS) that illuminates a low tyre
pressure telltale when one or more
of your tyres is
significantly
under-inflated. Accordingly, when
the low tyre pressure telltale
illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper
pressure. Driving on a significantly
under-inflated tyre causes the tyre to
overheat and can lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and may
affect the vehicle's handling and
stopping ability.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-232*Some models.

Please note that the TPMS is not a
substitute for proper tyre
maintenance, and it is the driver's
responsibility to maintain correct tyre
pressure, even if under-inflation has
not reached the level to trigger
illumination of the TPMS low tyre
pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to
indicate when the system is not
operating properly.
The TPMS malfunction indicator is
combined with the low tyre pressure
telltale. When the system detects a
malfunction, the telltale will flash for
approximately one minute and then
remain continuously illuminated.
This sequence will continue upon
subsequent vehicle start-ups as long
as the malfunction exists. When the
malfunction indicator is illuminated,
the system may not be able to detect
or signal low tyre pressure as
intended. TPMS malfunctions may
occur for a variety of reasons,
including the installation of
replacement or alternate tyres or
wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more
tyres or wheels on your vehicle to
ensure that the replacement or
alternate tyres and wheels allow the
TPMS to continue to function
properly.
¾To avoid false readings, the system
samples for a little while before
indicating a problem. As a result it
will not instantaneously register a
rapid tyre deflation or blow out.▼If there is a problem with the Tyre
Pressure Monitoring System
(TPMS)
If the TPMS warning light flashes, there
may be a problem with the system.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) to have the system inspected.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Flashing) on page
7-57.
In the following cases, the system
cannot recognise the tyre pressures
correctly and the TPMS warning light
may flash.
xThere is equipment or a device
nearby emitting radio signals the
same as a tyre pressure sensor.
xA metallic object such as a
non-genuine electronic device is
installed near the centre of the
instrument panel (obstructs the radio
signals from the tyre pressure sensors
to the receiver).
xA device such as one of the following
is used in the cabin.
xElectronic devices such as a
computer.
xConverter devices such as a
DC-AC converter.
xThere is a large accumulation of
snow or ice around the vehicle tyres.
xThe battery in a tyre pressure sensor
is dead.
xA wheel not equipped with a tyre
pressure sensor is used.
xTyres employing steel in the sidewall
of the tyre are installed.
xTyre chains are used.
▼When a tyre pressure decreases
If the TPMS warning light turns on, a
tyre pressure may be low. Inspect the
When Driving
Tyre Pressure Monitoring System (TPMS)
4-233

tyre pressures and adjust them to the
correct inflation pressure.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Turns on) on page
7-60.
▼Tyres and Wheels
CAUTION
When inspecting/adjusting the tyre
pressures, do not apply excessive force
to the air valve of the tyre pressure
sensor. Otherwise, the tyre pressure
sensor could be damaged.
When changing tyres and wheels
When changing the tyres or wheels
(such as installing winter tyres), it will
be necessary to register the ID signal
code of the tyre pressure sensor to the
TPMS.
Have an expert repairer (we
recommend an Authorised Mazda
Repairer) do the registration or register
the ID signal codes of the tyre pressure
sensors using the following procedure.
NOTE
The tyre pressure sensors on each
wheel have a unique ID signal code.
For the TPMS to operate correctly, the
ID signal codes of the tyre pressure
sensors need to be registered to the
system.
1. Wait more than 19 minutes after
changing a tyre or wheel.
2. After more than 19 minutes have
passed, drive the vehicle at a speed
of about 25 km/h (16 mph) or
faster for 3 minutes or longer. While
driving, the ID signal codes of the
tyre pressure sensors are
automatically registered.
NOTE
If you drive the vehicle within 19
minutes of changing a tyre or wheel,
the TPMS warning light will flash
because the ID signal codes for the
tyre pressure sensors were not
registered. In this case, stop the vehicle
and register the ID signal codes of the
tyre pressure sensors following the
procedure.
When replacing tyres and wheels
CAUTION
¾When replacing the tyres and
wheels, consult an expert repairer
(we recommend an Authorised
Mazda Repairer) Otherwise, the tyre
pressure sensors could be damaged
when replacing them.
¾Do not install non-genuine wheels. If
wheels other than genuine ones are
installed, it may not be possible to
install the tyre pressure sensors.
When replacing a tyre or wheel, always
install the tyre pressure sensor. The
following combinations of tyres,
wheels, or tyres and wheels are
possible.
xThe tyre pressure sensor from the old
wheel is removed and it is installed
to the new wheel.
xOnly a tyre is replaced without
replacing the tyre pressure sensor
and wheel.
xA new tyre pressure sensor is
installed to a new wheel.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-234

NOTE
When installing a new tyre pressure
sensor, the ID signal code for the tyre
pressure sensor needs to be registered.
For details on purchasing a tyre
pressure sensor and registering the ID
signal of the tyre pressure sensor,
consult an expert repairer (we
recommend an Authorised Mazda
Repairer).
When Driving
Tyre Pressure Monitoring System (TPMS)
4-235

Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Air filter *5CCRCCRCCRCCR
Fuel filter RRRR
Fuel lines and hosesExcept Uk-
raineIIIIII
Ukraine IIIIIIIIIIII
SKYACTIV-G 2.0, SKYACTIV-X 2.0, AND SKYACTIV-D 1.8
Drive belts
*6IIII
Engine coolant level IIIIIIIIIIII
Engine coolant
*7Replace at first 200,000 km (125,000 miles) or 10 years;
after that, every 100,000 km (62,500 miles) or 5 years.
Battery
*8*9IIIIIIIIIIII
Brake lines, hoses and connections IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIII
Brake
fluid
*10RRRRRR
Disc brakes IIIIIIIIIIII
Manual transmission oil Replace every 180,000 km (112,500 miles).
Steering operation and linkagesIIIIII
Rear differential oil
*11
Transfer oil*11
Front and rear suspension, ball joints and
wheel bearing axial playIIIIII
Driveshaft dust boots IIIIII
Exhaust system and heat shields Inspect every 100,000 km (62,500 miles) or 8 years.
Bolts and nuts on chassis and body TTTTTT
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Cabin air filter (if installed) R R R R R R
Tyre inflation pressure and tyre wear
*12*13IIIIIIIIIIII
Emergency
flat tyre repair kit (if installed)
*14IIIIIIIIIIII
Self-test with Mazda Modu-
lar Diagnostic System
(M-MDS)
*15*16
SKYACTIV-G & SKYACTIV-XUkraine IIIIIIIIIIII
Maintenance and Care
Scheduled Maintenance
6-4

Maintenance Item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Battery *3*4IIIIIIIIIIII
Vacuum brake booster and
hoseWith vacuum
boosterIIIIIIIIIIII
Brake and clutch fluid level IIIIIIIIIIII
Brake lines, hoses and connections I I I I I I I I I I I I
Disc brakes IIIIIIIIIIII
Bolts and nuts on chassis and body T T T T T T T T T T T T
Front and rear suspension, ball joints and
wheel bearing axial playIIIIIIIIIIII
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Ty re
inflation pressure and tyre wear
*5*6IIIIIIIIIIII
Emergency
flat tyre repair kit (if installed)
*7IIIIIIIIIIII
Fuel lines and hoses IIIIII
Steering operation and linkages IIIIII
Brake
fluid
*8RRRRRR
Cabin air filter (if installed) RRRRRR
Hoses and tubes for emission I I I
Driveshaft dust boots I I I I
Air filter
*9RRR
Exhaust system and heat shields I I
Manual transmission oil Replace every 100,000 km or 5 years.
Spark plugSKYACTIV-G
2.0/
SKYACTIV-G
2.5Replace every 120,000 km.
SKYACTIV-X
2.0Replace every 64,000 km.
Fuel filter Replace every 135,000 km.
Engine coolant
*10Replace at first 195,000 km or 10 years; after that, every
90,000 km or 5 years.
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fill up, or replace if necessary.
T: Tighten
R: Replace
Maintenance and Care
Scheduled Maintenance
6-7

Maintenance item 1st2nd3rd 4th 5th 6th 7th 8th 9th10th 11th 12th
Exhaust system and heat shields IIIIIIIIIIII
Function of all lights I I I I I I I I I I I I
Body condition (for rust, corrosion and per-
foration)IIIIIIIIIIII
Tyre inflation pressure and tyre wear
*5*6IIIIIIIIIIII
Emergency flat tyre repair kit (if installed)
*7IIIIIIIIIIII
Fuel lines & hoses IIIIII
Brake
fluid
*8RRRRRR
Cabin air filter (if installed) R R R R R R
Hoses and tubes for emission I I I
Air
filter
*9RRRR
Manual transmission oil R R
Fuel filterExcept below
countriesReplace every 120,000 km.
Azerbaijan/
ArmeniaReplace every 60,000 km.
Engine coolant
*10Replace at first 195,000 km or 120 months; after that,
every 90,000 km or 60 months.
Rear differential oil
*11
Transfer oil*11
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust,
fill up, or replace if necessary.
T: Tighten
R: Replace
Remarks:
*1 Reset the engine oil data whenever replacing the engine oil regardless of the message/wrench
indicator light display.
*2 Also inspect the air conditioner drive belts, if installed.
If the vehicle is driven primarily under any of the following conditions, inspect the drive belts at every
7,500 km or 6 months.
a) Driving for long period in extremely wet or heavy rain condition.
*3 Inspect the battery electrolyte level, specific gravity and outer appearance. The sealed battery only
requires an outer appearance inspection.
*4 Inspection is only subjected for lead-acid battery.*5 Tyre rotation is recommended every 15,000 km.*6 Inspect a spare tyre if installed.
Maintenance and Care
Scheduled Maintenance
6-10