2019 INFINITI QX50 Owners Manual

COAT HOOKS
The coat hooks, located on the side pillars of
the 2nd row, may be used to store coats and
other articles of clothing.
CAUTION
Do not apply a total load of more than
7.3 lbs. (3.3 kg) to a single coat hook.
ROOF RACK (if so equipped)
Do not apply any load directly to the roof side
rails. Cross bars must be installed before ap-
plying load/cargo/luggage to the roof of the
vehicle. Genuine NISSAN accessory cross
bars are available through an INFINITI re-
tailer. It is recommended that you visit an
INFINITI retailer for additional information.
The service load capacity for the roof side
rails is 165 lbs. (74 kg), however do not ex-
ceed the accessory cross bars load capacity.
Be careful that your vehicle does not exceed
the Gross Vehicle Weight Rating (GVWR) or
its Gross Axle Weight Rating (GAWR frontand rear). The GVWR and GAWR are located
on the F.M.V.S.S. or C.V.M.S.S. certification
label (located on the driver’s door pillar). For
additional information regarding GVWR and
GAWR, refer to “Vehicle loading information”
in the “Technical and consumer information”
section of this manual.
WARNING
∙ Always install the cross bars onto the
roof side rails before loading cargo of any
kind. Loading cargo directly onto the
roof side rails or the vehicle’s roof may
cause vehicle damage.
∙ Drive extra carefully when the vehicle is loaded at or near the cargo carrying ca-
pacity, especially if the significant por-
tion of that load is carried on the cross
bars.
∙ Heavy loading of the cross bars has the potential to affect the vehicle stability
and handling during sudden or unusual
handling maneuvers.
∙ Roof rack cross bars should be evenly distributed.
∙ Do not exceed maximum roof rack cross bars load capacity.
LIC3943LIC2386
Instruments and controls2-61

∙ Properly secure all cargo with ropes orstraps to help prevent it from sliding or
shifting. In a sudden stop or collision, un-
secured cargo could cause personal
injury.
Installing crossbars (if so equipped)
WARNING
∙ It is recommended that you have the roofrack crossbars installed by an INFINITI
retailer.
∙ Make sure the moonroof is in the closed position during the installation process.
∙ Protect the painted area on the vehicle’s roof under the crossbars by placing a
piece of cloth under the cross bars to pre-
vent scratch damage.
∙ Do not load the crossbars more than the rated load capacity and always distribute
the load uniformly.
The roof rack crossbars may be installed or
removed. Use the TORX® provided wrench in
the tool kit to install and remove the cross-
bars. The TORX® wrench will be in the glove
box. 1. Manually remove the protective covers
from the roof rails.
2. Using a quarter, rotate the key-slot coun-
terclockwise to remove the plastic cover.
LIC3890LIC3891
2-62Instruments and controls

3. Use the TORX® provided wrench to loosen
the clamp screw.4. Open the clamp approximately two inches
to minimize potential scratching of the roof
rails.5. Determine crossbar orientation by locating
the arrow that points to the front of the
vehicle.
LIC3892LIC3893LIC3894
Instruments and controls2-63

6. Align the pins of the passenger side clamp
with the holes in the roof rail.7. While holding the inner clamp, use the
TORX® provided wrench to tighten the
clamping screw.
NOTE:
Using the TORX® provided wrench, tighten
to 10 N•m (7.4 ft.-lbs.).8. Tighten both the driver and passenger side
shoulder screw.
NOTE:
Using the TORX® provided wrench, tighten
to 10 N•m (7.4 ft.-lbs.).
LIC3895LIC3896LIC3897
2-64Instruments and controls

9. Assemble the plastic cover. Slide the cover
over the crossbar.10. Ensure the cover is in the final position. 11. Using a quarter, turn the key-slot clock-
wise to lock the plastic cover.
NOTE:
After assembling both the front and rear
crossbars, wiggle the crossbars by hand to
check for loose parts. If either crossbar is
loose, remove the crossbars and repeat
steps 1–11 carefully.
LIC3898LIC3899LIC3900
Instruments and controls2-65

POWER WINDOWS
WARNING
∙ Make sure that all passengers have theirhands, etc., inside the vehicle while it is in
motion and before closing the windows.
Use the window lock switch to prevent
unexpected use of the power windows.
∙ To help avoid risk of injury or death through unintended operation of the ve-
hicle and/or its systems, including en-
trapment in windows or inadvertent door
lock activation, do not leave children,
people who require the assistance of oth-
ers or pets unattended in your vehicle.
Additionally, the temperature inside a
closed vehicle on a warm day can quickly
become high enough to cause a signifi-
cant risk of injury or death to people and
pets.
The power windows operate when the igni-
tion switch is placed in the ON position or for
a period of time after the ignition switch is
placed in the OFF position. If the driver’s or
passenger’s door is opened during this period
of time, the power to the windows is can-
celed.
1. Driver side automatic switch
2. Front passenger side automatic switch
3. Left rear passenger automatic
switch
4. Right rear passenger automatic
switch
5. Window lock button
Driver’s side power window switch
The driver’s side control panel is equipped
with switches to open or close the front and
rear passenger windows.
The window can be partially opened by push-
ing the switch
Adown lightly until the de-
sired window position is reached. To close
the window partially, pull the switch
Bup
until the desired window position is reached.
Locking passengers’ windows
When the window lock buttonCis de-
pressed, only the driver’s side window can be
opened or closed. Press it again to cancel the
window lock function.
SIC4352
WINDOWS
2-66Instruments and controls

Front passenger’s power window
switch
The passenger’s window switch operates
only the corresponding passenger’s window.
To open the window partially, push the
switch down lightly until the desired window
position is reached. To close the window par-
tially, pull the switch up until the desired win-
dow position is reached.
Rear power window switch
The rear power window switches open or
close only the corresponding windows. To
partially open the window, push the switch
down lightly until the desired window posi-
tion is reached. To partially close the window,
pull the switch up lightly until the desired
window position is reached.
Automatic operation
To fully open a window equipped with auto-
matic operation, push the window switch
down to the second detent and release it; it
need not be held. The window automatically
opens all the way. To stop the window, lift
the switch up while the window is opening.
To fully close a window equipped with auto-
matic operation, pull the switch up to the
second detent and release it; it need not be
held. To stop the window, push the switch
down while the window is closing.
SIC4353LIC0410LIC0410
Instruments and controls2-67

Auto-reverse function
The auto-reverse function can be activated
when a window is closed by automatic op-
eration.
Depending on the environment or driving
conditions, the auto-reverse function may
be activated if an impact or load similar to
something being caught in the window oc-
curs.
WARNING
There are some small distances immedi-
ately before the closed position which can-
not be detected. Make sure that all passen-
gers have their hands, etc., inside the
vehicle before closing the window.
If the vehicle’s battery is disconnected, re-
placed, or jump started, the power window
auto-reverse function may not operate prop-
erly. If this occurs, it is recommended that you
visit an INFINITI retailer to re-initialize the
power window auto-reverse system.
If the control unit detects something caught
in a window equipped with automatic opera-
tion as it is closing, the window will be imme-
diately lowered.
POWER MOONROOF
The front moonroof is a power moonroof,
the rear moonroof is fixed glass. The power
moonroof will only operate when the ignition
switch is placed in the ON position. The
moonroof is operational for a period of time,
even if the ignition switch is placed in the OFF
position. If the driver’s door or the front pas-
senger’s door is opened during this period of
time, the power to the moonroof is canceled.
Sliding the moonroof
To slide the moonroof:
∙ To fully open the moonroof, push the switch
1toward the open position until
it reaches the second detent. If the
switch
1is pushed to the first detent,
only the sunshade will open.
∙ To fully close the moonroof, push the switch
2toward the close position until
it reaches the second detent. If the
switch
2is pushed to the first detent, the
moonroof will close but the sunshade will
remain open.
∙ To stop the moonroof during operation, push the
1,2or3switch to the de-
sired position.
Tilting the moonroof
To tilt up, push the moonroof switch3.To
tilt down the moonroof, push the switch
3,
or the switch
2to the first detent. When the
switch
2is pushed to the second detent, the
moonroof will tilt down and the sunshade will
close.
LIC3912
MOONROOF (if so equipped)
2-68Instruments and controls