2019 FIAT 500L warning

START&STOP SYSTEM
CONTROL
The dual zone automatic climate control
manages the Start&Stop system
(engine off and vehicle at a standstill) in
order to guarantee sufficient comfort
inside the passenger compartment.
IMPORTANT In particularly severe
climate conditions it is recommended to
limit the use of the Start&Stop system
to prevent the compressor from
continuously switching on and off, with
consequent rapid misting of the
windows and accumulation of humidity
with unpleasant smells in the passenger
compartment.
IMPORTANT When the Start&Stop
system is on (engine off and car at a
standstill), the automatic recirculation
management is turned off always taking
air in from outside, to reduce the
probability of the windows misting up
(as the compressor is off).
WARNING
19)It is inadvisable to use internal air
recirculation when the outside temperature
is low, since the windows could mist up
rapidly.
WARNING
5)The climate control system detects the
passenger compartment temperature
using a mean radiant temperature sensor
located in the interior rear view mirror
and protected by a specific cover.
Obstructing the field of view of this sensor
with any object could cause the climate
control system to operate with less than
optimal efficiency.
CLIMATE CONTROL
SYSTEM
The system uses a coolant that is
compatible with the laws in force in the
countries where the vehicle is sold,
R134a or R1234yf. When charging,
only use the gas indicated on the
dedicated plate in the engine
compartment fig. 26.
The use of other coolants affects the
efficiency and condition of the system.
The lubricant used for the compressor
is also strictly linked to the type of
cooling gas: contact a Fiat Dealership.
26F0Y0999C
24
KNOWING YOUR CAR

EXTERIOR LIGHTS
The external lights can only be
switched on when the ignition key is
turned to MAR.
DAYTIME RUNNING
LIGHTS (DRL)
(for versions/markets, where provided)
20) 21)
With the ignition key at MAR and ring
nut A fig. 27 turned toOthe daytime
running lights are activated
automatically; the other lights and
interior lighting remain off.SIDE LIGHTS / DIPPED
BEAM HEADLIGHTS
With the ignition key turned to MAR,
turn ring nut A to
. If dipped beam
headlights are activated, the daytime
running lights switch off and the side
lights and dipped headlights switch on.
The
warning light switches on in
the instrument panel.
When the ignition key is turned to
STOP or removed and the ring nut A is
turned fromOto
, all the side
lights and the number plate lights come
on. The
warning light switches
on in the instrument panel.
If the side lights are left on and the
driver side door is opened, a buzzer
sounds and the display shows a
message warning the driver that the car
is being left with the lights on. The
buzzer stops when the driver side door
is closed.
FOG LIGHTS / REAR FOG
LIGHT
The fog lights can be switched on at
any time.
If the fog lights are turned on with the
ring nut onO, the DRL (where provided)
will switch off and the front and rear
side lights will switch on.If the fog lights are turned on with the
ring nut on
and the dusk sensor
detecting daytime light conditions, the
DRL (where provided) will switch off and
the front and rear side lights will switch
on.
To turn on the front/rear fog lights,
press button fig. 28 as follows:
first pressing: front fog lights on;
second pressing: rear fog lights
and front fog lights (already activated by
first pressing) on;
third pressing: front fog lights off;
fourth pressing: rear fog lights and
front fog lights (already deactivated by
third pressing) off.
With front fog lights on, the
warning
light on the instrument panel will come
on. With rear fog lights on, the
warning light on the instrument
panel will come on at the same time.
28F0Y0648C
25
"’99;U;;W^’

If the front and rear fog lights are on
when the engine is stopped, they will
switch off. When the engine is
restarted, the fog lights will remain off
until switched on again by pressing the
button.
AUTOMATIC LIGHTING
CONTROL (AUTOLIGHT)
(dusk sensor)
(for versions/markets, where provided)
This is an infrared LED sensor located
on the windscreen, which detects
variations in outside light levels.
Activation: turn ring nut A fig. 27 to
.
With dusk sensor active, with daytime
running lights (DRL) on, it is not
possible to keep the main beam
headlights on constantly; only flashing
is permitted. In these conditions, the
main beam headlights can be turned on
by turning the ring nut to
and
pushing the stalk towards the
dashboard; otherwise, wait until the
dusk sensor indicates a low light level
(dipped beam headlights on).
On automatic sensor controlled
deactivation, the dipped beam
headlights are deactivated first,
followed by the side lights a few
seconds later.IMPORTANT The sensor cannot detect
the presence of fog. These lights must
therefore be switched on manually in
these circumstances.
MAIN BEAM HEADLIGHTS
With ring nut in position
, push the
stalk forward toward the dashboard
(stable position) to turn on the lights.
The
warning light on the instrument
panel turns on.
The lights are switched off by pulling
the stalk towards the steering wheel.
FLASHING
Pull the left stalk fig. 29 toward yourself,
to the stable position; the stalk goes
back to the central stable position when
it is released. With main beam
headlights on, the
warning light on
the instrument panel will come on at
the same time.DIRECTION INDICATORS
Place the lever in the (stable) position:
upwards:right-hand direction indicator
activation/downwards:left-hand
direction indicator activation.
The
orwarning light will blink on
the instrument panel.
The direction indicators are switched off
automatically when the steering wheel
is straightened.
"Lane change" function
If you wish to signal a lane change,
place the left stalk in the unstable
position for less than half a second. The
direction indicator on the side selected
will be activated for 5 flashes and
then go out automatically.
“Cornering lights”
When the dipped beam headlights are
on and the speed is below 40 km/h,
if the steering wheel rotation angle
is large or the direction indicators are
on, a light (incorporated in the fog light)
will come on on the relevant side to
improve visibility at night time.
COURTESY LIGHTS
The function can be enabled and its
times set use the "Settings" Menu
of theUconnect™system. When the
doors are unlocked, the side lights
and puddle lights come on for the time
set in the menu.
26
KNOWING YOUR CAR
")99;U;ZZY’

Once any door is opened, the lights
remain on for a further 180 seconds, or
for a further 10 seconds after the door
is closed.
"FOLLOW ME HOME"
DEVICE
This allows the space in front of the car
to be lit for a set time.
Activation
With the key turned to STOP or
removed, pull the left-hand stalk
towards the steering wheel within 2
minutes from when the engine is turned
off. Each time the stalk is operated,
the lights stay on for an extra 30
seconds up to a maximum of 210
seconds. When this time is up the lights
automatically switch off.
Each time the stalk is operated, the
warning light
on the instrument
panel switches on. The display shows a
message and the time set for the
function. The
warning light comes
on when the stalk is first operated
and stays on until the function is
automatically deactivated.Deactivation
Keep the stalk pulled towards the
steering wheel for more than 2
seconds.
WARNING
20)The daytime running lights are an
alternative to the dipped beam headlights
for driving during the daytime in countries
where it is compulsory to have lights on
during the day; where it is not compulsory,
the use of daytime running lights is
permitted.
21)Daytime running lights cannot replace
dipped beam headlights when driving at
night or through tunnels. The use of
daytime running lights is governed by the
Highway Code of the country in which you
are driving. Comply with legal
requirements.
INTERIOR LIGHTS
FRONT CEILING LIGHT
Switch A fig. 30 is used to switch on/off
the roof light bulbs.
Switch A positions:
central position: lights C and E
switch on/off when the doors are
opened/closed;
pressed to the left (position OFF):
lights C and E are always switched off;
pressed to the right (position):
lights C and D are always switched on.
The lights switch on/off progressively,
controlled by a timer, when the driver
enters and exits the car.
30F0Y0098C
27

WARNING
22)Make sure the device is switched off
whenever the windscreen must be
cleaned.
WARNING
6)Do not use the windscreen wiper to
remove layers of snow or ice from the
windscreen. In such conditions, the
windscreen wiper may be subjected to
excessive stress and the motor cut-out
switch, which prevents operation for a few
seconds, may intervene. If operation is
not restored (even after turning the key and
restarting the engine), contact a Fiat
Dealership.
7)Do not operate the windscreen wiper
with the blades lifted from the windscreen.
8)Do not activate the rain sensor when
washing the car in an automatic car wash.
9)Make sure the device is switched off if
there is ice on the windscreen.
10)Do not use the rear window wiper to
remove layers of snow or ice. In such
conditions, the screen wiper may be
subjected to excessive stress and the
motor cut-out switch, which prevents
operation for a few seconds, may
intervene. If operation is not restored,
contact a Fiat Dealership.
FIXED GLASS ROOF
(for versions/markets, where provided)
SUN BLIND
The sun blind operates only with the
ignition key turned to MAR. From the
fully closed position press button A fig.
33 for more than half a second: the
blind will move to the fully open
position.
From the fully open position press
button A for more than half a second:
the blind will move to the fully closed
position.
Button A can be pressed in jog mode
to open or close the blind manually.EMERGENCY OPERATION
If the control button does not work, to
move the sun blind manually, remove
the protective cap A fig. 34 on the
internal trim, take the Allen key B
provided (located in the tool box or,
depending on the version, in the
Fix&Go Automatic container in the
luggage compartment), insert it in
housing A and turn it clockwise to open
the blind or anticlockwise to close it.
SUN BLIND
INITIALISATION
Following an automatic movement
malfunction while opening/closing or
after an emergency manoeuvre (see
description in the previous paragraph),
the automatic operation of the sun
curtain must be initialised again.
33F0Y0121C34F0Y0285C
30
KNOWING YOUR CAR

take Allen key C fig. 36 from the tool
box or, depending on the version,
from the Fix&Go Automatic container,
insert it in housing A (for blind
movement) or B (for sun roof
movement) and turn it clockwise to
open the roof (or the blind) or
anticlockwise to close the roof (or the
blind).
SUN ROOF
INITIALISATION
Following an automatic movement
malfunction while opening/closing or
after an emergency manoeuvre (see
description in the previous paragraph),
the automatic operation of the sunroof
must be initialised again.
Proceed as follows
turn the ignition key from the STOP
position to the MAR position;
hold down button A fig. 35: after
approximately 10 seconds the roof
moves jerkily to closing position. When
the movement stops (closed roof),
release button A (if the roof is already
closed, you will hear the mechanical
lock only);
press button A again within 5
seconds after the blind reached the fully
closed position;
hold down button A: the roof will
perform an automatic opening and
closing cycle. Should this not occur,
repeat the operation from the
beginning;
hold down button A until the roof is
completely closed: the initialisation
procedure has ended.
WARNING
23)When leaving the vehicle, always
remove the key from the ignition to avoid
the risk of injury to those still inside the
vehicle due to accidental operation of the
sun roof. Improper use of the roof can
be dangerous. Before and during
operation, always check that no one is
exposed to the risk of being injured by the
moving sun roof or by objects getting
caught or hit by it.
WARNING
11)Do not open the sunroof if a transverse
roof rack is fitted. Do not open the sunroof
if there is snow or ice on it: you may
damage it.
36F0Y0234C
32
KNOWING YOUR CAR

To restore the starting condition of the
door locks (only if battery charge
restored) press the
button on the
remote control or the
button on the
dashboard or introduce the metal insert
of the ignition key in the driver's side
front door pawl and pull the door inner
handle.
INITIALISING THE DOOR
OPENING / CLOSING
MECHANISM
If the battery is disconnected or the
protection fuse blows, the door
opening/closing mechanism must be
initialised as follows:
close all the doors;
press thebutton on the remote
control or the button on the dashboard;
press thebutton on the remote
control or the button on the dashboard.
WARNING
24)Always use this device when carrying
children. After engaging the child lock
on both rear doors, check for effective
engagement by trying to open a door with
the internal handle.
WARNING
12)If the child lock was engaged and the
previously described locking procedure
carried out, operating the internal opening
handle will not open the door: in this case,
to open the door, the outside handle
must be used. The door central locking/
unlocking button
is not disabled by the
engagement of the emergency lock.
ELECTRIC WINDOWS
25)
OPERATION
These operate when the ignition key is
turned to MAR-ON and for about 3
minutes after the ignition key is turned
to STOP or removed unless one of
the front doors is opened.
DRIVE SIDE FRONT
DOOR CONTROLS
Versions with 4 electric windows
The buttons are located on the door
panel trim fig. 40.
All windows can be controlled from the
driver side door panel.
A: front left window opening/
closing. "Automatic continuous"
operation during window opening/
closing and anti-pinch system
activated.
39F0Y0110C
40F0Y0240C
34
KNOWING YOUR CAR

B: right front window opening/
closing. "Automatic continuous"
operation during window opening/
closing and anti-pinch system
activated.
C: enabling/disabling of rear door
electric window controls.
D: rear left window opening/closing
(for versions/markets, where provided).
"Automatic continuous" operation
during window opening/closing and
anti-pinch system activated.
E: rear right window opening/
closing (for versions/markets, where
provided). "Automatic continuous"
operation during window
opening/closing and anti-pinch system
activated.
Window opening
Push the buttons to open the desired
window. When one of the two buttons
is pressed briefly, the window moves
in "stages"; if the button is held down,
"continuous automatic" operation is
activated. If the button is pressed
again, the window will stop in
the desired position.Window closing
Lift the buttons to close the desired
window. The window closing stage
occurs following the same logic
described for the opening stage.
Anti-crush safety device
(for versions/markets, where provided)
The anti-pinch function is active both
during manual and automatic operation
of the electric windows. When the
anti-crush system is activated
the window travel is immediately
interrupted and then reversed. The
window cannot be operated in any way
during this time.
ELECTRIC WINDOWS
INITIALIZATION
If power supply is interrupted when the
window is moving, the electric window
automatic operation must be
reinitialised. The initialisation procedure
must be carried out with the doors
closed (and for each door) as follows:
fully close the window to be
initialised, with manual operation;
after the window has reached the
upper end of travel, hold the up button
pressed for at least one second.
WARNING
25)Improper use of the electric windows
can be dangerous. Before and during
operation, always check that passengers
are not exposed to the risk of being injured
either directly by the moving windows or
through objects getting caught or struck by
them. When leaving the vehicle, always
remove the ignition key to avoid the risk of
injury for people still on board due to
accidental operation of the electric
windows.
35