2019 MAZDA MODEL CX-30 display

(warning/risk avoidance support
system) (white) and the i-ACTIVSENSE
warning indication/warning light on
the multi-information display turns on
and a message is indicated.
Refer to i-ACTIVSENSE Status Symbol
(Warning/Risk Avoidance Support
System) on page 4-96.
▼Steering Wheel Operation Assist
When the system determines that the
vehicle might be deviating from its
lane, the steering wheel operation
assist operates.
The system notifies the driver that it
provided steering wheel operation
assistance on the multi-information
display and the active driving display.
Multi-information display (Basic
display)
Multi-information display
(i-ACTIVSENSE display)
Active driving display
NOTE
When the driver operates the steering
wheel while the steering wheel
operation assist is operating , the
steering wheel operation assistance is
cancelled.
▼System Cancelling
The LAS can be set to inoperable.
x(If only the LAS is turned
off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the LAS is turned off by operating
the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
When Driving
i-ACTIVSENSE
4-165

Adjustable Speed Limiter
(ASL)
*
▼Adjustable Speed Limiter (ASL)
The ASL is a function to prevent the
vehicle from being driven at a vehicle
speed faster than a set speed. The
vehicle speed is controlled to kept it
below the set speed even if the
accelerator pedal is depressed.
The ASL can be set between 30 km/h
(19 mph) and 200 km/h (125 mph).
The vehicle speed may exceed the set
speed when the vehicle is driven on a
down slope, however, the system
notifies the driver by flashing the
display and operating a warning
sound.
WARNING
Always turn off the system when
changing drivers:
If the driver is changed and the new
driver is unaware of the ASL function,
the vehicle may not accelerate when
the driver depresses the accelerator
pedal, leading to an accident.
The system consists of the ASL display
and the speed limiter switch on the
steering wheel.
Multi-information display (Basic
display)
1. ASL set vehicle speed

Multi-information display
(i-ACTIVSENSE display)
1. ASL set vehicle speed

Active driving display
1. ASL set vehicle speed

When Driving
i-ACTIVSENSE
4-166*Some models.

Speed limiter switch
1. CANCEL switch
2. RES switch
3. LIM switch
▼Adjustable Speed Limiter (ASL)
Standby Indication (White)/
Adjustable Speed Limiter (ASL) Set
Indication (Green)
ASL standby indication (white)
The indication is display in white when
the LIM switch is pressed and the ASL
is activated.
ASL set indication (green)
The indication is display in green when
a speed has been set.
When Driving
i-ACTIVSENSE
4-167

▼Adjustable Speed Limiter (ASL) Display
The setting status of the ASL is displayed in the active driving display or the display in
the instrument cluster.
StatusIndication on
multi-informa-
tion display/
active driving
displayExplanation
Stand-by dis-
play
Displays when the speed limiter switch is operated and the system
is turned on.
Turns off when the system is turned off.
Setting display
Displays when the SET- or SET+ switch is operated and the speed is
set.
Cancel display
Displays when any of the following operations is done and the sys-
tem is temporarily cancelled.
xCANCEL switch is operatedxAccelerator pedal is strongly depressed
Warning display
If the vehicle speed exceeds the set speed by about 5 km/h (3
mph) or more, the ASL display
flashes.
The display flashes until the vehicle speed decreases to the set
speed or less.
A warning beep is activated at the same time as the warning dis-
play.
Refer to Speed Limiter Warning Beep on page 7-72.
▼Activation/Deactivation
NOTE
When the ignition is switched
off, the
system status before it was turned
off is
maintained.
For example, if the ignition is switched
off while the ASL is operating , the
system will be operable when the
ignition is switched ON the next time.
Activation
Press the LIM switch to activation the
system. The ASL screen is displayed,
and the ASL standby indication
displays in white.
Deactivation
Press the LIM switch again to
deactivation the system. The ASL
screen is no longer displayed and the
ASL indication does not display.
When Driving
i-ACTIVSENSE
4-168

▼Setting the System
WARNING
Always verify the safety of the
surrounding area when setting the
ASL:
If the speed is set lower than the
current vehicle speed, the vehicle
speed is decreased to the set speed.
Verify the safety of the surrounding
area and keep a safer distance
between vehicles ahead and behind
you.
1. Press the LIM switch to turn the
system on.
2. Press the RES switch up (SET+) or
down (SET-) to set the speed.
When the current vehicle speed is
30 km/h (19 mph) or more, the
speed is set to the current vehicle
speed. When the current vehicle
speed is less than 30 km/h (19
mph), the speed is set to 30 km/h
(19 mph).
3. To increase the set speed, press the
RES switch up (SET+) continuously.
The set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES switch up (SET
+) momentary. For example, the set
speed increases about 4 km/h (4
mph) by pressing the RES switch up
(SET+) 4 times.
4. To decrease the set speed, press the
RES down
(SET-) continuously. The
set speed can be adjusted in 10
km/h (5 mph) increments. The set
speed can also be adjusted in
about 1 km/h (1 mph) increments
by pressing the RES down
(SET-)
momentary. For example, the set
speed decreases about 4 km/h (4
mph) by pressing the RES down
(SET-) 4 times.
NOTE
xWhen the vehicle set speed is
displayed in the instrument cluster,
press the RES switch to set the
displayed vehicle speed.
xThe system is temporarily cancelled
when the vehicle is accelerated by
depressing the accelerator pedal
strongly, however, it resumes when
the vehicle speed decreases to the
set speed or less.
xThe vehicle speed may exceed the
set speed on a down slope.
xIn the following cases, the system
cannot be set.
xAny door is open.xThe driver's seat belt is unfastened.
▼Temporarily Cancelling the System
The system is temporarily cancelled
(stand-by status) when any of the
following operations is done while the
ASL is displayed.
xCANCEL switch is pressedxAccelerator pedal is strongly
depressed
xAny door is openedxThe driver’s seat belt is unfastened
Press the RES switch to resume the
operation at the previous set speed.
The ASL display remains displayed.
NOTE
xThe set speed can be set by pressing
the RES switch up (SET+) or down
(SET-) while the system is in stand-by
status.
xThe ASL is not cancelled by
depressing the brake pedal.
When Driving
i-ACTIVSENSE
4-169

Intelligent Speed
Assistance (ISA)
*
▼Intelligent Speed Assistance (ISA)
The ISA is a function which keeps the
vehicle speed below the speed limit
set from a speed limit sign or an
optionally set speed limit. The speed
limit can be set between 30 and 200
km/h (19-125 mph), and if the vehicle
speed exceeds the set speed limit
while driving on steep slopes, the
system notifies the driver using the
display and a warning sound.
The ISA recognises a speed limit sign
based on the
Tra ffi c Sign Recognition
System (TSR) or the navigation system
information.
Refer to
Tra ffi c Sign Recognition
System (TSR) on page 4-111.
WARNING
Always turn
off the system when
changing drivers:
If the driver is changed and the new
driver is unaware of the ISA function,
the vehicle may not accelerate when
the driver depresses the accelerator
pedal, leading to an accident.
Depending on the weather conditions
or problems with traffic signs, a traffic
sign may not be recognised or a traffic
sign
different from the actual
traffic
sign may be displayed. Always make it
your responsibility as a driver to check
the actual traffic signs. Otherwise, it
could result in an accident.
NOTE
The ISA operates only when the
navigation system's SD card (Mazda
genuine) is inserted. In addition, the
Adjustable Speed Limiter (ASL)
operates only when the navigation
system's SD card (Mazda genuine) is
not inserted. Refer to Adjustable
Speed Limiter (ASL) on page 4-166.
The system consists of the ISA display
and the speed limiter switch on the
steering wheel.

Multi-information display (Basic
display)
1. set vehicle speed

When Driving
i-ACTIVSENSE
4-170*Some models.

Multi-information display
(i-ACTIVSENSE display)
1. set vehicle speed

Active driving display
1. set vehicle speed

Speed limiter switch
1. CANCEL switch
2. RES switch
3. LIM switch
▼Intelligent Speed Assistance (ISA)
Standby Indication (White)/
Intelligent Speed Assistance (ISA)
Set Indication (Green)
ISA standby indication (white)
The indication is displayed in white
when the LIM switch is pressed and
the ISA is activated.
ISA set indication (green)
The indication is displayed in green
when a speed has been set.
When Driving
i-ACTIVSENSE
4-171

▼Intelligent Speed Assistance (ISA) Display
The setting status of the ISA is displayed in the active driving display or the display in
the instrument cluster.
StatusIndication on
multi-informa-
tion display/
active driving
displayExplanation
Stand-by dis-
play
Displays when the speed limiter switch is operated and the system
is turned on.
Turns off when the system is turned off.
Setting display
Displays when the RES switch up (SET+) or down (SET-) is operated
(while the ISA set indication is displayed), and the speed is set.
Cancel display
Displays when any of the following operations is done and the sys-
tem is temporarily cancelled.
xCANCEL switch is operatedxAccelerator pedal is strongly depressedxAny door is openedxThe driver’s seat belt is unfastened
Warning display
If the vehicle speed exceeds the set speed by about 5 km/h (3
mph) or more, the ISA display
flashes.
The display flashes until the vehicle speed decreases to the set
speed or less.
A warning beep is activated at the same time as the warning dis-
play.
Refer to Speed Limiter Warning Beep on page 7-72.
▼Activation/Deactivation
NOTE
When the ignition is switched
off, the
system status before it was turned
off is
maintained.
For example, if the ignition is switched
off while the ISA is operating, the
system will be operable when the
ignition is switched ON the next time.
Activation
Press the LIM switch to activation the
system. The ISA screen is displayed,
and the ISA standby indication displays
in white.
Deactivation
Press the LIM switch again to
deactivation the system. The ISA screen
is no longer displayed and the ISA
indication does not display.
When Driving
i-ACTIVSENSE
4-172