2019 MAZDA MODEL 2 oil
[x] Cancel search: oilPage 37 of 759
Positioning the Shoulder Portion of the Seat Belt:
Improper positioning of the shoulder portion of the seat belt is dangerous. Always make sure
the shoulder portion of the seat belt is positioned across your shoulder and near your neck,
but never under your arm, on your neck, or on your upper arm.
Positioning the Lap Portion of the Seat Belt:
The lap portion of the seat belt worn too high is dangerous. In a collision, this would
concentrate the impact force directly on the abdominal area, causing serious injury. Wear the
lap portion of the belt snugly and as low as possible.
Instructions for Use of Seat Belt Assemblies:
Seatbelts are designed to bear upon the bony structure of the body, and should be worn low
across the front of the pelvis or the pelvis, chest and shoulders, as applicable; wearing the lap
section of the belt across the abdominal area must be avoided.
Seatbelts should be adjusted as firmly as possible, consistent with comfort, to provide the
protection for which they have been designed. A slack belt will greatly reduce the protection
afforded to the wearer.
Care should be taken to avoid contamination of the webbing with polishes, oils and
chemicals, and particularly battery acid. Cleaning may safely be carried out using mild soap
and water. The belt should be replaced if webbing becomes frayed, contaminated or
damaged.
It is essential to replace the entire assembly after it has been worn in a severe impact even if
damage to the assembly is not obvious.
Belts should not be worn with straps twisted.
Each belt assembly must only be used by one occupant; it is dangerous to put a belt around a
child being carried on the occupant's lap.
No modifications or additions should be made by the user which will either prevent the seat
belt adjusting devices from operating to remove slack, or prevent the seat belt assembly from
being adjusted to remove slack.
& $ 8 7 , 2 1
Belt retraction may become difficult if the belts and rings are soiled, so try to keep them clean.
For more details about cleaning the seat belts, refer to "Seat Belt Maintenance" (page 6-68).
Ring
( V V H Q W L D O 6 D I H W \ ( T X L S P H Q W
6 H D W % H O W 6 \ V W H P V
Page 121 of 759
xBecause the electronic codes are reset
when the immobilizer system is repaired,
the keys are needed. Make sure to bring
all the keys to an expert repairer (we
recommend an Authorised Mazda
Repairer), so that they can be
programmed. 7 K H I W ' H W H U U H Q W 6 \ V W H P
, I W K H W K H I W G H W H U U H Q W V \ V W H P G H W H F W V D Q
L Q D S S U R S U L D W H H Q W U \ L Q W R W K H Y H K L F O H R U W K H
L Q W U X V L R Q V H Q V R U G H W H F W V P R Y H P H Q W L Q W K H
Y H K L F O H Z K L F K F R X O G U H V X O W L Q W K H Y H K L F O H
Z L W K W K H L Q W U X V L R Q V H Q V R U R U L W V F R Q W H Q W V
E H L Q J V W R O H Q W K H D O D U P D O H U W V W K H
V X U U R X Q G L Q J D U H D R I D Q D E Q R U P D O L W \ E \
V R X Q G L Q J W K H V L U H Q K R U Q D Q G I O D V K L Q J W K H
K D ] D U G Z D U Q L Q J O L J K W V
7 K H V \ V W H P Z L O O Q R W I X Q F W L R Q X Q O H V V L W
V
S U R S H U O \ D U P H G 6 R Z K H Q \ R X O H D Y H W K H
Y H K L F O H I R O O R Z W K H D U P L Q J S U R F H G X U H
F R U U H F W O \
, Q W U X V L R Q V H Q V R U
7 K H L Q W U X V L R Q V H Q V R U X V H V X O W U D V R Q L F Z D Y H V
W R G H W H F W P R Y H P H Q W L Q V L G H W K H Y H K L F O H D Q G
W R U D L V H D Q D O H U W R I D Q L Q W U X V L R Q L Q W R W K H
Y H K L F O H
7 K H L Q W U X V L R Q V H Q V R U G H W H F W V F H U W D L Q N L Q G V
R I P R Y H P H Q W L Q V L G H W K H Y H K L F O H K R Z H Y H U
L W P D \ D O V R U H V S R Q G W R S K H Q R P H Q R Q
R X W V L G H W K H Y H K L F O H V X F K D V Y L E U D W L R Q V O R X G
Q R L V H Z L Q G D Q G D L U F X U U H Q W V
& $ 8 7 , 2 1
In order for the intrusion sensor to operate
appropriately, be aware of the following:
¾Do not hang clothing or objects from a
head restraint or a coat hook.
¾Return the extension sunvisors to their
original positions.
¾Do not blind the intrusion sensor by
covering it or placing objects over it.
¾Do not allow the intrusion sensor to get
soiled or wipe it with a liquid.
% H I R U H ' U L Y L Q J
6 H F X U L W \ 6 \ V W H P
6 R P H P R G H O V
Page 185 of 759
▼ : U H Q F K , Q G L F D W R U / L J K W
: K H Q W K H L J Q L W L R Q L V V Z L W F K H G 2 1 W K H
Z U H Q F K L Q G L F D W R U O L J K W W X U Q V R Q D Q G W K H Q
W X U Q V R I I D I W H U D I H Z V H F R Q G V
7 K H Z U H Q F K L Q G L F D W R U O L J K W W X U Q V R Q Z K H Q
W K H S U H V H W P D L Q W H Q D Q F H S H U L R G D U U L Y H V
9 H U L I \ W K H F R Q W H Q W D Q G S H U I R U P
P D L Q W H Q D Q F H
5 H I H U W R 0 D L Q W H Q D Q F H 0 R Q L W R U R Q S D J H
6 . < $ & 7 , 9 '
7 K H Z U H Q F K L Q G L F D W R U O L J K W W X U Q V R Q X Q G H U
W K H I R O O R Z L Q J F R Q G L W L R Q V
x 7 K H H Q J L Q H R L O L V G H W H U L R U D W H G R U H [ F H H G V
W K H V S H F L I L H G D P R X Q W
x 7 K H H Q J L Q H R L O O H Y H O L V D U R X Q G W K H 0 , 1
P D U N R Q W K H G L S V W L F N R U L W L V O H V V W K D Q W K H
0 , 1 P D U N
x 7 K H H Q J L Q H R L O O H Y H O L V D U R X Q G W K H ;
P D U N R Q W K H G L S V W L F N R U L W H [ F H H G V W K H ;
P D U N
& K H F N W K H H Q J L Q H R L O 5 H I H U W R , Q V S H F W L Q J
( Q J L Q H 2 L O / H Y H O R Q S D J H
5 H S O D F H W K H H Q J L Q H R L O L I W K H Z U H Q F K
L Q G L F D W R U O L J K W G R H V Q R W W X U Q R I I H Y H Q
W K R X J K W K H H Q J L Q H R L O O H Y H O L V L Q W K H Q R U P D O
U D Q J H
NOTE
xDepending on the vehicle use
conditions, the wrench indicator light
may turn on for reasons other than the
preset maintenance period.
xWhenever the engine oil is replaced, a
reset of the vehicle engine control unit is
necessary.
Your Authorised Mazda Repairer will be
able to reset the engine control unit or
see page 6-27 for the Vehicle engine
control unit reset procedure.
▼ / R Z ( Q J L Q H & R R O D Q W 7 H P S H U D W X U H
, Q G L F D W R U / L J K W % O X H
7 K H O L J K W L O O X P L Q D W H V F R Q W L Q X R X V O \ Z K H Q
W K H H Q J L Q H F R R O D Q W W H P S H U D W X U H L V O R Z D Q G
W X U Q V R I I D I W H U W K H H Q J L Q H L V Z D U P
, I W K H O R Z H Q J L Q H F R R O D Q W W H P S H U D W X U H
L Q G L F D W R U O L J K W U H P D L Q V L O O X P L Q D W H G D I W H U
W K H H Q J L Q H K D V E H H Q V X I I L F L H Q W O \ Z D U P H G
X S W K H W H P S H U D W X U H V H Q V R U F R X O G K D Y H D
P D O I X Q F W L R Q & R Q V X O W D Q H [ S H U W U H S D L U H U
Z H U H F R P P H Q G D Q $ X W K R U L V H G 0 D ] G D
5 H S D L U H U
: K H Q ' U L Y L Q J
, Q V W U X P H Q W & O X V W H U D Q G ' L V S O D \
6 R P H P R G H O V
Page 321 of 759
¾The front doors or the boot is not fully closed.
¾The vehicle is on a road incline.
¾The door mirrors are retracted.
¾Do not hit the front/rear camera, front bumper, and door mirrors forcefully. The camera
position or installation angle may shift.
¾The cameras are of a waterproof structure. Do not disassemble, modify, or remove a
camera.
¾The camera cover is made of hard plastic, therefore do not apply oil film remover, organic
solvents, wax, or coating agents. If any such agent gets on the camera cover, wipe it off
using a soft cloth immediately.
¾Do not rub the camera lens forcefully, or clean it with an abrasive or hard brush. Otherwise,
it could scratch the camera lens and negatively affect the images.
¾Consult an expert repairer (we recommend an Authorised Mazda Repairer) for repair,
painting, or replacement of the front/rear camera, front bumper and door mirrors.
¾Heed the following cautions to assure that the 360°View Monitor operates normally.
¾Do not modify the vehicle suspensions or lower/raise the vehicle body, or both.
¾Always use wheels of the specified type and size for the front and rear wheels. Consult an
expert repairer (we recommend an Authorised Mazda Repairer) for tyre replacement.
¾When the display is cold, images may leave trails or the screen might be darker than usual,
making it difficult to check the vehicle surroundings. Always confirm the safety at the front
and around the vehicle visually when driving.
¾The method for parking/stopping the vehicle using the 360°View Monitor differs depending
on the road circumstances/conditions and the vehicle conditions. When and how much you
turn the steering wheel will differ depending on the situation, , therefore always check the
vehicle surroundings directly with your eyes while using the system.
Also, before using the system, always make sure that the vehicle can be parked/stopped in
the parking/stopping space.
NOTE
xIf there are water droplets, snow, or mud on the camera lens, wipe it off using a soft cloth.
If the camera lens is especially dirty, wash it off with mild detergent.
xIf the area where the camera is installed, such as the boot (Saloon)/rear bumper
(Hatchback) or door mirrors, has been damaged in a vehicle accident, the camera
(position, installation angle) may have shifted. Always consult an expert repairer (we
recommend an Authorised Mazda Repairer) to have the vehicle inspected.
xIf the camera is subjected to excessive changes in temperature such as by pouring hot
water on the camera during cold weather, the 360°View Monitor may not operate
normally.
xIf the battery voltage is low, the screen might be temporarily difficult to view, however,
this does not indicate a problem.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 348 of 759
¾Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area around
it. If the Forward Sensing Camera (FSC) is severely hit or if there are cracks or damage
caused by
flying gravel or debris in the area around it, stop using the following systems
and consult an expert repairer (we recommend an Authorised Mazda Repairer).
¾High Beam Control System (HBC)
¾Adaptive LED Headlights (ALH)
¾Lane Departure Warning System (LDWS)
¾Driver Attention Alert (DAA)
¾Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS)
¾Traffic Sign Recognition System (TSR)
¾Advanced Smart City Brake Support (Advanced SCBS)
¾Smart City Brake Support [Forward] (SCBS F)
¾Smart Brake Support (SBS)
¾The direction in which the Forward Sensing Camera (FSC) is pointed has been finely
adjusted. Do not change the installation position of the Forward Sensing Camera (FSC) or
remove it. Otherwise, it could result in damage or malfunction.
¾Always use tyres for all wheels that are of the
specified size, and the same manufacturer,
brand, and tread pattern. In addition, do not use tyres with significantly different wear
patterns on the same vehicle as the system may not operate normally.
¾The Forward Sensing Camera (FSC) includes a function for detecting a soiled windscreen
and informing the driver, however, depending on the conditions, it may not detect plastic
shopping bags, ice or snow on the windscreen. In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive carefully
and pay attention to the road ahead.
NOTE
xIn the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
xThe height of the vehicle ahead is low.
xYou drive your vehicle at the same speed as the vehicle ahead.
xHeadlights are not turned on during the night or when going through a tunnel.
xIn the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
xUnder bad weather condition, such as rain, fog and snow.
xThe window washer is being used or the windscreen wipers are not used when it's
raining.
xIce, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on the
windscreen.
xTrucks with low loading platforms and vehicles with an extremely low or high profile.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 353 of 759
& $ 8 7 , 2 1
Heed the following precautions to assure correct operation of each system.
¾Do not adhere stickers (including transparent stickers) to the surface of the radiator grille
and front emblem in and around the radar sensor (front), and do not replace the radiator
grille and front emblem with any product that is not a genuine product designed for use
with the radar sensor (front).
¾The radar sensor (front) includes a function for detecting soiling of the radar sensor's front
surface and informing the driver, however, depending on the conditions, it may require
time to detect or it may not detect plastic shopping bags, ice or snow. If this occurs, the
system may not operate correctly, therefore always keep the radar sensor (front) clean.
¾Do not install a grille guard.
¾If the front part of the vehicle has been damaged in a vehicle accident, the position of the
radar sensor (front) may have moved. Stop the system immediately and always have the
vehicle inspected at an expert repairer (we recommend an Authorised Mazda Repairer).
¾Do not use the front bumper to push other vehicles or obstructions such as when pulling
out of a parking space. Otherwise, the radar sensor (front) could be hit and its position
deviated.
¾Do not remove, disassemble, or modify the radar sensor (front).
¾For repairs, replacement or paint work around the radar sensor (front), consult an expert
repairer (we recommend an Authorised Mazda Repairer).
¾Do not modify the suspension. If the suspension are
modified, the vehicle's posture could
change and the radar sensor (front) may not be able to correctly detect a vehicle ahead or
an obstruction.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 354 of 759
NOTE
xUnder the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions
correctly and each system may not
operate normally.
xThe rear surface of a vehicle ahead
does not reflect radio waves
effectively, such as an unloaded
trailer or an automobile with a
loading platform covered by a soft
top, vehicles with a hard plastic
tailgate, and round-shaped vehicles.
xVehicles ahead with low vehicle
height and thus less area for
reflecting radio waves.
xVisibility is reduced due to a vehicle
ahead casting off water, snow, or
sand from its tyres and onto your
windscreen.
xThe boot/luggage compartment is
loaded with heavy objects or the rear
passenger seats are occupied.
xIce, snow, or soiling is on the front
surface of the front emblem.
xDuring inclement weather such as
rain, snow, or sand storms.
xWhen driving near facilities or
objects emitting strong radio waves.
xUnder the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions.
xThe beginning and end of a curve.
xRoads with continuous curves.
xNarrow lane roads due to road
construction or lane closures.
xThe vehicle ahead enters the radar
sensor's blind spot.
xThe vehicle ahead is running
abnormally due to accident or
vehicle damage.
xRoads with repeated up and down
slopes
xDriving on poor roads or unpaved
roads.
xThe distance between your vehicle
and the vehicle ahead is extremely
short.
xA vehicle suddenly comes close such
as by cutting into the lane.
xTo prevent incorrect operation of the
system, use tyres of the same specified
size, manufacturer, brand, and tread
pattern on all 4 wheels. In addition, do
not use tyres with significantly different
wear patterns or tyre pressures on the
same vehicle (Including the temporary
spare tyre).
xIf the battery power is weak, the system
may not operate correctly.
xIf the vehicle is driven on a road with
little traffic and few vehicles ahead or
obstructions for the radar sensor
(front) to detect, the sensor detects that
the radar sensor (front) is dirty and the
Smart Brake Support/Smart City Brake
Support (SBS/SCBS) Warning Light
(amber) may be temporarily turned on.
However, it does not indicate a
malfunction.
xThe radar sensors are regulated by the
relevant radio wave laws of the country
in which the vehicle is driven. If the
vehicle is driven abroad, authorization
from the country in which the vehicle is
driven may be required.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 578 of 759
( Q J L Q H & R P S D U W P H Q W 2 Y H U Y L H Z
Windscreen washer fluid reservoir Brake/Clutch fluid reservoir
Engine oil dipstick Battery
Fuse block
Cooling system capEngine coolant reservoirEngine oil-filler cap SKYACTIV-G 1.3 and SKYACTIV-G 1.5
0 D L Q W H Q D Q F H D Q G & D U H
2 Z Q H U 0 D L Q W H Q D Q F H