2019 GMC TERRAIN turn signal

2
Turn Signal Lever/IntelliBeam ButtonF
Driver Information Center
Steering Wheel Adjustment Lever
Audio Next-Previous Favorite Station Controls (behind steering wheel)
Windshield Wipers Lever
Engine Start-Stop ButtonCruise Control/Forward Collision AlertF/Heated Steering WheelF Buttons
Power Mirror/Window Controls
Power Liftgate ControlF
INSTRUMENT PANEL
Audio Volume Controls (behind steering wheel)
Driver Information Center Controls/Voice Recognition Buttons
Memory Seat ButtonsF
Exterior-Interior Lamp Controls/Electric Parking Brake Switch
Check Engine
Engine Oil Pressure
Lane Keep Assist Warning
Airbag Readiness
Cruise Control Set
Service Electric Parking Brake
Traction Control/StabiliTrak Active
Charging System
Security
Seat Belt Reminder
Brake System Warning
Electric Parking Brake
IntelliBeam Lighting
Symbols

4
The Keyless Access System enables operation of the doors, ignition and liftgate without removing the Remote Keyless Entry transmitter from your pocket or purse . The transmitter must be within 3 feet of the door being unlocked or within 3 feet of the liftgate.
KEYLESS UNLOCKING
With the transmitter within range:
Press the lock button on the driver’s door handle to unlock the driver’s door; press it again within 5 seconds to unlock all doors .
Press the lock button on a passenger door handle to unlock all doors .
Press the touchpad on the liftgate handle to open the liftgate .
KEYLESS LOCKING
With the ignition off, the transmitter removed from the vehicle, and all doors closed:
Press the lock button on any door handle to lock all doors immediately .
If Passive Locking is turned on, all doors will lock automatically after a short delay .
Note: To change the keyless locking and unlocking settings, go to Settings > Vehicle > Remote Lock, Unlock, Start.
Lock
Press to lock all doors .
Unlock
Press to unlock the driver’s door . Press again to unlock all doors .
Power LiftgateF
Press twice to open or close the liftgate . Press once to stop power liftgate operation .
Vehicle Locator/Panic Alarm
Press and release to locate your vehicle . The exterior lamps will flash and the horn will sound .
Press and hold to activate the alarm . Press again to cancel the alarm .
Note: To change the remote settings, go to Settings > Vehicle > Remote Lock, Unlock, Start.
Remote Vehicle StartF
Press and release the Lock button and then immediately press and hold the but-ton until the turn signal lamps flash to start the engine from outside the vehicle . After entering the vehicle, turn on the ignition .
• During a remote start, the engine will run for 15 minutes . Repeat these steps to run the engine for an additional 15 minutes . A remote start can be extended once .
• Press and hold the button until the parking lamps turn off to cancel a remote start .
Remote Start Auto Heated/Ventilated SeatsF:
Select the Remote Start Auto Heat Seats or Remote Start Auto Cool Seats option in the Vehicle Settings to have the heated or ventilated seats turn on during a remote start . The seat button indicators do not illu-minate and the temperature performance of the unoccupied seats may be reduced during a remote start .
KEYLESS ACCESS SYSTEM
See Keys, Doors and Windows in your Owner’s Manual .F Optional equipment
REMOTE KEYLESS ENTRY TRANSMITTER
See Keys, Doors and Windows in your Owner’s Manual .

9
LIGHTING
UNIVERSAL REMOTE SYSTEMF
EXTERIOR LAMP CONTROL
Rotate the knob on the left side of the instru-ment panel to activate the exterior lamps .
Off/On
AUTO
Automatically activates the Daytime Running Lamps (DRLs) or the headlamps and other exterior lamps depending on outside light conditions .
Parking Lamps
Headlamps
Fog LampsF
Press the button to turn the fog lamps on or off.
INSTRUMENT PANEL LIGHTING
Instrument Panel Illumination
Press and release the knob to extend it . Turn the knob to adjust the instrument panel lighting .
INTELLIBEAM SYSTEMF
The IntelliBeam system automatically turns the high-beam headlamps on/off based on traffic conditions . A green indicator displays on the instrument cluster when the system is on; a blue indicator displays when the high-beam headlamps are on .
Press the button on the turn signal lever with the exterior lamp control in the AUTO or Headlamps position to turn the IntelliBeam system on or off.
Note: IntelliBeam activates the high-beam headlamps only when driving over 25 mph. The IntelliBeam system is turned off if the fog lamps are on.See Lighting in your Owner’s Manual .
F Optional equipment
The Universal Remote System on the overhead console enables your vehicle to control 3 dif-ferent devices, ranging from garage doors and gates to home lighting . Go to www.homelink.com for detailed
videos and instructions on how to program the Universal Remote System . For additional
assistance, call 1-800-355-3515 .
See Instruments and Controls in your Owner’s Manual .

16
Safety or driver assistance features are no substitute for the driver’s responsibility to operate the vehicle in a safe manner. The driver should remain attentive to traffic, surroundings and road conditions at all times. Read your Owner’s Manual for important feature limitations and information.
SAFET Y ALERT SEATF – The driver’s seat pulses — left side, right side or simultaneously — to alert the driver of the direction of potential hazards .
Audible alerts or seat pulsing alerts may be selected . To change the alert settings, go to Settings > Vehicle > Collision/Detection Systems > Alert Type .
L ANE CHANGE ALERT WITH SIDE BLIND ZONE ALERTF – While driving, the system displays a warning symbol on the left or right side mirror when a vehicle is detected in that side blind zone area or rapidly approaching that area. The warning symbol flashes if a turn signal is activated when a vehicle has been detected on the same side .
To turn on or off, go to Settings > Vehicle > Collision/Detection Systems > Lane Change Alert .
FORWARD COLLISION ALERTF – The Vehicle Ahead Indicator is green when a vehicle is detected and is amber when following a vehicle ahead much too closely . When approaching a vehicle directly ahead too rapidly, a red alert flashes on the windshield and the Safety Alert Seat pulses or rapid beeps sound (if selected) .
Press the Collision Alert button on the steering wheel to set the alert timing to Far, Medium, or Near . This is also the Adaptive Cruise ControlF following gap setting .
FOLLOWING DISTANCE INDICATORF – The following distance to the vehicle ahead is indicated in seconds under the Info menu on the Driver Information Center . If no vehicle is detected ahead, dashes are displayed .
FORWARD AUTOMATIC BRAKINGF – In potential front-end imminent collision situations with detected vehicles, the brakes may be applied, if you haven’t already done so, to help reduce damage or avoid collisions at very low speeds with vehicles directly ahead .
To set Forward Automatic Braking and Forward Collision Alert to Alert and Brake, Alert, or Off, go to Settings > Vehicle > Collision/Detection Systems > Forward Collision System.
L ANE KEEP ASSIST WITH L ANE DEPARTURE WARNINGF – The system may help you avoid collisions due to unintentional lane departures . The Lane Keep Assist Indicator is green if the system is available to assist . If the vehicle approaches a detected lane marking without using a turn signal in that direction, the system may assist by gently turning the steering wheel and displaying an amber .
If active driver steering is not detected, the amber may flash and the Safety Alert Seat may pulse or beeps may sound (if selected) on the side of the departure direction as the lane marking is crossed . The Lane Keep Assist system does not continuously steer the vehicle; the driver needs to steer and be in complete control of the vehicle .
To turn on or off, press the Lane Keep Assist button on the center console .
FRONT PEDESTRIAN BRAKINGF – During daytime driving, the system detects pedestrians directly ahead up to a distance of approximately 131 ft . and displays an amber indicator . When approaching a detected pedestrian too quickly, a red alert flashes on the windshield and the Safety Alert Seat pulses or rapid beeps sound (if selected) . The system may prepare the brakes or automatically brake the vehicle .
To set to Alert and Brake, Alert, or Off, go to Settings > Vehicle > Collision/Detection Systems > Front Pedestrian Detection .
F Optional equipment
DRIVER ASSISTANCE SYSTEMS