2019 Alfa Romeo Giulia instrument panel

Thousands of miles9 18273645546372 8190
Years12345678 910
Change engine oil and replace oil filter(4)
Replace Transfer Case oil (for AWD versions)
●
Spark plug replacement(5)●●
Replace accessory drive belt/s(3)
Replace air cleaner cartridge(6)
●●●
Change the brake fluid(7)
Replace the passenger compartment cleaner(6)
o●o●o●o●o●
(4) The actual interval for changing engine oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or message in
the instrument panel. In any cases, never exceed 1 year.
(5) The replacement must be performed according to mileage and regards of the elapsed time. The following are vital in order to ensure correct operation and prevent
serious damage to the engine: - only use spark plugs specifically certified for the engine itself of the same type and brand (see the "Engine" paragraphin the "Technical
specifications" chapter); - strictly comply with the spark plug replacement intervals in the Scheduled Servicing Plan. It is advisable to contact a reference Dealership for
plug replacement. (3) The maximum mileage is 36,000 mi (60,000 km). The belt must be replaced every 4 years, regardless of distance travelled. If the vehicle is used in heavy conditions
(dusty areas, especially severe weather conditions, very low or very high temperatures for extended periods, urban driving, long periods of idling), the maximum
mileage is 18.000 mi (30.000 km). The belt must be replaced every 2 years regardless of the mileage
(6) If the vehicle is used in dusty areas, this cleaner should be replaced every 9,000 miles (15,000 km).
(7) The brake fluid replacement has to be done every two years, irrespective of the mileage.
(o) Recommended operations
(●) Mandatory operations
163
Thousands ofkilometres15 30 45 60 75 90 105 120135150

SCHEDULED SERVICING PLAN (2.2 JTD diesel engine versions)
IMPORTANT Once you have carried out the last intervention in the table, continue with the scheduled servicing, maintaining the
frequency indicated in the plan by marking each operation with a dot or dedicated note. Warning: simply restarting the maintenance
from the start of the plan may cause the allowed interval to be exceeded for some operations!
Thousands of miles12 24 36 48 60 72 84 96 108 120
Years12345678910
Check battery charge status with the proper instrument●●●●●●●●●●
Check tyre condition/wear and adjust pressure, if necessary.
Check quick tyre repair kit recharge conditions/expiry date
(where provided)
●●●●●●●●●●
Check operation of lighting system (headlights, direction
indicators, hazard warning lights, boot, passenger
compartment, glove compartment, instrument panel warning
lights, etc.)
●●●●●●●●●●
Check and, if necessary, top up fluid levels in engine
compartment (engine coolant, hydraulic clutch/brakes,
windscreen washer, battery, etc.)(1) (2)
●●●●●●●●●●
Check exhaust emissions●●●●●●●●●●
(1) Always only use the liquids shown in the handbook for topping up after having checked that the system is not damaged.
(2) The consumption of AdBlue (UREA) emission control additive depends on the conditions of the use of the car and is indicated by means of the symbol anda specific
message on the instrument panel display.
164
SERVICING AND CARE
Thousands ofkilometres20 40 60 80 100 120 140 160 180200

Thousands of miles12 24 36 48 60 72 84 96 108 120
Years12345678910
Visually inspect the toothed timing drive belt(4)●●
Change engine oil and replace oil filter(5)
Replace Transfer Case oil (for AWD versions)
●
Replace accessory drive belt/s(4)
Replace the toothed timing drive belt(4)
Replace air cleaner cartridge(6)
●●●
Replace fuel filter cartridge(7)●●●
Change the brake fluid(8)
Replace the passenger compartment cleaner
●●●●●
(4) The maximum mileage is 72,000 mi (120,000 km). The belt must be replaced every 5 years, regardless of distance travelled. If the vehicle is used in heavy conditions
(dusty areas, especially severe weather conditions, very low or very high temperatures for extended periods, urban driving, long periods of idling), the maximum
mileage is 36,000 mi (60,000 km). The belt must be replaced every 4 years regardless of the mileage
(5) The actual interval for changing engine oil and replacing the engine oil filter depends on the vehicle usage conditions and is signalled by the warning light or message in
the instrument panel. In any case, it must never exceed 2 years. Where the car is used mostly in urban settings you need to replace the engine oil filter every year.
(6) If the car is used in dusty areas, this cleaner should be replaced every 12,000 miles (20.000 km).
(7) If the car runs on fuel with quality below the relevant European specification, this filter must be replaced every 12,000 miles (20.000 km).
(8) The brake fluid replacement has to be done every two years, irrespective of the mileage.
(O) Recommended operations
(●) Mandatory operations
166
SERVICING AND CARE
Thousands ofkilometres20 40 60 80 100 120 140 160 180200

ENGINE OIL
158)66)
IMPORTANT
It
is
advisable
to
check
the

oil
level
indication
before
long
journeys.
The
engine
oil
level
can
be
seen
on
the

instrument
panel
display
every
time
the

engine
is
started,
or
on
the
Connect

system
display
by
activating
on
the
main

menu
(MENU
button)
the
following

functions
in
sequence:
“Apps”;
“Car

Status”
and
“Oil
Level”.
Check
on
the
display
using
the
6
notches

that
the
oil
level
is
between
MIN
and

MAX
level:
1
notch
MIN
level,
6
notches

MAX
level.
If
the
oil
level
indication

reaches
the
first
red
mark,
add
oil

through
the
filler
1,
considering
that
each

notch
shown
on
the
display
corresponds

to
approximately:
2.0
T4
MAir
engine
0.055
UK
gal

(250
ml).
2.2
JTD
Engine







Õ
c
Õ
Ú
Ø

ƒ}ˆ
¦
×
Õ
Õ
‰ˆ
¡
c







‚

‹ŽŽ


67)
IMPORTANT
Make
sure
not
to
add
too

much
engine
oil
when
topping
up.
Engine

oil
in
excess
may
damage
the
engine.

Have
the
car
checked.
Never
exceed
the

MAX
level
when
topping
up
engine
oil.
It
is advisable to check the oil level in
intermediate steps on the display.
IMPORTANT The oil level is not refreshed
immediately on the display after topping
up. Consequently, wait for the oil level to
be refreshed on the display following to
procedure shown below.
Top-up and oil level indication update
on display
If a top-up is needed, proceed as follows
to ensure correct indication of the oil
level on the display:
2.0 T4 MAir engine
with the vehicle level, run the engine
for approximately 5 minutes
(temperature higher than 176°F (80°C)
and then stop the engine;
start the engine again and idle it for
about 2 minutes.
2.2 JTD Engine
with the car level, run the engine until
the second oil temperature notch lights
up on the display on the instrument panel,
then stop the engine;
wait for at least 3 minutes, turn the
ignition switch to ON without starting the
engine and wait for 20 seconds.
IMPORTANT If the indication is not
correct after the procedure, contact an
Alfa Romeo Dealership.IMPORTANT The oil dipstick in the engine
compartment, on versions with 2.2 JTD
engine, must be used ONLY if the oil level
sensor is faulty. The latter condition is
indicated by the
symbol which will
appear on the instrument panel.
The manual engine oil level checking
procedure must be carried out, when
necessary, on a cold engine only.
Never attempt to carry out the manual
engine oil checking procedure (using the
dipstick) with the engine hot. Contact
with the surrounding hot engine parts
could cause burns.
This operation is permitted only for the
time actually needed to restore correct
operation of the oil level sensor at an Alfa
Romeo dealership.
Engine oil consumption
68)
4)
The maximum engine oil consumption is
usually 0.88 lb (400 grams every
620 miles (1000 km). When the car is
new, the engine needs to be run in,
therefore the engine oil consumption can
only be considered stabilised after the
first 3100 - 3700 miles (5000 -
6000 km).
170
SERVICING AND CARE

ENGINE COOLANT FLUID
159)
69)
If the level is too low, unscrew the
reservoir cap and add the fluid described
in the "Technical Specifications" chapter.
On the 2.0 T4 MAir engine version with
right-hand drive, remove the shield 6
fig. 154 to check the fluid level in the
primary reservoir. To do this, release the
fixing clip 7 and lift upwards.
WASHER FLUID FOR WINDSCREEN/
HEADLIGHTS
160) 161)
The windscreen and headlights washer
fluid reservoir (where provided) is
equipped with a telescopic filler. If the
level is too low, lift the reservoir cap 4
fig. 155 upwards and then lift the filler,
as shown in the figure, and add the fluiddescribed in the "Technical
Specifications" chapter. After having
topped up the fluid, arrange the filler
correctly and then press on the cap until
you hear it click.
IMPORTANT With a low fluid level
(indicated by the dedicated symbol
appearing on the instrument panel
display), the headlight washer system
does not work, even though the screen
washers continue to work.BRAKE FLUID
Check that the fluid is at the max. level. If
the liquid level in the tank is insufficient,
contact an Alfa Romeo Dealership to
have the system checked.
AUTOMATIC TRANSMISSION
ACTIVATIONSYSTEM OIL
5)
The transmission control oil level should
only be checked at an Alfa Romeo
Dealership.
BATTERY
162) 163) 164) 165)
70)
6)
The battery does not require the
electrolyte to be topped up with distilled
water. A periodic check carried out at an
Alfa Romeo Dealership is, however,
necessary to check efficiency.
Follow the battery manufacturer's
instructions for maintenance.
Useful advice for extending the life of
your battery
To avoid draining your battery and make
it last longer, observe the following
instructions:
when you park the car, ensure that the
doors, tailgate and bonnet are closed
properly, to prevent any lights from
15409026S0007EM
15509086S0666EM
171

83)Avoid washing with rollers and/or
brushes in washing stations. Wash the car
only by hand using neutral pH detergents; dry
it with a wet chamois leather. Abrasive
products and/or polishes should not be used
for cleaning the car. Bird droppings must be
washed off immediately and thoroughly as
the acid they contain is particularly
aggressive. Avoid (if at all possible) parking
the vehicle under trees; remove vegetable
resins immediately as, when dried, it may
only be possible to remove them with
abrasive products and/or polishes, which is
highly inadvisable as they could alter the
typical opaqueness of the paint. Do not use
pure windscreen washer fluid for cleaning
the front windscreen and rear window; dilute
it min. 50% with water. Only use pure screen
washer fluid when strictly necessary due to
outside temperature conditions.
IMPORTANT
7)Detergents pollute the environment. Only
wash your vehicle in areas equipped to
collect and treat wastewater from this type
of activity.
INTERIOR
174) 175) 176)
Periodically check the cleanliness of the
interior, beneath the mats, which could
cause oxidation of the sheet metal.
PLASTIC AND COATED PARTS
84)
Clean interior plastic parts with a damp
cloth (if possible made from microfibre),
and a solution of water and neutral,
non-abrasive detergent.
To clean oily or persistent stains, use
specific products free from solvents and
designed to maintain the original
appearance and colour of the
components.
Remove any dust using a microfibre
cloth, if necessary moistened with water.
The use of paper tissues is not
recommended as these may leave
residues.
WARNING
174)Never use flammable products, such as
petrol ether or rectified petrol to clean the
inside of the car. The electrostatic charges
which are generated by rubbing during the
cleaning operation may cause a fire.
175)Do not keep aerosol cans in the car:
they might explode. Aerosol cans must not
be exposed to a temperature exceeding
50°C. When the vehicle is exposed to
sunlight, the internal temperature can
greatly exceed this value.
176)There must be no obstacles on the
floor underneath the pedals; make sure that
mats are always flat and do not interfere
with the pedals.
177)Do not use aggressive organic
substance such as: gasoline, kerosene, oil,
acetone or solvents.
IMPORTANT
84)Never use alcohol, petrols and
derivatives to clean the dashboard and
instrument panel lens.
179

Passenger's airbag
(where provided)
The options available are:
"Sound & Display": the system warns
the driver that an obstacle is present
through acoustic (via the speakers in the
car) and visual (on the instrument panel)
warnings;
"Sound Only": the system warns the
driver that an obstacle is present through
acoustic indications only, via the
speakers in the car;
"Off": system disengaged.
Lets you activate/deactivate the front
passenger airbag function. When the
function is accessed, the system will
detect the activation/deactivation status
of the airbags and confirm change of
status. Press the Rotary Pad to continue.
The air bag status is visible through the
LEDs next to the status icon on the
dashboard.
Passenger protection activated: the ON
LED switches on with a steady light.
Passenger protection deactivated: the
OFF LED switches on with a steady light.
Seat belt reminder
This function appears only if the seat belt
reminder was deactivated and allows to
reactivate it.Driver assistance
To access the “Driver assistance”
function, select it by turning the Rotary
Pad and press the Rotary Pad to activate.
This function can be used to carry out the
following adjustments:
ParkSense
This function can be used to select the
type of warning provided by the
ParkSense system.
The options available are:“Mode”: the following options are
available in this function: “Sound”, the
system notifies the driver of the
presence of an obstacle by means of
auditory signals only, by means of the
speakers in the car or “Sound and
Display”, the system notifies the driver of
the presence of an obstacle by means of
auditory signals (by means of the
speakers in the vehicle) and visual
signals, on the instrument panel display.
"Audio": allows to select the volume of
the acoustic warnings provided by the
ParkSense system, the available options
are: "High", "Medium" or "Low".Rear view camera
(where provided)
This function can be used to carry out the
following adjustments:
"View": lets you activate viewing the
video camera on the display;
“Switch-Off Delay”: allows you to delay
switching the camera off by a few
seconds when reverse gear is
disengaged.
“Camera Guidelines”: Allows you to
enable the dynamic guidelines on the
display to indicate the vehicle’s path.
Automatic parking brake
This function allows you to
activate/deactivate the automatic
parking brake engagement upon
switching off the engine.
Brake service
(where provided)
This function permits the activation of
the procedure to carry out braking
system maintenance.
Easy Entry
(where provided)
This function can be used to
activate/deactivate front seat retraction
(Easy Entry function). The default setting
is “Off”.
215

PRIVACY MODE
Privacy mode lets you disable the “Find
car”, “Notify Area” and “Notify Speed”
services for a certain time.
IMPORTANT Vehicle position tracing
remains active for the assistance
services, where provided, in the event of
accident or vehicle theft, but is not visible
to the customer.
PRIVACY MODE activation procedure
Proceed as follows:
take note of the total odometer
reading;
make sure that the instrument panel is
off;
send the following text message to
+393424112613: “PRIVACY

” (e.g.: PRIVACY
ZAR00000ABC001). You can find the
chassis number in the registration
document;
before starting the engine, wait to
receive the text message confirming that
Privacy mode has been activated and
indicating when it expires.When you have received the
confirmation, you can start your trip in
the knowledge that the vehicle will not be
traced until the indicated expiry time. If it
expires while you are still travelling,
Privacy mode will be extended until you
turn off the engine (instrument panel off).
If you receive a text message indicating
that your request was not successful, you
must be aware that the vehicle will
continue to be visible to the registered
customer. If you have any problems
during activation, consult the FAQ on the
www.alfaromeoconnect.eu portal,
contact the Alfa Romeo Service Network
or contact Customer Care.
220
MULTIMEDIA