2019 MAZDA MODEL CX-30 air condition

All doors, fuel-filler flap, and liftgate
will automatically unlock if they are
locked using the power door locks
with any door or the liftgate open.
The vehicle lock-out prevention
feature does not operate while the
ignition is switched off.
When all doors, fuel-filler flap, and
liftgate are locked using the power
door lock with any door or the
liftgate open, the closed doors,
fuel-filler flap, and liftgate are
locked. After that, when all doors
and the liftgate are closed, all doors
and the liftgate are locked. However,
if the key is inside the vehicle, all
doors, fuel-filler flap, and liftgate are
automatically unlocked.
(With the advanced keyless
function)
The beep sound is heard for about
10 seconds to notify the driver that
the key has been left in the vehicle.
(Without the advanced keyless
function)
The horn sound is heard twice to
notify the driver that the key has
been left in the vehicle.
x(Door unlock (control) system with
collision detection)
This system automatically unlocks the
doors, fuel-filler flap, and liftgate in
the event the vehicle is involved in an
accident to allow passengers to get
out of the vehicle immediately and
prevent being trapped inside. While
the ignition is switched ON and in
the event the vehicle receives an
impact strong enough to inflate the
air bags, all the doors,
fuel-filler
flap,
and liftgate are automatically
unlocked after about 6 seconds have
elapsed from the time of the
accident.
The doors, fuel-filler flap, and liftgate
may not unlock depending on how
an impact is applied, the force of the
impact, and other conditions of the
accident.
If door-related systems or the battery
is malfunctioning , the doors and
the , fuel-filler flap, and liftgate may
not unlock depending on your
vehicle type.
▼Unlocking with Auxiliary Key
Only the driver's door can be unlocked
using the auxiliary key.
Refer to Keys on page 3-2.
Insert the auxiliary key while the
driver's door handle is pulled and turn
the key to the unlock side. Turn the
auxiliary key back to its original
position before removing it.
NOTE
If you attempt to open the driver’s
door using an unauthorised auxiliary
key, the key cylinder will spin around
but the door will not unlock.
▼Double Locking System*
The double locking system is designed
to prevent someone who has broken
into your vehicle from opening the
door from the inside.

If you have any problems with the
double locking system, consult an
expert repairer (we recommend an
Authorised Mazda Repairer).
Before Driving
Doors and Locks
3-12*Some models.

SCHEDULED MAINTENANCE for the
details.
Refer to Scheduled Maintenance
(Europe) on page 6-3.
Refer to Scheduled Maintenance
(Except Europe) on page 6-6.
CAUTION
¾According to the inspection result of
scheduled maintenance, Mazda
genuine deposit cleaner is to be
used. Neglected deposits in the fuel
system may cause malfunction
indicator light coming on to indicate
an engine malfunction, and if the
vehicle continues to be driven under
this condition, it could result in
problems occurring such as idling
failure and poor acceleration.
¾The Mazda genuine deposit cleaner
is not a guarantee of engine
performance no matter the quality of
the fuel used. When a problem
occurs even though the
specified fuel
is used and the Mazda genuine
deposit cleaner is used according to
the instructions, consult an
Authorised Mazda Dealer.
¾If a deposit cleaner other than the
Mazda genuine product is used, it
could result in damage to the fuel
system or the engine internally;
therefore use only the Mazda
genuine product. Mazda genuine
deposit cleaner: K002 W0 001
¾If cleaning required according to the
inspection result of scheduled
maintenance is not done with the
Mazda genuine deposit cleaner,
repair cost for engine malfunctions
caused by deposits are borne by the
customer.
How to use the cleaner
With the fuel tank full, infuse 1 bottle
of Mazda genuine deposit cleaner
directly into the fuel tank.
NOTE
xInfusing the deposit cleaner when
the fuel tank is full provides the
concentration of cleaner within the
range
effective for removing the
deposits and the best cleaning
results can be obtained by the full
tank of fuel with the infused deposit
cleaner contacting the deposits for a
long period of time until the full tank
of fuel is nearly used up.
▼Fuel Requirements
(SKYACTIV-D
1.8)
The vehicle will operate efficiently on
diesel fuel with specification EN590 or
the equivalent.
CAUTION
¾Never use fuel other than
specification EN590 or the
equivalent for your vehicle. Use of
petrol or paraffin in diesel engines
will result in engine damage.
¾Never add fuel system additives.
Otherwise, the emission control
system could be damaged. Consult
an expert repairer (we recommend
an Authorised Mazda Repairer) for
details.
NOTE
When refuelling , always add at least 10
L (2.6 US gal, 2.2 Imp gal) of fuel.
Before Driving
Fuel and Emission
3-31

Theft-Deterrent System*
▼Theft-Deterrent System
If the theft-deterrent system detects an
inappropriate entry into the vehicle or
the intrusion sensor detects movement
in the vehicle which could result in the
vehicle (with the intrusion sensor) or
its contents being stolen, the alarm
alerts the surrounding area of an
abnormality by sounding the siren/
horn and flashing the hazard warning
lights.

The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Intrusion sensor
*
The intrusion sensor uses ultrasonic
waves to detect movement inside the
vehicle and to raise an alert of an
intrusion into the vehicle.

The intrusion sensor detects certain
kinds of movement inside the vehicle,
however, it may also respond to
phenomenon outside the vehicle such
as vibrations, loud noise, wind, and air
currents.
CAUTION
In order for the intrusion sensor to
operate appropriately, be aware of the
following:
¾Do not hang clothing or objects from
a head restraint or a coat hook.
¾Return the extension sunvisors to
their original positions.
¾Do not blind the intrusion sensor by
covering it or placing objects over it.
¾Do not allow the intrusion sensor to
get soiled or wipe it with a liquid.
¾Do not shock or cause an impact to
the intrusion sensor or the intrusion
sensor bezel.
¾Do not install seats that are not
Mazda genuine products.
¾To prevent obstruction of intrusion
sensor, do not place objects or cargo
near the intrusion sensor that are
higher than the head restraints.

1. Intrusion sensor and intrusion
sensor bezel
▼Operation
Siren/Horn triggering conditions
The siren/horn sounds intermittently
and the hazard warning lights flash for
about 30 seconds when the system is
triggered by any one of the following:
With the intrusion sensor
xUnlocking a door with the auxiliary
key, door lock switch, or an inside
door-lock knob.
xForcing open a door, the bonnet or
the liftgate.
xOpening the bonnet by operating
the bonnet release handle.
xSwitching the ignition ON without
using the push button start.
xThe intrusion sensor detects a
movement in the vehicle.
Before Driving
Security System
*Some models.3-49

NOTE
xThe theft-deterrent system can
also be armed by activating the
auto relock function with all the
doors, the liftgate and the bonnet
closed.
Refer to Transmitter on page 3-5.
xThe system will disarm if one of
the following operations takes
place within 20 seconds after
pressing the lock button:
xUnlocking any door.xOpening any door.xOpening the bonnet.xSwitching the ignition ON.
To rearm the system, do the
arming procedure again.
xWhen the doors are locked by
pressing the lock button on the
transmitter while the
theft-deterrent system is armed,
the hazard warning lights will
flash once to indicate that the
system is armed.
▼Cancelling the Intrusion Sensor
(With the Intrusion Sensor)
If the theft deterrent system has been
armed while any of the following
conditions are present, cancel the
intrusion sensor to prevent the alarm
from triggering unnecessarily.
xLeaving the vehicle with a movable
object, passengers or pets remaining
inside.
xLeaving an object inside the vehicle
that can roll around, such as when
the vehicle is placed on a tilting,
unstable surface when being
shipped.
xHanging small objects/accessories in
the vehicle, hanging clothing on a
coat hook, or placing other items
which can move easily inside the
vehicle.
xParking in an area where there is
strong vibration or loud noise.
xWhen using a high pressure or
automatic car wash.
xContinuous shock and vibration from
hail or thunder and lightning is
transmitted to the vehicle.
xDoors are locked with a window or
the sunroof* left open.xAn accessory heater or device that
produces moving air and vibration
operates while the theft deterrent
system is armed.
NOTE
If any door or the liftgate remains
closed for 30 seconds, all the doors
and the liftgate automatically re-lock
and the theft deterrent system arms
even if a window and the sunroof
* is
left open.

To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will flash 3
times.
NOTE
xTo reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
xThe intrusion sensor is operational
when the theft-deterrent system is
armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the
theft-deterrent system is armed.
▼To Turn Off an Armed System
An armed system can be turned off
using any one of the following
methods:
Before Driving
Security System
*Some models.3-51

Running-In
▼Running-In
No special running-in is necessary, but
a few precautions in the
first 1,000 km
(600 miles) may add to the
performance, economy, and life of the
vehicle.
xDo not race the engine.xDo not maintain one constant
speed, either slow or fast, for a long
period of time.
xDo not drive constantly at
full-throttle or high engine rpm for
extended periods of time.
xAvoid unnecessary hard stops.xAvoid full-throttle starts.xDo not tow a trailer.
Saving Fuel and
Protection of the
Environment
▼Saving Fuel and Protection of the
Environment
How you operate your Mazda
determines how far it will travel on a
tank of fuel. Use these suggestions to
help save fuel and reduce CO
2.
xAvoid long warm-ups. Once the
engine runs smoothly, begin driving.
xAvoid fast starts.xDrive at lower speeds.xAnticipate when to apply the brakes
(avoid sudden braking).
xFollow the maintenance schedule
and have an expert repairer (we
recommend an Authorised Mazda
Repairer) perform inspections and
servicing.
Refer to Europe on page 6-3.
Refer to Except Europe on page
6-6.
xUse the air conditioner only when
necessary.
xSlow down on rough roads.xKeep the tyres properly inflated.xDo not carry unnecessary weight.xDo not rest your foot on the brake
pedal while driving.
xKeep the wheels in correct
alignment.
xKeep windows closed at high
speeds.
xSlow down when driving in
crosswinds and headwinds.
Before Driving
Driving Tips
3-53

This is for improved exhaust gas
purification and does not indicate
any parts defect.
1. Make sure you are carrying the key.
2. Occupants should fasten their seat
belts.
3. Make sure the parking brake is on.
4. Continue to depress the brake
pedal firmly until the engine has
completely started.
5.(Manual transmission)
Continue to depress the clutch
pedal firmly until the engine has
completely started.
(Automatic transmission)
Put the vehicle in park (P). If you
must restart the engine while the
vehicle is moving, shift into neutral
(N).
NOTE
x(Manual transmission)
The starter will not operate if the
clutch pedal is not depressed
sufficiently.
x(Automatic transmission)
The starter will not operate if the
selector lever is not in P or N
position and the brake pedal is
not depressed sufficiently.
6. Make sure that the push button
start indicator light (green) turns
on.
1. Indicator light
2. Push button start
NOTE
xIf the push button start indicator
light (green) flashes, make sure
that the key is being carried.
xIf the push button start indicator
light (green)
flashes with the key
being carried, touch the key to
the push button start and start
the engine.
Refer to Engine Start Function
When Key Battery is Dead on
page 4-8.
CAUTION
If the KEY warning indication (red)
is displayed, or the push button
start indicator light (amber)
flashes,
this could indicate a problem with
the engine starting system. This may
prevent the engine from starting or
from switching the ignition to ACC
or ON.
Refer to KEY Warning Indication/
Warning Light (Red) on page
7-56.
Have your vehicle inspected at an
expert repairer (we recommend an
Authorised Mazda Repairer) as
soon as possible.
NOTE
xUnder the following conditions,
the KEY warning indication (red)
is displayed after the push button
start is pressed. This informs the
driver that the push button start
will not switch to ACC, even if it
is pressed from off (page 7-56).
xThe key battery is dead.xThe key is out of operational
range.
xThe key is placed in areas where
it is difficult for the system to
detect the signal (page 3-7).
When Driving
Start/Stop Engine
4-6

NOTE
x(Germany)
Drive immediately after starting
the engine. However do not use
high engine speeds until reaching
the operating temperature.
x(SKYACTIV-G 2.0, SKYACTIV-G
2.5,
SKYACTIV-X 2.0)
xWhether the engine is cold or
warm, it should be started
without the use of the
accelerator.
xIf the engine does not start the
first time, refer to Starting a
Flooded Engine under
Emergency Starting. If the
engine still does not start, have
your vehicle inspected by an
expert repairer (we recommend
an Authorised Mazda Repairer)
(page 7-42).
x(SKYACTIV-D 1.8)
If the ambient temperature is
lower than about >+ 10 °C (14
°F), the maximum engine speed
may not be attained for about 3
minutes after the engine starts to
protect the engine.
x(Manual transmission vehicle
with i-stop function)
If the engine has stopped due to
stalling , it can be restarted by
depressing the clutch pedal
within 3 seconds of the engine
stopping.
The engine cannot be restarted
even if the clutch pedal is
depressed under the following
conditions:
xThe driver's door is open.xThe driver's seat belt is
unfastened.
xThe clutch pedal is not released
completely after the engine
stalled.
xThe clutch pedal is depressed
with the engine not stopped
completely.
▼Engine Start Function When Key
Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not to
allow the following , otherwise the
signal from the key will not be received
correctly and the engine may not start.
¾Metal parts of other keys or metal
objects touch the key.
¾Spare keys or keys for other vehicles
equipped with an immobilizer
system touch or come near the key.
¾Devices for electronic purchases, or
security passage touch or come near
the key.
If the engine cannot be started due to
a dead key battery, the engine can be
started using the following procedure:
1. Continue to depress the brake
pedal firmly until the engine has
completely started.
2.(Manual transmission)
Continue to depress the clutch
pedal
firmly until the engine has
completely started.
When Driving
Start/Stop Engine
4-8

2. When the accelerator pedal is
depressed or the RES switch is
operated while the vehicle is kept
stopped by the MRCC with Stop &
Go function/CTS, the engine
automatically restarts. The engine
restarts automatically when the
accelerator pedal is depressed with
the selector lever in the D/M
position (not in second gear fixed
mode).
(When the vehicle is stopped by the
AUTOHOLD function)
1. When the brake pedal is depressed
while the vehicle is being driven
(except for driving in the R or M
position second gear fixed mode)
and the vehicle is brought to a stop,
the i-stop function will operate and
it continues to operate even if the
brake is released.
2. The engine restarts automatically
when the accelerator pedal is
depressed with the selector lever in
the D/M position (not in second
gear fixed mode).
3. If the selector lever is in the N or P
position, the engine does not
restart when the brake pedal is
released. The engine restarts when
the brake pedal is depressed again
or the selector lever is shifted to the
D, M (not in second gear fixed
mode) or the R position. (For the
purposes of safety, always keep the
brake pedal depressed when
shifting the selector lever while
engine idling is stopped.)
Engine idle stopping and restarting
while driving (With M Hybrid)
(When not using MRCC with Stop &
Go function/CTS)
1. Engine idling stops when the
vehicle speed is about 20 km/h (12
mph) or slower after depressing the
brake pedal while driving the
vehicle (in D position).
2. The engine restarts automatically
after releasing the brake pedal with
the selector lever in the D position.
(When using MRCC with Stop & Go
function/CTS)
1. Engine idling stops when the
vehicle speed is about 20 km/h (12
mph) or slower after decelerating
the vehicle a certain amount or
more while in headway control
using the MRCC with Stop & Go
function/CTS.
2. If it is necessary to accelerate while
in headway control using the MRCC
with Stop & Go function/CTS, the
engine restarts automatically.
Operation conditions
Under the following conditions, engine
idling stops and the i-stop indicator
light (green) turns on.
x(SKYACTIV-G 2.0,
SKYACTIV-G 2.5,
SKYACTIV-X 2.0)
The engine is warmed up.
x(SKYACTIV-D 1.8)
The engine is not cold.
xThe engine has been started and the
vehicle is driven for a certain period.
xThe engine is started with the bonnet
closed.
xAll doors, liftgate, and bonnet are
closed.
xThe driver's seat belt is fastened.xThe air conditioner is not operating
with the airflow mode in the
position.xThe temperature setting dial of the
air conditioner is in a position other
than maximum heating or maximum
cooling (A/C ON) position.
x(Automatic air-conditioning)
The vehicle's interior temperature
and the set temperature for the air
conditioner are nearly the same.
When Driving
Start/Stop Engine
4-13