2019 CITROEN C4 ESP

185
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
The tyre inflation pressures are given on this label.
This
 
k

it
 
i

s
 
i

nstalled
 
i

n
 
t

he
 
s

torage
 
b

ox,
 
u

nder
 
t

he
 
b

oot
 
floor.
This
 
kit
 
consists
 
of
 
a
 
compressor
 
and
 
a
 
sealant
 
c

artridge.
It allows the temporary repair
 

of
 
a
 
tyre.
You
 
are
 
then
 
able
 
to
 
go
 
to
 
the
 
nearest
 
garage.
It
 
is
 
designed
 
to
 
repair
 
most
 
punctures
 
which
 
c

ould affect the tyre, located on the tyre tread
or
 
shoulder.
Its
 
compressor
 
can
 
be
 
used
 
to
 
check
 
and
 
a

djust
 
the
 
pressure
 
of
 
the
 
tyre.
Temporary pu
ncture r epair k it
Access to the kit
List of tools
These tools are specific to your vehicle and can
vary
  according   to   equipment.   Do   not   use   them  
f

or   other   purposes.
1.
 1

2   V   compressor.
 C

ontains   a   sealant   cartridge   for   the  
t

emporary   repair   of   a   tyre   and   can   also   be  
u

sed   for   adjusting   tyre   pressures.
2.
 T

owing   eye.
For
  more   information   on   towing   refer   to   the  
c

orresponding
 s
ection.
8
In the event of a breakdown

188
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
F Switch  on   the   compressor   by   moving  t
he switch B to position "I" until the tyre
pressure
  reaches   2.0   bars.
 T

he   sealant   is   injected   into   the   tyre   under  
p

ressure;   do   not   disconnect   the   pipe   from  
t

he   valve   during   this   operation   (risk   of  
sp

lashing).
If
  after   around   5   to   7   minutes   the  
p

ressure is not attained, this indicates
that
  the   tyre   is   not   repairable;   contact  
a

  CITROËN   dealer   or   a   qualified  
w

orkshop   for   assistance. F
 R emove   the   kit   and   screw   the   cap   back   on  t
he   white   pipe.
 T

ake   care   to   avoid   staining   your   vehicle  
w

ith   traces   of   fluid.   Keep   the   kit   to   hand.
F
 
D
rive   immediately   for   approximately  
t

hree   miles   (five   kilometres),   at   reduced  
s

peed   (between   15   and   35   mph   (20   and  
6

0 km/h)),   to   plug   the   puncture.
F
 
S
top   to   check   the   repair   and   the   tyre  
p

ressure   using   the   kit.
Tyre under-inflation detection
After repair of the tyre, the warning lamp   will   remain   on   until   the   system   is  
r

einitialised.
For
  more   information   on   under-inflation  
d

etection,   refer   to   the   corresponding  
s

ection.
2. Inflation
F Turn the selector A to the "Air" position.
F
 
U
ncoil   the   black   pipe   H  
f
ully.
F
 
C
onnect   the   black   pipe   to   the  
v

alve   of   the   wheel.
In the event of a breakdown

190
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Checking tyre pressures / inflating accessories
You can also use the compressor, without injecting   any   product,   to:
-
 
c
heck   or   adjust   the   pressure   of   your   tyres,
-

i
nflate other accessories (balls, bicycle
tyres...).
F

T
urn the selector A to the
"Air" position.
F
 
U
ncoil   the   black   pipe   H  
f
ully.F
 C onnect   the   compressor's   electrical  
c

onnector   to   the   vehicle's   12   V   socket.
F
 
S
tart   the   vehicle   and   let   the   engine   run.
F
 
A
djust   the   pressure   using   the   compressor  
(

to   inflate:   switch   B in position "I";
 
t

o deflate:   switch   B in position "O" and
press button C ),
  according   to   the   vehicle's  
t

yre   pressure   label   or   the   accessory's  
p

ressure   label.
F
 
R
emove   the   kit   then   stow   it.Should
  the   pressure   of   one   or   more  
t

yres   be   adjusted,   it   is   necessary   to  
r

einitialise the under-inflation detection
system.
For
  more   information   on   under-inflation  
d

etection,   refer   to   the   corresponding  
s

ection.
F
 
C
onnect   the   black   pipe   to   the   valve   of   the  
w

heel   or   accessory.
I

f necessary, fit one of the adaptors
supplied
  with   the   kit   first.
In the event of a breakdown

191
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Spare wheel
The tools are installed in the boot under the
floor,  or   may   be   located,   depending   on   version,  
u

nder
 t
he
 f
ront
 p
assenger
 sea
t.
Access to the tools
List of tools
All of these tools are specific to your vehicle and
can  vary   according   to   the   level   of   equipment.   Do n

ot   use   them   for   other   purposes.
1.
 W

heelbrace.
 F

or   removing   the   wheel   trim   and   the   wheel  
bol

ts.
2.
 J

ack   with   integral   handle.
 F

or   raising   the   vehicle.
3.
 W

heel   bolt   cover   removal   tool.
 F

or   removing   the   wheel   bolt   covers   on   alloy  
w

heels
 o
r
 t
he
 c
entral
 w
heel
 c
ap
 (
depending
 o

n   version).
4.
 R

emovable   towing   eye.
For
  more   information   on   towing,   refer   to   the  
c

orresponding
 s
ection.
Procedure
 
for
 
changing
 
a
 
wheel
 
with
 
a
 
damaged
 
tyre
 
for
 
the
 
spare
 
wheel
 
using
 
the
 
tools
 
provided
 
with
 
the   vehicle.
Wheel with trim
When refitting the wheel
,   refit   the   trim  s
tarting   by   placing   its   notch   facing   the   valve  
a

nd   press   around   its   edge   with   the   palm   of  
y

our hand.
8
In the event of a breakdown

202
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
1. Sidelamps (W5W).
2. B rake   lamps   (P21W).
3.
 D

irection   indicators   (PY21W).
4.
 F

oglamp   or   reversing   lamp   (P21W).
Rear lamps
Changing bulbs
To reassemble, carry out these operations in reverse o rder.
F

S
pread the bulb holder retainers and
remove   the   bulb   holder.
F  
R
eplace   the   failed   bulb:
-  
f
or   the   sidelamp,   pull   the   bulb   (the   upper  
o

n e) o u t ,
-  
f
or   the   other   lamps,   turn   the  
c

orresponding   bulb   (lower)   a   quarter  
t

urn.
These
 
bulbs
 
are
 
changed
 
from
 
inside
 
the
 
boot.
F
 
O

pen
 
the
 
boot.
F
 
R

emove
 
the
 
corresponding
 
access
 
cover
 
in
 
t

he
 
trim
 
panel.
F
 
D

isconnect
 
the
 
lamp
 
unit
 
connector
 
a by
pressing
 
the
 
locking
 
button
 
(located
 
under
 
t

he
 
connector
 
for
 
the
 
right
 
hand
 
lamp
 
a

nd above the connector for the left hand
lamp),
F
 S
lacken
 
and
 
remove
 
the
 
nut
 
b ( take care
not to drop it inside the wing ).
F
 
P

ress
 
down
 
on
 
the
 
retaining
 
clip
 
for
 
lamp
 
u

nit c,
 
then
 
carefully
 
remove
 
it
 
towards
 
the
 
o

utside. Take
  care   to   engage   the   lamp   unit   in   its  
g

uides,   while   keeping   it   in   line   with   the  
v

ehicle.
Tighten
  sufficiently   to   ensure   sealing,  
b

ut   without   damaging   the   lamp.
In the event of a breakdown

206
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
CITROËN will not accept responsibility
for  the   cost   incurred   in   repairing   your  
v

ehicle   or   for   rectifying   malfunctions  
r

esulting   from   the   installation   of  
a

ccessories not supplied and not
recommended
  by   CITROËN   and  
n

ot installed in accordance with its
instructions, in particular when the
combined
  consumption   of   all   of   the  
a

dditional   equipment   connected  
e

xceeds
 1
0
 mil
liamperes.
Installing electrical
accessories
Your vehicle's electrical system is designed   to   operate   with   standard   or  
o

ptional
 e
quipment.
Before
  installing   other   electrical  
e

quipment   or   accessories   on   your  
v

ehicle, contact a CITROËN dealer or a
qualified
 w

orkshop.
In the event of a breakdown

210
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Engine compartment fuses
Access to the fuses
F Unclip  the   cover.
F  C hange   the   fuse   (see   corresponding  
par

agraph).
F

W
hen you have finished, close the cover
carefully
  to   ensure   correct   sealing   of   the  
f

usebox. Fuse
N° Rating
(A) Functions
F1 40Air
 c
onditioning.
F2 30 / 40Stop   &   Start.
F3 30Passenger
 c
ompartment
 f
usebox.
F4 70Passenger
 c
ompartment
 f
usebox.
F5 70Built-in   Systems   Inter face   (BSI).
F6 60Cooling   fan   assembly.
F7 80Built-in   Systems   Inter face   (BSI).
F8 15Engine
  management,   petrol   pump.
F9 15Engine
 m

anagement.
F10 15Engine
 m

anagement.
F11 20Engine
 m

anagement.
F12 5Cooling
  fan   assembly.
F13 5Built-in
  Systems   Inter face   (BSI).
F14 5Battery
  charge   unit   (non   Stop   &   Start   engine).
F15 5Stop
  &   Start.
F17 5Built-in
  Systems   Inter face   (BSI).
F18 10Right
  hand   main   beam   headlamp.
The
  fusebox   is   placed   in   the   engine  
c

ompartment   near   the   battery.
In the event of a breakdown

215
C4-cactus_en_Chap08_En-cas-de-panne_ed01-2016
Do not force the lever as locking will not   be   possible   if   the   clamp   is   not  
p

ositioned   correctly;   start   the   procedure  
ag

ain.
Quick release terminal
Disconnecting the (+) terminal
F Raise the lever A fully to release the clamp  B.
The
  Stop   &   Start   system   may   not   be  
o

perational   during   the   trip   following   the  
f

irst   engine   start.
In
  this   case,   the   system   will   only   be  
a

vailable   again   after   a   continuous  
p

eriod   of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   ambient  
t

emperature   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
It
 
is
 
recommended
 
that
 
the
 
battery
 
be
 
d

isconnected if the vehicle is not to be used
for
 
a
 
very
 
long
 
period,
 
so
 
as
 
to
 
maintain
 
an
 
a

dequate
 
state
 
of
 
charge
 
for
 
starting
 
the
 
e

ngine.
Before
 
disconnecting
 
the
 
battery:
F
 
c

lose
 
all
 
openings
 
(doors,
 
boot,
 
windows,
 
r

oof),
F
 
s

witch
 
off
 
all
 
electrical
 
consumers
 
(audio
 
s

ystem,
 
wipers,
 
lighting...),
F
 
s

witch
 
off
 
the
 
ignition
 
and
 
then
 
wait
 f
our minutes.
At
 
the
 
battery,
 
simply
 
detach
 
the
 
(+)
 
terminal.
Disconnecting the battery
Following reconnection of the battery, switch on t
he   ignition   and   wait   1   minute   before   starting   to  
p

ermit   initialisation   of   the   electronic   systems.  
H

owever,   if   problems   remain   following   this  
o

peration, contact a CITROËN dealer or a
qualified
 w

orkshop.
Referring
  to   the   corresponding   section,   you  
m

ust
 y
ourself
 r
einitialise
 (
depending
 o
n
 ve

rsion):
-
 
t
he   remote   control   key,
-
 ...
Following reconnection of the battery
Reconnecting the (+) terminal
F Position   the   open   clamp   B of the cable on
the   positive   post   (+)   of   the   battery.
F
 
P
ress   down   on   the   clamp   to   position   it  
c

orrectly   on   the   battery   post.
F
 
L
ock   the   clamp   by   lowering   the   lever   A.
8
In the event of a breakdown