2019 GMC TERRAIN mirror

2
Turn Signal Lever/IntelliBeam ButtonF
Driver Information Center
Steering Wheel Adjustment Lever
Audio Next-Previous Favorite Station Controls (behind steering wheel)
Windshield Wipers Lever
Engine Start-Stop ButtonCruise Control/Forward Collision AlertF/Heated Steering WheelF Buttons
Power Mirror/Window Controls
Power Liftgate ControlF
INSTRUMENT PANEL
Audio Volume Controls (behind steering wheel)
Driver Information Center Controls/Voice Recognition Buttons
Memory Seat ButtonsF
Exterior-Interior Lamp Controls/Electric Parking Brake Switch
Check Engine
Engine Oil Pressure
Lane Keep Assist Warning
Airbag Readiness
Cruise Control Set
Service Electric Parking Brake
Traction Control/StabiliTrak Active
Charging System
Security
Seat Belt Reminder
Brake System Warning
Electric Parking Brake
IntelliBeam Lighting
Symbols

7
STEERING WHEEL ADJUSTMENT
FRONT SEATS
F Optional equipment
With the vehicle parked, push down the lever under the steering column to adjust the steering wheel . The steering wheel can be moved up or down and in or out . Pull up the lever to lock the steering wheel in place .
See Instruments and Controls in your Owner’s Manual .
POWER SEAT ADJUSTMENTSF
A. Seat Adjustment
Move the horizontal control to move the seat forward or rearward and to tilt, raise or lower the seat .
B. Seatback Recline Adjustment
Move the top of the vertical control to recline or raise the seatback .
C. Lumbar Support Adjustment
Press and hold the rear control to adjust the lumbar support .
SET MEMORY SEAT POSITIONSF
With the ignition On or in Accessory mode:
1 . Adjust the seat and power outside mirrors to the desired positions .
2 . Press and release the SET button on the driver’s door . A beep will sound .
3 . Immediately press and hold button 1 or 2 until two beeps sound .
To store a seat position for when exiting the vehicle, repeat these steps using the Exit button .
RECALL MEMORY SEAT POSITIONSF
Press and hold button 1, 2 or Exit until the seat and mirrors reach the set position .
The memory/exit positions can be pro-grammed to be recalled automatically .
To set Seat Entry Memory and Seat Exit Memory, go to Settings > Vehicle > Seating Position .
FOLD-FLAT FRONT PASSENGER
SEATBACK
1 . Lower the head restraint and move the seat as far back as possible .
2 . Lift the recline lever (D) and fold the seatback forward .
To raise the seatback, lift the recline lever and fully raise the seatback .
See Seats and Restraints in your Owner’s Manual .
BAC
D

10
CLIMATE CONTROLS
F Optional equipment
Fan Speed Control or Driver’s Temperature ControlF
A/C Air Conditioning Control Vent Mode
Fan Speed Control/Power On-OffF
AUTO Automatic OperationF
Recirculation Mode
Rear Window Defog/Heated Outside Mirrors Control
Floor Mode Bi-level Mode
SYNCF Link passenger’s temperature setting to driver’s temperature setting
Defrost Mode
Passenger’s Temperature ControlF Defog Mode
AUTOMATIC OPERATIONF
Press AUTO .
Set the temperature .
The system automatically controls the fan speed, air delivery, air conditioning and
recirculation functions to maintain the set temperature . Allow time for the system to reach the desired temperature . If the functions are manually adjusted, full automatic operation is canceled .
AUTO DEFOGF AND AUTO REAR WINDOW DEFOGF
Auto Defog and Auto Rear Defog automatically turn on when the engine is started .
Go to Settings > Vehicle > Climate and Air Quality to turn the Auto Defog and Auto Rear Defog settings on or off.
See Climate Controls in your Owner’s Manual .
Dual Automatic Climate ControlsF shown

16
Safety or driver assistance features are no substitute for the driver’s responsibility to operate the vehicle in a safe manner. The driver should remain attentive to traffic, surroundings and road conditions at all times. Read your Owner’s Manual for important feature limitations and information.
SAFET Y ALERT SEATF – The driver’s seat pulses — left side, right side or simultaneously — to alert the driver of the direction of potential hazards .
Audible alerts or seat pulsing alerts may be selected . To change the alert settings, go to Settings > Vehicle > Collision/Detection Systems > Alert Type .
L ANE CHANGE ALERT WITH SIDE BLIND ZONE ALERTF – While driving, the system displays a warning symbol on the left or right side mirror when a vehicle is detected in that side blind zone area or rapidly approaching that area. The warning symbol flashes if a turn signal is activated when a vehicle has been detected on the same side .
To turn on or off, go to Settings > Vehicle > Collision/Detection Systems > Lane Change Alert .
FORWARD COLLISION ALERTF – The Vehicle Ahead Indicator is green when a vehicle is detected and is amber when following a vehicle ahead much too closely . When approaching a vehicle directly ahead too rapidly, a red alert flashes on the windshield and the Safety Alert Seat pulses or rapid beeps sound (if selected) .
Press the Collision Alert button on the steering wheel to set the alert timing to Far, Medium, or Near . This is also the Adaptive Cruise ControlF following gap setting .
FOLLOWING DISTANCE INDICATORF – The following distance to the vehicle ahead is indicated in seconds under the Info menu on the Driver Information Center . If no vehicle is detected ahead, dashes are displayed .
FORWARD AUTOMATIC BRAKINGF – In potential front-end imminent collision situations with detected vehicles, the brakes may be applied, if you haven’t already done so, to help reduce damage or avoid collisions at very low speeds with vehicles directly ahead .
To set Forward Automatic Braking and Forward Collision Alert to Alert and Brake, Alert, or Off, go to Settings > Vehicle > Collision/Detection Systems > Forward Collision System.
L ANE KEEP ASSIST WITH L ANE DEPARTURE WARNINGF – The system may help you avoid collisions due to unintentional lane departures . The Lane Keep Assist Indicator is green if the system is available to assist . If the vehicle approaches a detected lane marking without using a turn signal in that direction, the system may assist by gently turning the steering wheel and displaying an amber .
If active driver steering is not detected, the amber may flash and the Safety Alert Seat may pulse or beeps may sound (if selected) on the side of the departure direction as the lane marking is crossed . The Lane Keep Assist system does not continuously steer the vehicle; the driver needs to steer and be in complete control of the vehicle .
To turn on or off, press the Lane Keep Assist button on the center console .
FRONT PEDESTRIAN BRAKINGF – During daytime driving, the system detects pedestrians directly ahead up to a distance of approximately 131 ft . and displays an amber indicator . When approaching a detected pedestrian too quickly, a red alert flashes on the windshield and the Safety Alert Seat pulses or rapid beeps sound (if selected) . The system may prepare the brakes or automatically brake the vehicle .
To set to Alert and Brake, Alert, or Off, go to Settings > Vehicle > Collision/Detection Systems > Front Pedestrian Detection .
F Optional equipment
DRIVER ASSISTANCE SYSTEMS