400
Features
HomeLink® Universal Transceiver*
The HomeLink ® Universal Transceiver can be pr ogrammed to operate up to three 
remote controlled devices around your home, such as garage doors, lighting, or 
home security systems.
Refer to the safety information that came wi th your garage door opener to test that 
the safety features are functioning properly. If you do not have the safety 
information, contact the manufacturer.
Before programming HomeLink, make sure that people and objects are out of the 
way of the garage or gate to prevent potential injury or damage.
When programming a garage door opener, park  just outside the garage door’s path.
■Important Safety Precautions
1HomeLink ® Universal Transceiver*
Before programming HomeLi nk to operate a garage 
door opener, confirm that the opener has an external 
entrapment protection system, such as an “electronic 
eye,” or other safety and reverse stop features. If it 
does not, HomeLink may not  be able to operate it.
* Not available on all models 
uuHomeLink ® Universal Transceiver*u Training HomeLink
402
Features
■Programming a Button1Training HomeLink
Reprogramming a Button
If you want to retrain  a programmed button for a 
new device, you do not ha ve to erase all button 
memory. You can replace the existing memory code 
using this procedure:
Erasing Button Memory
To erase programming from the buttons, press and hold 
the two outside HomeLink buttons until the HomeLink 
indicator changes from 
orange to rapidly flashing green. 
This should take about 10 seconds. You should erase all 
programming before selling the vehicle.
Operating
To operate, simple pr ess and release the 
programmed HomeLink butto n. Activation will now 
occur for the trained device.
Questions
For questions or  comments, visit 
www.HomeLink.com , www.youtube.com/
HomeLinkGentex , or by calling the HomeLink Hotline 
(North America only) at (800) 355-3515.
HomeLink®  is a registered tra demark of Gentex 
Corporation.
2.
1. Press and hold the desired HomeLink button until 
the HomeLink indi
cator begins to slowly flash 
orange . This should take about 20 seconds.
Release the HomeLink  button and position the 
remote transmitter you wish to link 1 - 3 inches 
(3 - 8 cm) from the HomeLink button you want to 
program, then follow steps 3 - 6 under 
“programming a button.”
Training 
CompleteHomeLink LED is 
continuously on green .
YES
YES
1.Position the remote transmitter you wish to link 1 to 3 inches (3 - 8 cm) from the 
HomeLink®  button you want to program.
3b.
Canadian Garage Door Opener
A. Press and release the HomeLink 
button. Press, hold and release the 
button on the remote every 2 secs. 
Does the HomeLink indicator (LED) 
change from  slowly flashing orange to 
rapidly flashing or continuously on 
green ? The process should take less 
than 60 seconds.
NO
2. Press and release the desired HomeLink but ton. Is the HomeLink indicator (LED) slowly 
flashing orange ? 
NO
3a.Hold the button on the remote 
transmitter. Does HomeLink indicator 
(LED) change from  slowly flashing 
orange to rapidly flashing green or 
continuously on green ? The process 
should take less than 60 seconds.
5. Press and hold the HomeLink button again.
HomeLink indicator  rapidly flashes 
green .
5a.The remote has a rolling code. Press the 
“learn” button on the remote-controlled 
device (e.g. garage door opener).6.Press and hold the HomeLink button 
again.
The remote-controll ed device should 
operate.
Training Complete
5b.Within 30 secs, press and hold the 
programmed HomeLink button for 2 
secs.
4.Press and hold the programmed HomeLink 
button for about a second. Does the device 
(garage door opener) work?