2019 Alfa Romeo Stelvio brake light

WARNING
133)Never replace a fuse with another with
a higher amp rating; DANGER OF FIRE.
134)Before replacing a fuse, make sure
that the ignition device is at STOP and that
all devices are switched off and/or
disconnected.
135)Contact an Alfa Romeo Dealership if a
safety system (airbags, brakes),
transmission system (engine, gearbox) or
steering system general protection fuse
blows.
136)If a fuse blows again, contact an Alfa
Romeo Dealership.
137)If a general protective fuse
(MAXI-FUSE, MEGA-FUSE, MIDI-FUSE)
blows, contact an Alfa Romeo Dealership.
IMPORTANT
56)Never replace a fuse with metal wires or
anything else.
57)If it is necessary to wash the engine
compartment, take care not to directly hit
the fuse box and the window wiper motors
with the water jet.
CHANGING A WHEEL
GENERAL INSTRUCTIONS
The car is equipped with the "Tire Repair
Kit": see the “Tire Repair Kit” paragraph
for how to use this device.
As an alternative to the “Tire Repair Kit”,
the car may be requested with a
space-saver wheel: see the instructions
on the following pages for changing the
wheel.
JACK
138) 139)
Please note that:
the jack weighs about 4.4 lb (2 kg);
the jack requires no adjustment;
the jack cannot be repaired and in the
event of a fault it must be replaced by
another genuine one;
no tool other than its cranking device
may be fitted on the jack.
Jack maintenance:
prevent any dirt from depositing on
the "worm screw";
keep the "worm screw" lubricated;
never modify the jack.
Conditions in which not to use the jack:
temperatures below −40°F (-40°C);
on sandy or muddy ground;
on uneven ground;
on steep slopes in extreme weather
conditions: thunderstorms, typhoons,hurricanes, blizzards, storms, etc.;
in direct contact with the engine or for
repairs under the car;
on boats.
CHANGING PROCEDURE
140) 141) 142) 143) 144) 145) 146)
58) 59)
Proceed as follows:
stop the car in a position that is not
dangerous for oncoming traffic where
you can change the wheel safely.
The ground must be flat and
sufficiently compact;
stop the engine, engage the hazard
warning lights and the parking brake;
engage P (Park) mode;
wear the reflective safety jacket
(compulsory by law) before getting out of
the car;
open the luggage compartment and lift
up the mat using the handle;
when the situation dictates it (for your
own safety and to comply with the
regulations in force in the country where
you are), take the warning triangle and
position it at a suitable distance from the
car;
unscrew the locking device 1 fig. 157,
take out the space-saver wheel and the
inflation compressor;
157

IMPORTANT The sealing liquid is
effective for outside temperatures
between -40°F and +122°F (-40°C and
+50°C). The sealant has an expiry date.
REPAIR PROCEDURE
147) 148) 149) 150) 151) 152) 153) 154) 155) 156)
Proceed as follows:
stop the car in a position that is not
dangerous for oncoming traffic where
you can repair the tyre safely, as far as
possible from the side of the road;
turn on the hazard warning lights;
engage the electric parking brake;
engage P (Park) mode;
stop the engine and put on the
reflective safety jacket (for your own
safety and to comply with the regulations
in force in the country where you are)
before getting out of the car.
when the situation requires it (for your
own safety and to comply with theregulations in force in the country where
you are), take the warning triangle from
the luggage compartment and position it
at a suitable distance from the car.
put on the gloves, connect the hose 5
fig. 163 to the cannister 1 using the
fitting 6. Unscrew the tyre valve cap and
screw the filler hose ring nut 2 onto the
tyre valve;
make sure that the switch 7
fig. 164 on the compressor 4 is in the 0
(off) position;
insert the plug into the socket in the
passenger compartment or in the
luggage compartment fig. 165 and start
the engine;
start the compressor by putting the
switch 7 fig. 164 in the I (on) position;
inflate the tyre to a pressure of at
least 32 psi (2.2 bar). In order to obtain a
more precise reading, check the pressure
value on pressure gauge 8 with the
16208066V0002EM
16308066V0004EM
16408066V0005EM
16508066V0006EM
161
compressor off;

if a pressure of at least 26 psi (1.8 bar)
is not reached within 15 minutes, the tyre
is too damaged to be repaired. Do not
continue driving, but contact an Alfa
Romeo Dealership;
after having driven for about 5 miles
(8 km), stop, engage the electric parking
brake and recheck the tyre pressure;
if the measured pressure is unchanged
(32 psi (2.2 bar)), continue driving to an
Alfa Romeo Dealership;
if the measured pressure is between
19 and 30.5 psi (1.3 and 2.1 bar), restore
pressure to 32 psi (2.2 bar), continue
driving to an Alfa Romeo Dealership;
if the measured pressure is lower than
19 psi (1.3 bar), the tyre is too damaged
to be repaired. Do not continue driving,
but contact an Alfa Romeo Dealership.
IMPORTANT Only use original tyre repair
cannisters, which can be purchased at an
Alfa Romeo Dealership.
IMPORTANT To conserve the battery
charge, it is recommended to leave the
vehicle running for the entire inflation
process.
WARNING
147)Punctures on the sides of the tire may
not be repaired. Do not use the Tire Repair
kit if the tyre was damaged as a result of
being used when underinflated.
148)Always wear protective gloves before
proceeding with the operation.
149)Apply the adhesive label where it can
be easily seen by the driver as a reminder
that the tyre has been treated with the Tire
Repair Kit. Drive carefully, particularly on
bends. Do not exceed 80 km/h. Avoid sudden
acceleration or braking.
150)You must always indicate that the tyre
was repaired using the Tire Repair Kit.
151)Repairs are not possible in the case of
damage to the wheel rim (bad groove
distortion causing air loss). Do not remove
foreign bodies (screws or nails) from the
tyre.
152)Never operate the compressor for
longer than 20 consecutive minutes. Risk of
overheating. The Tire Repair Kit is not
suitable for definitive repairs, so the
repaired tyres may only be used temporarily.
153)As required by current regulations, the
information on chemical substances for the
protection of human health and the
environment and on the safe use of the
sealing fluid are on the cannister label.
Compliance with the indications on the label
is an essential condition to ensure the safety
and the effectiveness of the product.
Remember to carefully read the label before
use; the user of the product is responsible
for any damages caused by improper use.
The sealing fluid has an expiry date. Replace
the bottle if the sealant has expired.154)If the pressure falls below 1.3 bar, do
not drive any further: the Tire Repair Kit
cannot guarantee proper seal because the
tyre is too damaged. Contact an Alfa Romeo
Dealership.
155)The Tire Repair Kit provide a
temporary repair, therefore the tyre must be
examined and repaired by a specialist as
soon as possible. The sealant is suitable for
use at temperatures in the range from −40°C
to +50°C.
156)Indicate the presence of the stationary
car in accordance with current regulations:
hazard warning lights, warning triangle, etc.
Those on board should get out of the vehicle
and wait for the wheel to be repaired away
from the threat posed by the traffic. If
parked on a slope or rough surface, chock
the wheels with wedges or other suitable
devices (for the correct procedure for
parking the car safely, refer to the "Parking"
paragraph in the "Starting and driving"
chapter).
IMPORTANT
60)In the event of a puncture caused by
foreign bodies, the kit may be used to repair
tyres showing damage on the tyre tread up
to max. 6mm diameter.
IMPORTANT
3)Dispose of the bottle and the sealant
liquid properly. Have them disposed of in
compliance with national and local
regulations.
162
IN AN EMERGENCY

SCHEDULED SERVICING
Correct servicing is crucial for
guaranteeing a long life for the vehicle
under the best conditions.
For this reason, Alfa Romeo has planned
a series of checks and maintenance
operations at fixed distance intervals
and, for versions/markets, where
provided, at fixed time intervals, as
described in the Service Schedule.
Before each service, it is always
necessary to carefully follow the
instructions in the Scheduled Servicing
Plan (e.g. periodically check level of
fluids, tyre pressure, etc.).
Scheduled Servicing is offered by an Alfa
Romeo Dealership according to a set
time schedule. If, during each operation,
in addition to the ones scheduled, the
need arises for further replacements or
repairs, these may be carried out with the
owner's explicit consent only.
IMPORTANT Scheduled Servicing
operations are required by the
Manufacturer. Failure to have them
carried out may invalidate the warranty.
It is advisable to inform the Alfa Romeo
Dealership of any small operating
irregularities without waiting for the next
service.
REGULAR
CHECKS
Every
year
or
620
miles
(
1,000
km)
or

before
long
journeys,
check
and
top
up,
if

necessary:
engine
coolant
level;
brake
fluid
level
(if
insufficient,
see
an

Alfa
Romeo
dealership
as
soon
as

possible);
low
AdBlue
diesel
emissions
additive

(UREA)
level
warning
(2.2
JTD
versions

only);
windscreen washer fluid level;
tyre inflation pressure and condition;
operation of lighting system
(headlights,
direction
indicators,
hazard

warning
lights,
etc.);
operation
of
screen
washing/wiping

system
and
positioning/wear
of
wiper

blades.
…ˆ
‹Š
‹Š
‹Š€…
Ž
„1860
miles
(
3,000
km)

}Š€


»Šƒ…Š
ˆ
}Š€
}Ž





 


‚

‚‹ˆˆ‹“…Šƒ
‹Š€…





€‘






‰…ˆ







€…
‹‚
…Š}





…Š

…Š}
the
following
checks
must
be
carried
out

more
often
than
indicated
in
the

Scheduled
Servicing
Plan:
check
front
and
rear
disc
brake
pad

condition
and
wear;
check
cleanliness
of
bonnet
and

tailgate
locks,
cleanliness
and
lubrication

of
linkage;
visually
inspect
conditions
of:
engine,

gearbox,
transmission,
pipes
and
hoses

(exhaust/fuel
system/brakes)
and

rubber

elements
(gaiters/sleeves/bushes,
etc.);
check
battery
charge
and
battery
fluid

level
(electrolyte);
visually
inspect
conditions
of
the

accessory
drive
belts;
check
and,
if
necessary,
change
engine

oil
and
replace
oil
filter;
check
and,
if
necessary,
replace
pollen

filter;
check
and,
if
necessary,
replace
air

cleaner;
check
and,
if
necessary,
replace
the

Bad
Fuel
filter

(where
provided).170
SERVICING AND CARE

Thousands of miles9 18273645546372 8190
Years12345678 910
Change engine oil and replace oil filter(4)
Replace Transfer Case oil (for AWD versions)
●
Spark plug replacement(5)●●
Replace accessory drive belt/s(3)
Replace air cleaner cartridge(6)
●●●
Change the brake fluid(6)
Replace the passenger compartment cleaner(6)
o●o●o●o●o●
(4) The actual interval for changing engine oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or message in
the instrument panel. In any cases, never exceed 1 year.
(5) The replacement must be performed according to mileage and regards of the elapsed time. The following are vital in order to ensure correct operation and prevent
serious damage to the engine: - only use spark plugs specifically certified for the engine itself of the same type and brand (see the "Engine" paragraphin the "Technical
specifications" chapter); - strictly comply with the spark plug replacement intervals in the Scheduled Servicing Plan. It is advisable to contact a reference Dealership for
plug replacement. (3) The maximum mileage is 36,000 mi (60,000 km). The belt must be replaced every 4 years, regardless of distance travelled. If the vehicle is used in heavy conditions
(dusty areas, especially severe weather conditions, very low or very high temperatures for extended periods, urban driving, long periods of idling), the maximum
mileage is 18.000 mi (30.000 km). The belt must be replaced every 2 years regardless of the mileage
(6) If the car is used in dusty areas, this cleaner should be replaced every 9,000 miles (15,000 km).
(o) Recommended operations
(●) Mandatory operations
173
Thousands ofkilometres15 30 45 60 75 90 105 120135150

SCHEDULED SERVICING PLAN (2.2 JTD diesel engine versions)
IMPORTANT Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the
frequency indicated in the plan by marking each operation with a dot or dedicated note. Warning: simply restarting the maintenance
from the start of the plan may cause the allowed interval to be exceeded for some operations!
Thousands of miles12 24 36 48 60 72 84 96 108 120
Years12345678910
Check battery charge status with the proper instrument●●●●●●●●●●
Check tyre condition/wear and adjust pressure, if necessary.
Check quick tyre repair kit recharge conditions/expiry date
(if provided)
●●●●●●●●●●
Check operation of lighting system (headlights, direction
indicators, hazard warning lights, boot, passenger
compartment, glove compartment, instrument panel warning
lights, etc.)
●●●●●●●●●●
Check and, if necessary, top up fluid levels in engine
compartment (engine coolant, hydraulic clutch/brakes,
windscreen washer, battery, etc.)(1) (2)
●●●●●●●●●●
Check exhaust emissions●●●●●●●●●●
Use the diagnosis socket to check the fuel/engine control
system operation, emissions and the engine oil
deterioration(3)
●●●●●●●●●●
(1) Always only use the liquids shown in the handbook for topping up after having checked that the system is not damaged.
(2) The consumption of AdBlue (UREA) additive depends on the conditions of the use of the car and is indicated by means of the symbol and a specific messageonthe
instrument panel display.
(3) If the engine oil quality detected by the vehicle diagnostics is lower than 20%, it is advisable to replace the engine oil and engine filter in order to avoid another service
operation after a short time.
174
SERVICING AND CARE
Thousands ofkilometres20 40 60 80 100 120 140 160 180200

Thousands of miles12 24 36 48 60 72 84 96 108 120
Years12345678910
Visually inspect conditions of: exterior bodywork, underbody
protection, pipes and hoses (exhaust, fuel system, brakes),
rubber elements (gaiters, sleeves, bushes, etc.)
●●●●●
Check windscreen and rear window wiper blade
position/wear●●●●●
Check operation of the windscreen wiper/washer system
and adjust jets, if necessary●●●●●
Check cleanliness of bonnet and luggage compartment locks,
cleanliness and lubrication of linkage●●●●●
Visually inspect conditions and wear of front disc brake pads
and operation of pad wear indicators●●●●●●●●●●
Visually inspect conditions and wear of rear disc brake pads
and operation of pad wear indicators●●●●●●●●●●
Visually inspect the condition and tensioning of the
accessory drive belt(s)(4)●●
Visually inspect the toothed timing drive belt(4)●●
Change engine oil and replace oil filter(5)
(4) The maximum mileage is 72,000 mi (120,000 km). The belt must be replaced every 5 years, regardless of distance travelled. If the vehicle is used in heavy conditions
(dusty areas, especially severe weather conditions, very low or very high temperatures for extended periods, urban driving, long periods of idling), the maximum
mileage is 36,000 mi (60,000 km). The belt must be replaced every 4 years regardless of the mileage
(5) The actual interval for changing engine oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or message in
the instrument panel. In any case, it must never exceed 2 years. Where the car is used mostly in urban settings you need to replace the engine oil filter every year.
175
Thousands ofkilometres20 40 60 80 100 120 140 160 180200

ENGINE COMPARTMENT
CHECKING LEVELS
165) 166)
63)
2.0 T4 MAir engine
1. Engine oil filler 2. Primary engine cooling reservoir plug 3. Brake fluid reservoir cap access cover 4. Windscreen/headlights
washer fluid reservoir cap 5. Secondary engine cooling reservoir plug
17209026V0002EM
177