2019 HONDA ACCORD HYBRID battery

465Continued
Driving
When DrivingStarting the Engine 1. Make sure the parkin g brake is applied.
u The parking brake indicator (red) comes
on for 30 seconds when you pull up the
electric parking brake switch.
u The parking brake must be applied to
start the engine.
2. Depress the brake pedal.
u Although it is possible to start the vehicle
in ( N
with the parking brake applied, it is
safer to start it in ( P
.
3. Press the ENGINE START/STOP button
without depressing the accelerator pedal. 1 Starting the Engine
Keep your foot firmly on the brake pedal when
starting the engine.
The engine is harder to st art in cold weather and in
thinner air found at altitudes above 8,000 feet (2,400
meters).
When starting the engine in cold weather, turn off all
electrical accessories such as the lights, climate
control system and rear de fogger in order to reduce
battery drain.
If you live in a region where winter is extremely cold,
an engine block heater will improve starting and
warming of the engine. Cons ult a dealer for details.
If the exhaust system sounds abnormal or you can
smell exhaust gas inside the vehicle, have your vehicle
checked by a dealer. There may be a problem with
the engine or exhaust system.
The immobilizer system pr otects your vehicle from
theft.
If an improperly c oded device is used, the engine’s
fuel system is disabled.
2 Immobilizer System P. 183Automatic transmission models
Electric Parking Brake Switch
Brake Pedal

uu When Driving u Starting the Engine
466
Driving 1. Make sure the parking brake is applied.
u The parking brake indicator (red) comes
on for 30 seconds when you pull up the
electric parking brake switch.
u The parking brake must be applied to
start the engine.
2. Check that the tr ansmission is in ( P
, then
depress the brake pedal.
u Although it is possible to start the vehicle
in ( N
with the parking brake applied, it is
safer to start it in ( P
.
3. Press the ENGINE START/STOP button
without depressing the accelerator pedal.Continuously variable transmission models
Electric Parking Brake Switch 1 Starting the Engine
Bring the remote close to the ENGINE START/STOP
button if the battery in the remote is weak.
2 If the Remote Battery is Weak P. 672
The engine may not start if the remote is subjected to
strong radio waves.
Do not hold the ENGINE START/STOP button to
start the engine.
If the engine does not start, wait at least 30 seconds
before trying again.
Brake Pedal

uu When Driving u Starting the Engine
470
Driving ■ To stop the engine 1 Remote Engine Start with Vehicle Feedback *
• You have already used the remote twice to start
the engine.
• Another registered remo te is in the vehicle.
• There is an antenna failure.
• The door is unlocked with the built-in key.
• The engine oil pressure is low.
• The engine coolant temper ature is extremely high.
• The security system alarm is not set.
The engine may stop whil e it is running if:
• You do not start the vehicl e within 10 minutes of
starting the engine with the remote.
• The engine is stopped by using the remote.
• The security system alarm is activated.
• The door is unlocked with the built-in key.
• The hood is open.
• The engine coolant temper ature is extremely high.
• The battery is low.
• The engine oil pressure is low.
• The malfunction indicator lamp (MIL) comes on if
there is a problem with the emissions control
systems.
• You press the ENGINE START/STOP button
without depressing the brake pedal.
• The transmission is in a position other than ( P
.
• You press the shift lever release button. Automatic transmission models
Continuously variable transmission modelsPress and hold the
button for one second. Go within the range,
and try again.
The exterior lights flash once if the engine stops successfully.The exterior lights will not flash when the remote is out of
the smart entry system range.
The engine will not stop.
* Not available on all models

494 uu When Driving u Vehicle Stability Assist ® (VSA ® ), aka Electronic Stability Control (ESC), System
Driving Vehicle Stability Assist ® (VSA ® ), aka Electronic
Stability Control (ESC), System VSA ® helps to stabilize the vehicle during cornering if the vehicle turns more or less
than what was intended. It also assists in maintaining traction on slippery surfaces.
It does so by regulating engine output and select ively applying the brakes.
When VSA ® activates, you may notice that the
engine does not respond to the accelerator.
You may also notice some noise from the
hydraulic system. You will also see the
indicator blink.
■ VSA ® Operation 1 Vehicle Stability Assist ® (VSA ® ), aka Electronic Stability Control
(ESC), System
The VSA ® may not function properl y if tire type and
size are mixed. Make sure to use the same size and
type of tire, and the air pressures as specified.
When the VSA ® system indicator comes on and stays
on while driving, there ma y be a problem with the
system. While this may not interfere with normal
driving, have your vehi cle checked by a dealer
immediately.
VSA ® cannot enhance stability in all driving situations
and does not control the entire braking system. You
still need to drive and corner at speeds appropriate
for the conditions and always leave a sufficient
margin of safety.
The main function of the VSA ® system is generally
known as Electronic Stability Control (ESC). The
system also includes a traction control function.
The Vehicle Stability Assist ® (VSA ® ) system, Vehicle
Stability Assist ® (VSA ® ) OFF, adaptive cruise control
(ACC) with low speed follow (LSF) *
, adaptive cruise
control (ACC) *
, safety support and low tire pressure/
TPMS indicators may come on in amber along with a
message in the driver information interface when you
set the power mode to ON after re-connecting a
battery.
Drive a short distance at more than 12 mph (20 km/h).
Each indicator should go of f. If any do not, have your
vehicle checked by a dealer.VSA ® System
Indicator
* Not available on all models

uu When Driving u Tire Pressure Monitoring System (TPMS)
498
Driving You can calibrate the system from the
customized feature on the audio/information
screen. 2 Audio System Basic Operation P. 252
1. Set the power mode to ON.
2. Press the MENU/CLOCK button.
3. Rotate to select Settings , then press
.
4. Rotate to select Vehicle Settings , then
press .
5. Rotate to select TPMS Calibration ,
then press .
6. Rotate to select Calibrate , then press
.
• If the Calibration failed to start. message
appears, repeat steps 5-6.
• The calibration pr ocess finishes
automatically. 1 Tire Pressure Monitoring System (TPMS)
The low tire pressure/TPMS indicator may come on
under the following conditions:
• A compact spare tire is used.
• There is a heavier and une ven load on the tires,
such as when towing a trailer *
, than the condition
at calibration.
• Snow chains *
are used.
The Vehicle Stability Assist ® (VSA ® ) system, Vehicle
Stability Assist ® (VSA ® ) OFF, adaptive cruise control
(ACC) with low speed follow (LSF) *
, adaptive cruise
control (ACC) *
, safety support and low tire pressure/
TPMS indicators may come on in amber along with a
message in the driver info rmation interface when you
set the power mode to ON after re-connecting a
battery.
Drive a short distance at mo re than 12 mph (20 km/h).
Each indicator should go off. If any do not, have your
vehicle checked by a dealer.
1 TPMS Calibration
TPMS cannot be calib rated if a compact spare tire is
installed.
The calibration process requires approximately 30
minutes of cumulative driv ing at speeds between 30-
60 mph (48-97 km/h).
During this period, if the pow er mode is set to ON and
the vehicle is not moved wi thin 45 seconds, you may
notice the low tire pressu re/TPMS indicator comes on
briefly. This is normal and indicates that the calibration
process is not yet complete.Models with color audio
* Not available on all models

Continued
513uu Honda Sensing ® u Collision Mitigation Braking System TM
(CMBS TM
)
Driving
When you turn the CMBS TM
on and off, do the
following.
1. Press the safety support switch.
2. Roll the left selector wheel to the
symbol and push it.
u The message appears on the driver
information interface when the system
becomes on or off.
The CMBS TM
is turned on every time you start
the engine, even if you turned it off the last
time you drove the vehicle.■ CMBS TM
On and Off 1 Collision Mitigation Braking System TM
(CMBS TM
)
The CMBS TM
may automatically shut off, and the
safety support indicator (amb er) will come and stay
on under certain conditions:
2 CMBS TM
Conditions and Limitations P. 514
When the CMBS TM
is activated, it will continue to
operate even if the accele rator pedal is partially
depressed. However, it w ill be canceled if the
accelerator pedal is deeply depressed.
The Vehicle Stability Assist ® (VSA ® ) system, Vehicle
Stability Assist ® (VSA ® ) OFF, adaptive cruise control
(ACC) with low speed follow (LSF) *
, adaptive cruise
control (ACC) *
, safety support and low tire pressure/
TPMS indicators may come on in amber along with a
message in the driver information interface when you
set the power mode to ON after re-connecting a
battery.
Drive a short distance at mo re than 12 mph (20 km/h).
Each indicator should go of f. If any do not, have your
vehicle checked by a dealer.Left Selector Wheel
Safety Support Switch
* Not available on all models

Continued
521uu Honda Sensing ® u Adaptive Cruise Control (ACC) with Low Speed Follow (LSF) *
Driving
When driving at about 25 mph (40 km/h) or above: Take your foot off the
pedal and press the SET / – button when you reach th e desired speed. The moment
you release the button, th e set speed is fixed, and ACC with LSF begins.
When driving slower than about 25 mph (40 km/h): If the vehicle is moving
and the brake pedal is not depressed, pressing the button fixes the set speed to
about 25 mph (40 km/h) regardless of current vehicle speed. If the vehicle is
stationary, you can set the vehicle speed even with the brake pedal depressed.
When ACC with LSF starts operating, the
vehicle icon, interval bars and set speed
appear on the driver information interface.
When you use ACC with LSF, Straight Driving
Assist (a feature of the Electric Power Steering
system) is activated.
By enabling the steering system to
automatically compensate for natural steering
pull, Straight Driving Assist makes it easier for
you to keep your vehicle in a straight line.■ To Set the Vehicle Speed 1 To Set the Vehicle Speed
You can switch the displayed set speed
measurements on the driver information interface or
audio/information screen between mph and km/h.
2 Speed Unit P. 149
2 Customized Features P. 370, 381
The Vehicle Stability Assist ® (VSA ® ) system, Vehicle
Stability Assist ® (VSA ® ) OFF, adaptive cruise control
(ACC) with low speed follow (LSF), safety support
and low tire pressure/TPM S indicators may come on
in amber along with a message in the driver
information interface when you set the power mode
to ON after re-connecting a battery.
Drive a short distance at mo re than 12 mph (20 km/h).
Each indicator should go of f. If any do not, have your
vehicle checked by a dealer.On when ACC with LSF
begins
Press and release SET / − button
Set Vehicle SpeedSet Vehicle Interval

Continued
537uu Honda Sensing ® u Adaptive Cruise Control (ACC) *
Driving
Take your foot off the pedal and press down the SET / – button when you reach the
desired speed. The moment you release the button, the set speed is fixed, and ACC
begins.
When ACC starts operating, the vehicle icon,
interval bars and set speed appear on the
driver information interface.
When you use ACC, Straight Driving Assist (a
feature of the Electric Power Steering system)
is activated.
By enabling the steering system to
automatically compensate for natural steering
pull, Straight Driving Assist makes it easier for
you to keep your vehicle in a straight line.■ To Set the Vehicle Speed 1 To Set the Vehicle Speed
You can switch the displayed set speed
measurements on the driver information interface or
audio/information screen between mph and km/h.
2 Speed Unit P. 149
2 Customized Features P. 381
The Vehicle Stability Assist ® (VSA ® ) system, Vehicle
Stability Assist ® (VSA ® ) OFF, adaptive cruise control
(ACC), safety support and low tire pressure/TPMS
indicators may come on in amber along with a
message in the driver information interface when you
set the power mode to ON after re-connecting a
battery.
Drive a short distance at mo re than 12 mph (20 km/h).
Each indicator should go of f. If any do not, have your
vehicle checked by a dealer.On when ACC begins
Press and release SET / − Button
Set Vehicle SpeedSet Vehicle Interval