2019 INFINITI QX30 hood open

the driver's door opening, see "Tire and load-
ing information label". The low tire pressure
warning light does not automatically turn
off when the tire pressure is adjusted. After
the tire is inflated to the recommended pres-
sure, the vehicle must be driven at speeds
above 16 MPH (25 km/h) to activate the
TPMS and turn off the low tire pressure
warning light. Use a tire pressure gauge to
check the tire pressure.
The low tire pressure warning message ap-
pears each time the ignition switch is placed
in the ON position as long as the low tire
pressure warning light remains illuminated.
For additional information, see "Vehicle in-
formation display" later in this section and
"Tire Pressure Monitoring System (TPMS)".
TPMS malfunction:
If the TPMS is not functioning properly, the
low tire pressure warning light will flash for
approximately 1 minute when the ignition
switch is placed in the ON position. The light
will remain on after 1 minute. Have the sys-
tem checked. It is recommended that you visit
an INFINITI retailer for this service. The low
tire pressure warning does not appear if the
low tire pressure warning light illuminates to
indicate a TPMS malfunction.
For additional information, see "Tire Pressure
Monitoring System (TPMS)".WARNING
•Radio waves could adversely affect
electric medical equipment. Those who
use a pacemaker should contact the
electric medical equipment manufac-
turer for the possible influences before
use.
•If the light does not illuminate with the
ignition switch pushed ON, have the ve-
hicle checked. It is recommended you
visit an INFINITI retailer for this service.
•If the light illuminates while driving,
avoid sudden steering maneuvers or
abrupt braking, reduce vehicle speed,
pull off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and in-
crease the likelihood of tire failure. Seri-
ous vehicle damage could occur and may
lead to an accident and could result in
serious personal injury or death. Check
the tire pressure for all four tires. Adjust
the tire pressure to the recommended
COLD tire pressure shown on the tire
placard, located in the driver's door
opening, to turn the low tire pressure
warning light off. If the light still illumi-
nates while driving after adjusting the
tire pressure, a tire may be flat. If youhave a flat tire, replace it with a replace-
ment tire as soon as possible.
•If a replacement tire is mounted or a
wheel is replaced without a TPMS sen-
sor tire pressure will not be indicated,
the TPMS will not function and the low
tire pressure warning light will flash for
approximately 1 minute. The light will
remain on after 1 minute. Have your ve-
hicle's tires replaced and/or TPMS sys-
tem reset as soon as possible. It is rec-
ommended you visit an INFINITI retailer
for these services.
•Replacing tires with those not originally
specified by INFINITI could affect the
proper operation of the TPMS.
CAUTION
•The TPMS is not a substitute for the
regular tire pressure check. Be sure to
check the tire pressure regularly.
•If the vehicle is being driven at speeds of
less than 16 MPH (25 km/h), the TPMS
may not operate correctly.
•Be sure to install the specified size of
tires to all four wheels correctly.
2-10Instruments and controls

If the seat belt warning light flashes, together
with an intermittent warning tone, this means
that the driver or passenger has not fastened
their seat belt, and the speed of the vehicle is
exceeding 15 MPH (25 km/h).
Supplemental Restraint
System (SRS) air bag
warning light
WARNING
If the supplemental air bag warning light is
on, it could mean that the front air bag,
driver's knee air bag, side air bag, curtain
air bag and/or pretensioner systems will
not operate in an accident. To help avoid
injury to yourself or others, have your ve-
hicle checked by an INFINITI retailer as
soon as possible.
When the ignition switch is in the ON posi-
tion, the Supplemental Restraint System
(SRS) air bag warning light illuminates to in-
dicate that the system is operational. The
light then tuns off within a few seconds after
the engine is started.
If any of the following conditions occur, the
front air bag, front seat-mounted side-
impact air bag, roof-mounted curtain air bag
and pretensioner systems need servicing:
•The supplemental air bag warning light
remains on for longer than a few seconds
once the engine is running.
•The supplemental air bag warning light
flashes intermittently.
•The supplemental air bag warning light
does not come on at all.
It is recommended you visit an INFINITI re-
tailer for these services. Unless checked and
repaired, the supplemental restraint system
(air bag system) and/or the pretensioner sys-
tems may not function properly. For addi-
tional information, refer to "Supplemental
Restraint System (SRS)".
Coolant warning light
WARNING
If the coolant warning light is lit, the engine
may not be being cooled sufficiently and
may be damaged.
Never drive with an overheated engine.
Driving when your engine is overheated can
cause some fluids which may have leaked
into the engine compartment to catch fire.
In addition, steam from an overheated en-
gine can cause serious burns, which can oc-
cur just by opening the hood.
There is a risk of injuryIf the red coolant warning light lights up while
the engine is running and the coolant tem-
perature gauge is at the start of the scale, the
temperature sensor for the coolant tempera-
ture gauge is faulty. The coolant temperature
is no longer being monitored. There is a risk of
engine damage if the coolant temperature is
too high.
Stop the vehicle immediately, paying atten-
tion to road and traffic conditions, and switch
off the engine. Do not continue driving under
any circumstances.
Consult an INFINITI retailer.
If the red coolant warning light comes on
while the engine is running, with or without
an accompanying warning tone, it could
mean that:
•The coolant level is too low.
•If the coolant level is correct, the airflow to
the engine radiator may be blocked or the
electric engine radiator fan may be mal-
functioning.
•The coolant is too hot and the engine is no
longer being cooled sufficiently.
Observe the additional display messages in
the vehicle information display.
2-12Instruments and controls

Idle Stop/Start System reminder
chime (if equipped)
The engine will shift to the normal stopped
state if any of the following operations is
made during Idle Stop/Start System activa-
tion, and the Idle Stop/Start System chime
will sound if:
– The vehicle engine hood is open.
When the above condition continues for over
3 minutes the Idle Stop/Start System chime
will sound in 5-minute intervals as a reminder
to prevent the possibility of a discharged bat-
tery. Use the ignition switch to turn off the
engine.
Close the hood or the driver’s door, or fasten
the seat belt then restart the engine using the
ignition switch.
For more information, see " Idle Stop/Start
System (if equipped)".The vehicle information display
1is located
between the tachometer and the speedom-
eter.1Permanent display: depending on vehicle
specification: outside temperature or
speed
2Time
3Text field
4Menu bar
5Drive program
6Shift lever position
Text field
3shows the selected menu or
submenu as well as display messages.
NOTE
Set the time using the INFINITI controller
and the [Settings] menu available in the
central display (see your INFINITI InTouch
Owner's Manual).
NIC2751NIC2752
VEHICLE INFORMATION DISPLAY
Instruments and controls2-15

Message Possible causes/consequences and solutions
The lift gate is open.
WARNING
When the engine is running, exhaust gases can enter the vehicle interior if the lift gate is open.
There is a risk of poisoning
Close the lift gate.
The hood is open.
A warning tone also sounds.
WARNING
The open hood may then block your view when the vehicle is in motion.
There is a risk of an accident.
1. Pull over and stop the vehicle safely as soon as possible, paying attention to road and traffic conditions.
2. Secure the vehicle against rolling away.
3. Close the hood.
At least one door is open. A warning tone also sounds.
Close all doors.
[Power Steering Malfunc-
tion See Operator's
Manual]The power steering assistance is faulty.
A warning tone also sounds.WARNING
You will need to use more force to steer.
There is a risk of an accident.
1. Check whether you are able to apply the extra force required.
2. If you are able to steer safely: carefully drive on to a qualified specialist workshop.
3. If you are unable to steer safely: do not drive on. It is recommended you contact the nearest INFINITI retailer.
2-56Instruments and controls

IMMOBILISER
The immobiliser prevents your vehicle from
being started without the correct key.
•To activate with the key: remove the key
from the ignition lock.
•To deactivate:switch on the ignition.
When leaving the vehicle, always take the key
with you and lock the vehicle. Anyone can
start the engine if a valid key has been left
inside the vehicle.
NOTE
The immobiliser is always deactivated when
you start the engine.
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this de-
vice must accept any interference received,
including interference that may cause unde-
sired operation.NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compli-
ance could void the user’s authority to oper-
ate the equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause unde-
sired operation of the device.
ANTI-THEFT ALARM SYSTEM
(IF EQUIPPED)
To arm:lock the vehicle with the key or Intel-
ligent Key. Indicator light
1flashes. The
alarm system is armed after approximately
15 seconds.
To deactivate:unlock the vehicle with the key
or Intelligent Key.
or
Insert the key into the ignition switch.
A visual and audible alarm is triggered if the
alarm system is armed and you open:
•A door.
•The vehicle with the emergency key element.
•The lift gate.
•The hood.
NIC2750
SECURITY SYSTEM
2-60Instruments and controls

When indicator light1lights up green:
programing is finished.
When indicator light
1flashes green:
programing was successful. The next step
is to synchronize the rolling code.
6. Release button
6of the hand held trans-
mitter
5for the garage door drive.
If indicator light
1lights up red: repeat
the programing process for the corre-
sponding button on the rear-view mirror.
When doing so, vary the distance be-
tween the hand held transmitter
5and
the rear-view mirror.
The required distance between the hand
held transmitter
5and the HomeLink®
depends on the garage door drive system.
Several attempts might be necessary. You
should test every position for at least
25 seconds before trying another posi-
tion.
PROGRAMMING TROUBLE
DIAGNOSIS
If the HomeLink® does not quickly learn the
hand-held transmitter information:
•Check the transmitter frequency used by
garage door drive hand-held transmitter
5and whether it is supported. The trans-
mitter frequency can usually be found onthe back of the garage door drive hand-
held transmitter. HomeLink® is compat-
ible with devices that have units which
operate in the frequency range of 280 to
433 MHz.
•Replace the hand-held transmitter5bat-
teries with new batteries.
This increases the likelihood that the hand-
held transmitter
5will transmit a strong
and precise signal to the HomeLink®.
•When programing, hold the hand-held
transmitter
5at varying distances and
angles from the button which you are pro-
graming. Try various angles at a distance
between 2 and 12 inches (5 to 30 cm) or at
the same angle but at varying distances.
•If another hand-held transmitter is avail-
able for the same garage door drive, re-
peat the same programing steps with this
hand-held transmitter
5. Before per-
forming these steps, make sure that new
batteries have been installed in the hand-
held transmitter
5.
•Note that some hand-held transmitters
only transmit for a limited amount of time
(the indicator light on the hand-held trans-
mitter goes out). Press button
6on re-
mote hand-held transmitter
5again be-
fore transmission ends.
•Align the antenna cable of the garage door
opener unit. This can improve signal
reception/ transmission.
If you have any questions or are having diffi-
culty programming your HomeLink® but-
tons, refer to the HomeLink® web site at:
www.homelink.com or 1-800-355-3515.
OPERATING THE HOMELINK®
UNIVERSAL TRANSCEIVER
The HomeLink® Universal Transceiver, after
it is programmed, can be used to activate the
programmed device.
1. Turn the ignition key to the ON position.
2. Press button
2,3or4which you have
programed to operate the garage door.
Garage door system with a fixed code:
indicator light
1lights up green
Garage door system with a rolling code:
indicator light
1flashes green.
The transmitter will transmit a signal as long
as the button is pressed. The transmission is
halted after a maximum of ten seconds and
indicator light
1lights up yellow. Press but-
ton
2,3or4again if necessary.
For convenience, the hand-held transmitter
of the device may also be used at any time.
2-92Instruments and controls

3 Pre-driving checks and adjustments
Keys..............................3-2
INFINITI Intelligent key................3-2
INFINITI Vehicle immobilizer system keys.....3-3
Doors.............................3-4
Locking with the key..................3-4
Locking with the mechanical key..........3-5
Locking with inside door knob............3-6
Locking with Power door lock switch.......3-6
Automatic door locks.................3-7
Child safety rear door lock..............3-7
Lift gate lock.......................3-7
INFINITI Intelligent Key system.............3-8
Operating range.....................3-9
Door locks/unlocks precaution..........3-10
INFINITI Intelligent Key operation........3-10Changing the settings of the locking system . .3-11
Troubleshooting guide................3-12
Hood.............................3-15
Fuel-filler door.......................3-16
Opening fuel-filler door...............3-16
Fuel-filler cap......................3-16
Steering wheel.......................3-17
Sun visors..........................3-18
Vanity mirror......................3-18
Mirrors............................3-18
Automatic anti-glare rear view mirror......3-18
Outside mirrors....................3-18
Memory function (if equipped).............3-21
Storing settings....................3-22
Calling up a stored setting.............3-22

4. Insert the support rod3into the slot4on the underside of the hood.
5. When closing the hood, replace the sup-
port rod in its original position
5, slowly
lower the hood to about8–12in.(20–
30 cm) above the hood lock, then let it
drop. Make sure the hood is securely
latched.
WARNING
•Make sure the hood is completely closed
and latched before driving. Failure to do
so could cause the hood to fly open and
result in an accident.
•If you see steam or smoke coming from
the engine compartment, to avoid injury
do not open the hood.
OPENING FUEL-FILLER DOOR
To open the fuel-filler door, unlock it using
one of the following operations, then push
the right side of the door
1.
•Push the door handle request switch with
the Intelligent Key carried with you.
•Push the “UNLOCK”button on the
Intelligent Key.
•Push the power door lock switch to the
“UNLOCK”position.
To close the fuel-filler door, close the door
until it securely latches. To lock the fuel filler
door, lock the vehicle using the intelligent key.
FUEL-FILLER CAP
Turn the fuel-filler cap counterclockwise to
remove. To tighten, turn the cap clockwise
until a single click is heard.
Put the fuel-filler cap on the cap holder
2while refueling.
WARNING
•Gasoline is extremely flammable and
highly explosive under certain condi-
tions. You could be burned or seriously
injured if it is misused or mishandled.
Always stop the engine and do not
smoke or allow open flames or sparks
near the vehicle when refueling.
•Do not attempt to top off the fuel tank
after the fuel pump nozzle shuts off au-
tomatically. Continued refueling may
cause fuel overflow, resulting in fuel
spray and possibly a fire.
•Use only an original equipment type
fuel-filler cap as a replacement. It has a
built-in safety valve needed for proper
operation of the fuel system and emis-
sion control system. An incorrect cap
can result in a serious malfunction and
possible injury.
NDI1605NPA1482
FUEL-FILLER DOOR
3-16Pre-driving checks and adjustments