2019 MAZDA MODEL 2 brake light

&$87,21
In the following cases, turn the system off to prevent a mis-operation:
¾The vehicle is being towed or when towing another vehicle.
¾The vehicle is on a chassis roller.
¾When driving on rough roads such as in areas of dense grass or off-road.
Refer to Stopping the Smart City Brake Support [Forward] (SCBS F) system Operation on page
4-170 on how to turn off the SCBS F system.
NOTE
xThe SCBS F system will operate under the following conditions.
xThe engine is running.
xThe Smart Brake Support/Smart City Brake Support (SBS/SCBS) system warning light
(amber) does not illuminate.
x(Rear-end collision warning)
The vehicle speed is about 4 to 80 km/h (2 to 50 mph).
x(Brake control (Smart City Brake Support (SCBS) brake))
The vehicle speed is about 4 to 30 km/h (2 to 18 mph).
xThe SCBS F system is not turned off.
xUnder the following conditions, the SCBS F system may not operate normally:
xThe SCBS F system will not operate if the driver is deliberately performing driving
operations (accelerator pedal and steering wheel).
xIf there is the possibility of partial contact with a vehicle ahead.
xThe vehicle is driven on a slippery road surface such as wet roads or icy or snow-bound
roads.
xThe braking performance is adversely affected due to cold temperatures or wet brakes.
xThe vehicle is driven at the same speed as the vehicle ahead.
xThe accelerator pedal is depressed.
xThe brake pedal is depressed.
xThe steering wheel is being operated.
xThe selector lever is being operated.
xIn the following cases, the Forward Sensing Camera (FSC) determines that there is a
vehicle ahead and the SCBS F may operate.
xObjects on the road at the entrance to a curve.
xVehicles passing in the opposite lane while making a curve.
xMetal objects, bumps, or protruding objects on the road.
xWhen passing through a toll gate.
xWhen passing through low gates, narrow gates, car washing machines, or tunnels.
:KHQ'ULYLQJ
L$&7,96(16(


¾If ice or snow is stuck on the ultrasonic sensors (rear) they may not be able to detect
obstructions correctly depending on the conditions. In such cases, the system may not be
able to perform controls correctly. Always drive carefully and pay attention to the rear of
the vehicle.
NOTE
xThe vehicle posture changes depending on the accelerator pedal, brake pedal and
steering wheel operations, which could make it difficult for the system to recognise an
obstruction, or it could facilitate unnecessary detection. In such cases, the SCBS R may or
may not operate.
xThe SCBS R system will operate under the following conditions.
xThe Smart City Brake Support (SCBS) warning light (amber) does not illuminate.
xThe engine is running.
xThe change lever (manual transaxle vehicle) or the selector lever (automatic transaxle
vehicle) is in the R (reverse) position.
xThe vehicle speed is between about 2 to 8 km/h (2 to 4 mph).
xThe SCBS R is not turned off.
xThe DSC is not malfunctioning.
xThe SCBS R operates using ultrasonic sensors (rear) which detect obstructions at the rear
by emitting ultrasonic waves and then receiving the returning waves reflected off the
obstructions.
xIn the following cases, the ultrasonic sensors (rear) cannot detect obstructions and the
SCBS R may not operate.
xThe height of the obstruction is low such as low walls or trucks with low loading
platforms.
xThe height of the obstruction is high such as trucks with high loading platforms.
xThe obstruction is small.
xThe obstruction is thin such as a signpost.
xThe obstruction is positioned away from the centre of the vehicle.
xThe surface of the obstruction is not pointed vertically relative to the vehicle.
xThe obstruction is soft such as a hanging curtain or snow stuck to a vehicle.
xThe obstruction is shaped irregularly.
xThe obstruction is extremely close.
:KHQ'ULYLQJ
L$&7,96(16(


xIn the following cases, the ultrasonic sensors (rear) cannot detect obstructions correctly
and the SCBS R may not operate.
xSomething is stuck on the bumper near an ultrasonic sensor (rear).
xThe steering wheel is turned sharply, or the brake or accelerator pedal is operated.
xThere is another obstruction near one obstruction.
xDuring inclement weather such as rain, fog and snow.
xHigh or low humidity.
xHigh or low temperatures
xStrong winds.
xThe path of travel is not flat.
xHeavy luggage is loaded in the luggage compartment or on the rear seat.
xObjects such as a wireless aerial, fog light, or illuminated number plate is installed
near an ultrasonic sensor (rear).
xThe orientation of an ultrasonic sensor (rear) has deviated for reasons such as a
collision.
xThe vehicle is affected by other sound waves such as the horn, engine noise, ultrasonic
sensor of another vehicle.
xIn the following cases, an ultrasonic sensor (rear) may detect something as a target
obstruction which could cause the SCBS R system to operate.
xDriving on a steep slope.
xWheel blocks.
xHanging curtains, gate poles such as at toll gates and railroad crossing.
xWhen travelling near objects such as foliage, barriers, vehicles, walls, and fences along
a road.
xWhen driving off-road in areas where there is grass and forage.
xWhen passing through low gates, narrow gates, car washing machines, and tunnels.
xA towing bar is installed or a trailer is connected.
x(Manual transaxle)
If the vehicle is stopped by the Smart City Brake Support (SCBS) operation and the clutch
pedal is not depressed, the engine stops.
xThe Smart City Brake Support (SCBS) warning indication (amber) turns on when the
system has a malfunction.
Refer to Warning Lights on page 4-39.
:KHQ'ULYLQJ
L$&7,96(16(


6PDUW%UDNH6XSSRUW
6%6

7KH6%6V\VWHPDOHUWVWKHGULYHURID
SRVVLEOHFROOLVLRQXVLQJDGLVSOD\DQG
ZDUQLQJVRXQGLIWKHUDGDUVHQVRUIURQW
DQGWKH)RUZDUG6HQVLQJ&DPHUD)6&
GHWHUPLQHWKDWWKHUHLVWKHSRVVLELOLW\RID
FROOLVLRQZLWKDYHKLFOHDKHDGZKLOHWKH
YHKLFOHLVEHLQJGULYHQDWDERXWNPKRU
IDVWHUPSKRUIDVWHU)XUWKHUPRUHLI
WKHUDGDUVHQVRUIURQWDQGWKH)RUZDUG
6HQVLQJ&DPHUD)6&GHWHUPLQHVWKDWD
FROOLVLRQLVXQDYRLGDEOHWKHDXWRPDWLF
EUDNHFRQWUROLVSHUIRUPHGWRUHGXFH
GDPDJHLQWKHHYHQWRIDFROOLVLRQ
,QDGGLWLRQZKHQWKHGULYHUGHSUHVVHVWKH
EUDNHSHGDOWKHEUDNHVDUHDSSOLHGILUPO\
DQGTXLFNO\WRDVVLVW%UDNH$VVLVW6%6
EUDNHDVVLVW
:$ 5 1 , 1 *
Do not rely completely on the SBS system
and always drive carefully:
The SBS is designed to reduce damage in
the event of a collision, not avoid an
accident. The ability to detect an
obstruction is limited depending on the
obstruction, weather conditions, or traffic
conditions. Therefore, if the accelerator
pedal or brake pedal is mistakenly
operated it could result in an accident.
Always verify the safety of the surrounding
area and depress the brake pedal or
accelerator pedal while keeping a safer
distance from vehicles ahead or on-coming
vehicles.
&$87,21
In the following cases, turn the system off
to prevent a mis-operation:
¾The vehicle is being towed or when
towing another vehicle.
¾The vehicle is on a chassis roller.
¾When driving on rough roads such as in
areas of dense grass or off-road.
NOTE
xThe SBS system operates when all of the
following conditions are met:
xThe ignition is switched ON.
xThe SBS system is on.
xThe vehicle speed is about 15 km/h or
faster (10 mph or faster).
xThe relative speed between your
vehicle and the vehicle ahead is about
15 km/h or faster (10 mph or faster).
xThe Dynamic Stability Control (DSC)
is not operating.
xThe SBS system may not operate under
the following conditions:
xIf the vehicle is accelerated rapidly
and it comes close to a vehicle ahead.
xThe vehicle is driven at the same
speed as the vehicle ahead.
xThe accelerator pedal is depressed.
xThe brake pedal is depressed.
xThe steering wheel is being operated.
xThe selector lever is being operated.
xThe direction indicator is being used.
xWhen the vehicle ahead is not
equipped with tail lights or the tail
lights are turned off.
:KHQ'ULYLQJ
L$&7,96(16(

6RPHPRGHOV

¾Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area around
it. If the Forward Sensing Camera (FSC) is severely hit or if there are cracks or damage
caused by
flying gravel or debris in the area around it, stop using the following systems
and consult an expert repairer (we recommend an Authorised Mazda Repairer).
¾High Beam Control System (HBC)
¾Adaptive LED Headlights (ALH)
¾Lane Departure Warning System (LDWS)
¾Driver Attention Alert (DAA)
¾Lane-keep Assist System (LAS) & Lane Departure Warning System (LDWS)
¾Traffic Sign Recognition System (TSR)
¾Advanced Smart City Brake Support (Advanced SCBS)
¾Smart City Brake Support [Forward] (SCBS F)
¾Smart Brake Support (SBS)
¾The direction in which the Forward Sensing Camera (FSC) is pointed has been finely
adjusted. Do not change the installation position of the Forward Sensing Camera (FSC) or
remove it. Otherwise, it could result in damage or malfunction.
¾Always use tyres for all wheels that are of the
specified size, and the same manufacturer,
brand, and tread pattern. In addition, do not use tyres with significantly different wear
patterns on the same vehicle as the system may not operate normally.
¾The Forward Sensing Camera (FSC) includes a function for detecting a soiled windscreen
and informing the driver, however, depending on the conditions, it may not detect plastic
shopping bags, ice or snow on the windscreen. In such cases, the system cannot accurately
determine a vehicle ahead and may not be able to operate normally. Always drive carefully
and pay attention to the road ahead.
NOTE
xIn the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
xThe height of the vehicle ahead is low.
xYou drive your vehicle at the same speed as the vehicle ahead.
xHeadlights are not turned on during the night or when going through a tunnel.
xIn the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
xUnder bad weather condition, such as rain, fog and snow.
xThe window washer is being used or the windscreen wipers are not used when it's
raining.
xIce, fog, snow, frost, rainfall, dirt, or foreign matter such as a plastic bag is stuck on the
windscreen.
xTrucks with low loading platforms and vehicles with an extremely low or high profile.
:KHQ'ULYLQJ
L$&7,96(16(


xIf the Forward Sensing Camera (FSC) cannot operate normally due to backlight or fog,
the system functions related to the Forward Sensing Camera (FSC) are temporarily
stopped and the following warning lights turn on. However, this does not indicate a
malfunction.
xHigh Beam Control System (HBC) warning light (amber)
xAdaptive LED Headlights (ALH) warning light (amber)
xLane Departure Warning System (LDWS) warning light
xLane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
xSmart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
xIf the Forward Sensing Camera (FSC) cannot operate normally due to high temperatures,
the system functions related to the Forward Sensing Camera (FSC) are temporarily
stopped and the following warning lights turn on. However, this does not indicate a
malfunction. Cool down the area around the Forward Sensing Camera (FSC) such as by
turning on the air conditioner.
xHigh Beam Control System (HBC) warning light (amber)
xAdaptive LED Headlights (ALH) warning light (amber)
xLane Departure Warning System (LDWS) warning light
xLane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
xSmart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
xIf the Forward Sensing Camera (FSC) detects that the windscreen is dirty or foggy, the
system functions related to the Forward Sensing Camera (FSC) are temporarily stopped
and the following warning lights turn on. However, this does not indicate a problem.
Remove the dirt from the windscreen or press the defroster switch and defog the
windscreen.
xHigh Beam Control System (HBC) warning light (amber)
xAdaptive LED Headlights (ALH) warning light (amber)
xLane Departure Warning System (LDWS) warning light
xLane-keep Assist System (LAS) & Lane Departure Warning System (LDWS) warning
light
xSmart Brake Support/Smart City Brake Support (SBS/SCBS) warning light (amber)
xIf there are recognizable cracks or damage caused by flying gravel or debris on the
windscreen, always have the windscreen replaced. Consult an expert repairer (we
recommend an Authorised Mazda Repairer) for replacement.
:KHQ'ULYLQJ
L$&7,96(16(


NOTE
xUnder the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions
correctly and each system may not
operate normally.
xThe rear surface of a vehicle ahead
does not reflect radio waves
effectively, such as an unloaded
trailer or an automobile with a
loading platform covered by a soft
top, vehicles with a hard plastic
tailgate, and round-shaped vehicles.
xVehicles ahead with low vehicle
height and thus less area for
reflecting radio waves.
xVisibility is reduced due to a vehicle
ahead casting off water, snow, or
sand from its tyres and onto your
windscreen.
xThe boot/luggage compartment is
loaded with heavy objects or the rear
passenger seats are occupied.
xIce, snow, or soiling is on the front
surface of the front emblem.
xDuring inclement weather such as
rain, snow, or sand storms.
xWhen driving near facilities or
objects emitting strong radio waves.
xUnder the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions.
xThe beginning and end of a curve.
xRoads with continuous curves.
xNarrow lane roads due to road
construction or lane closures.
xThe vehicle ahead enters the radar
sensor's blind spot.
xThe vehicle ahead is running
abnormally due to accident or
vehicle damage.
xRoads with repeated up and down
slopes
xDriving on poor roads or unpaved
roads.
xThe distance between your vehicle
and the vehicle ahead is extremely
short.
xA vehicle suddenly comes close such
as by cutting into the lane.
xTo prevent incorrect operation of the
system, use tyres of the same specified
size, manufacturer, brand, and tread
pattern on all 4 wheels. In addition, do
not use tyres with significantly different
wear patterns or tyre pressures on the
same vehicle (Including the temporary
spare tyre).
xIf the battery power is weak, the system
may not operate correctly.
xIf the vehicle is driven on a road with
little traffic and few vehicles ahead or
obstructions for the radar sensor
(front) to detect, the sensor detects that
the radar sensor (front) is dirty and the
Smart Brake Support/Smart City Brake
Support (SBS/SCBS) Warning Light
(amber) may be temporarily turned on.
However, it does not indicate a
malfunction.
xThe radar sensors are regulated by the
relevant radio wave laws of the country
in which the vehicle is driven. If the
vehicle is driven abroad, authorization
from the country in which the vehicle is
driven may be required.
:KHQ'ULYLQJ
L$&7,96(16(


xUnder extremely hot or cold weather conditions.
xThe vehicle is driven on bumps, inclines, gravel, or grass covered roads.
xAnything which generates ultrasound is near the vehicle, such as another vehicle's
horn, the engine sound of a motorcycle, the air brake sound of a large-sized vehicle, or
another vehicle's sensors.
xThe vehicle is driven in heavy rain or in road conditions causing water-splash.
xA commercially-available wing pole or an aerial for a radio transmitter is installed to
the vehicle.
xThe vehicle is moving towards a tall or square curbstone.
xAn obstruction is too close to the sensor.
xObstructions under the bumper may not be detected. Obstructions that are lower than the
bumper or thin which may have been initially detected may no longer be detected as the
vehicle approaches more closely to the obstruction.
xThe following types of obstructions may not be detected:
xThin objects such as wire or rope
xThings which absorb sonic waves easily such as cotton or snow
xAngular shaped objects
xVery tall objects, and those which are wide at the top
xSmall, short objects
xAlways have the system inspected at an expert repairer (we recommend an Authorised
Mazda Repairer) if any shock is applied to the bumpers, even in a minor accident. If the
sensors are deviated, they cannot detect obstructions.
x(With front sensor and front corner sensor)
The system may have a malfunction if the beep does not operate or the indicator light
does not illuminate when the park assist sensors switch is turned on. Consult an expert
repairer (we recommend an Authorised Mazda Repairer).
x(Without front sensor and front corner sensor)
The system may have a malfunction if the beep does not operate. Consult an expert
repairer (we recommend an Authorised Mazda Repairer).
x(With front sensor and front corner sensor)
The system may have a malfunction if the beep sound which indicates a system
malfunction is heard and the indicator light flashes. Consult an expert repairer (we
recommend an Authorised Mazda Repairer).
xThe beeper which indicates a system malfunction may not be heard if the ambient
temperature is extremely cold, or mud, ice, or snow adheres to the sensor area. Remove
any foreign material from the sensor area.
:KHQ'ULYLQJ
3DUNLQJ6HQVRU6\VWHP