2019 DACIA LOGAN driving

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.23
ENG_UD32519_4
Dispositifs de correction et d’assistance à la conduite (X52 - Da\
cia)
ENG_NU_993-5_X52_Dacia_2
DRIVER CORRECTION DEVICES/AIDS (4/4)
Hill start assistance
This device assists the driver when
starting on hills (ascending or descend-
ing). It prevents the vehicle from rolling
forwards or backwards by automatically
applying the brakes when the driver lifts
their foot off the brake pedal to depress
the accelerator pedal.
System operation
It only operates when the gear lever is
in a position other than neutral (other
than N for sequential gearboxes) and
the vehicle is completely stationary
(brake pedal depressed).
The system holds the vehicle for ap-
proximately 2 seconds. The brakes are
then released (the vehicle will move ac-
cording to the slope).The hill start assistance
system cannot completely
prevent the vehicle from
rolling backwards in all sit-
uations (extremely steep gradients,
etc.).
In all cases, the driver may depress
the brake pedal to prevent the
vehicle from rolling forwards or
backwards.
The hill start assistance function
should not be used for prolonged
stops: use the brake pedal.
This function is not designed to im-
mobilise the vehicle permanently.
If necessary, use the brake pedal to
stop the vehicle.
The driver must remain particularly
vigilant when driving on slippery or
low-grip surfaces and/or on hills.
Risk of serious injury.

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.24
ENG_UD32713_2
Régulateur-limiteur de vitesse : fonction limiteur (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
Switching on
Press the side switch 1 . Warning
light 6 comes on, lit orange, and the
message “LIMIT” appears on the instru-
ment panel, accompanied by dashes to
indicate that the speed limiter function
is activated and waiting to store a lim-
ited speed.
To store the current speed, press
switch 2 (+): the limit speed will replace
the dashes.
The minimum stored speed is 20 mph
(30 km/h).
Controls
1 Main “On/Off” switch.
2 Limit speed activation, storage and increase switch (+).
3 Decreasing the limit speed (-).
4 Activation and recall of memorised limit speed (R).
5 Speed limiter function standby (with limited speed memory) (O).
The speed limiter function helps you
stay within the driving speed limit that
you choose, known as the limit speed.
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3)
1
2345
6

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.25
ENG_UD32713_2
Régulateur-limiteur de vitesse : fonction limiteur (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
Exceeding the limit speed
It is possible to exceed the limit speed
at any time. To do this: press the accel-
erator pedal firmly and fully (beyond
the resistance point).
While the speed is being exceeded, the
programmed speed displayed on the
instrument panel flashes.
Then, release the accelerator: the
speed limiter function will return as
soon as you reach a speed lower than
the stored speed.
Limited speed cannot be maintained
If driving up or down a steep gradient,
the system is unable to maintain the
limit speed: the stored speed will flash
on the instrument panel information dis-
play to inform you of this situation.
Varying the limit speed
The limit speed may be changed by re-
peatedly pressing:
– switch 2 (+) to increase speed;
– switch 3 (-) to reduce speed.
Driving
When a limited speed has been stored
and this speed is not reached, driving is
similar to driving a vehicle without the
speed limiter function.
Once you have reached the stored
speed, no effort on the accelera-
tor pedal will allow you to exceed
the programmed speed except in an
emergency (refer to information on
“Exceeding the limit speed”).
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3)
The speed limiter function is
in no way linked to the brak-
ing system.
23

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.27
ENG_UD32524_3
Régulateur-limiteur de vitesse : fonction régulateur (X52 - Dacia\
)
ENG_NU_993-5_X52_Dacia_2
The cruise control function helps you to
maintain your driving speed at a speed
that you choose, called the cruising
speed.
This cruising speed may be set at any
speed above 20 mph (30 km/h).
This function is an additio-
nal driving aid. However,
the function does not take
the place of the driver.
Therefore, it can under no circums-
tances replace the driver’s responsi-
bility to respect speed limits and to
be vigilant (the driver must always
be ready to brake).
Cruise control must not be used in
heavy traffic, on undulating or slip-
pery roads (black ice, aquaplaning,
gravel) and during bad weather (fog,
rain, side winds etc.).
There is a risk of accidents.
The cruise control function
is in no way linked to the
braking system.
Controls
1 Main “On/Off” switch.
2 Cruising speed activation, storage and increase switch (+).
3 Decreasing cruising speed (-).
4 Activation with recall of saved crui- sing speed (R).
5 Switch the function to standby (with cruising speed saved) (O).
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4)
1
2354

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.28
ENG_UD32524_3
Régulateur-limiteur de vitesse : fonction régulateur (X52 - Dacia\
)
ENG_NU_993-5_X52_Dacia_2
Driving
Once a cruising speed is stored and
the cruise control function is active,
you may lift your foot off the accelera-
tor pedal.
Important: you are never-
theless advised to keep
your feet close to the pedals
in order to react if neces-
sary.
Activating cruise control
At a steady speed (above 18 mph
(30 km/h approximately)) press switch 2
or (+): the function is activated and the
current speed is saved.
The cruising speed replaces the
dashes and the cruise control is confir-
med by the appearance of the message
“CRUISE” and the warning light 6

being lit green, as well as the warning
light 7
.
Switching on
Press switch 1 side .
The warning light 6 comes on, lit green,
and the message “CRUISE” appears
on the instrument panel, accompanied
by dashes to indicate that the cruise
control function is activated and waiting
to store a cruising speed.
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4)
1
23
76

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.29
ENG_UD32524_3
Régulateur-limiteur de vitesse : fonction régulateur (X52 - Dacia\
)
ENG_NU_993-5_X52_Dacia_2
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4)
Exceeding the cruising speed
The cruising speed may be exceeded
at any time by depressing the accele-
rator pedal. While it is being exceeded,
the cruising speed flashes on the ins-
trument panel.
Then, release the accelerator: after a
few seconds, the vehicle will automa-
tically return to its set cruising speed.
Cruising speed cannot be
maintained
When driving down a steep gradient,
the system is unable to maintain the
cruising speed: the stored speed will
flash on the instrument panel informa-
tion display to inform you of this situa-
tion.
Adjusting the cruising speed
The cruising speed may be changed by
pressing the following repeatedly:
– switch 2 (+) to increase the speed,
– switch 3 (-) to decrease the speed.
The cruise control function
is in no way linked to the
braking system.
23

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.31
ENG_UD26945_1
Aide au parking (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
This function is an addi-
tional aid that indicates the
distance between the vehi-
cle and an obstacle whilst
reversing, using sound signals.
Under no circumstances should it
replace the driver’s care or respon-
sibility whilst reversing.
The driver should always look out
for sudden hazards during driving:
always ensure that there are no
moving obstacles (such as a child,
animal, pram, bicycle, etc.) or small,
narrow objects such as stones or
posts in your path when manoeu-
vring.
Operating principle
Ultrasonic sensors, fitted in the vehi-
cle’s rear bumper, measure the dis-
tance between the vehicle and an ob-
stacle when reversing.
This measurement is indicated by
beeps which become more frequent the
closer you come to the obstacle, until
they become a continuous beep when
the vehicle is approximately 40 centi-
metres from the obstacle.
There is a beep when reverse gear is
engaged. If the beep sounds for a long
time (3 seconds), this signals an oper-
ating fault.
NB: ensure that the ultrasonic sensors
are not obscured (by dirt, mud, snow,
etc.).
PARKING DISTANCE CONTROL (1/2)
An impact to the under-
side of the vehicle while
manoeuvring (e.g.: strik-
ing a post, raised kerb or
other street furniture) may result in
damage to the vehicle (e.g.: defor-
mation of an axle).
To avoid any risk of accident, have
your vehicle checked by an ap-
proved dealer.

Downloaded from www.Manualslib.com manuals search engine JauneNoir Noir texte
2.35
ENG_UD34964_1
Boîte de vitesses robotisée (X52 - Dacia)
ENG_NU_993-5_X52_Dacia_2
Driving in manual mode
This mode can be activated at any time
when driving by pushing the lever to po-
sition M.
To shift up a gear, simply push the se-
lector lever backwards without neces-
sarily releasing the accelerator.
To shift down a gear, simply push the
selector lever forwards without neces-
sarily releasing the accelerator. The system will not tolerate a series
of up or down changes that cause the
engine to underrev or overrev.
By pushing the lever backwards twice,
you can move up two gears at a time
(except if under-revving). By pushing
the lever forwards twice, you can move
down two gears at a time (except if
over-revving).
When decelerating with the foot off the
pedal, the gears will automatically drop
to the low engine speed limit to avoid
stalling. The vehicle may be kept sta-
tionary (stop, red light etc.) by depress-
ing the brake pedal without shifting into
neutral N.The vehicle will move off again:
– either slowly, if you release the brake
without accelerating (e.g. when in a
traffic jam),
– or quickly, if you release the brake and accelerate.
Note: Neutral N may only be selected
when the vehicle is being driven or is
stationary or without touching the brake
pedal.
If the engine speed is too high or too
low, the system will choose the opti-
mum gear.
Manual mode can be deactivated and
reactivated at any time with the engine
running by moving the lever to position
D and respectively to M.
SEQUENTIAL GEARBOX (3/6)