2019 Alfa Romeo Giulia transmission

ENGINE COOLANT FLUID
159)
69)
If the level is too low, unscrew the
reservoir cap and add the fluid described
in the "Technical Specifications" chapter.
On the 2.0 T4 MAir engine version with
right-hand drive, remove the shield 6
fig. 154 to check the fluid level in the
primary reservoir. To do this, release the
fixing clip 7 and lift upwards.
WASHER FLUID FOR WINDSCREEN/
HEADLIGHTS
160) 161)
The windscreen and headlights washer
fluid reservoir (where provided) is
equipped with a telescopic filler. If the
level is too low, lift the reservoir cap 4
fig. 155 upwards and then lift the filler,
as shown in the figure, and add the fluiddescribed in the "Technical
Specifications" chapter. After having
topped up the fluid, arrange the filler
correctly and then press on the cap until
you hear it click.
IMPORTANT With a low fluid level
(indicated by the dedicated symbol
appearing on the instrument panel
display), the headlight washer system
does not work, even though the screen
washers continue to work.BRAKE FLUID
Check that the fluid is at the max. level. If
the liquid level in the tank is insufficient,
contact an Alfa Romeo Dealership to
have the system checked.
AUTOMATIC TRANSMISSION
ACTIVATIONSYSTEM OIL
5)
The transmission control oil level should
only be checked at an Alfa Romeo
Dealership.
BATTERY
162) 163) 164) 165)
70)
6)
The battery does not require the
electrolyte to be topped up with distilled
water. A periodic check carried out at an
Alfa Romeo Dealership is, however,
necessary to check efficiency.
Follow the battery manufacturer's
instructions for maintenance.
Useful advice for extending the life of
your battery
To avoid draining your battery and make
it last longer, observe the following
instructions:
when you park the car, ensure that the
doors, tailgate and bonnet are closed
properly, to prevent any lights from
15409026S0007EM
15509086S0666EM
171

IMPORTANT
4)Used engine oil and oil filters contain
substances which are harmful to the
environment. To change the oil and filters, we
advise you to contact an Alfa Romeo
Dealership.
5)Used transmission fluid contains
substances that are harmful to the
environment. You are advised to contact an
Alfa Romeo Dealership for oil changes.
6)Batteries contain substances which are
very dangerous for the environment. For
battery replacement, contact an Alfa Romeo
Dealership.
BATTERY RECHARGING
IMPORTANT NOTES
166) 167)
IMPORTANT Before using the charging
device, always make sure that it is
appropriate for the installed battery,
with constant voltage (below 14.8 V) and
low amperage (maximum 15 A).
IMPORTANT Recharge the battery in a
well ventilated environment.
IMPORTANT Never charge or recharge a
frozen battery: it may explode because
of the nitrogen trapped inside the ice
crystals.
IMPORTANT At all times while charging
or recharging the battery, make sure that
any sparks or open flames are kept
sufficiently far away from the battery.
IMPORTANT Before using any devices to
charge or to maintain the charge of the
battery, carefully follow the instructions
provided with the device in order to
properly and safely connect it to the car
battery.
You can recharge the battery without
disconnecting the wires of the vehicle's
electrical system.
To reach the battery, remove the
access panel inside the boot fig. 156;
remove the protective cover 1
fig. 157 and connect the positive cable
terminal of the charger (usually red) to
the positive terminal (+) of the battery;
connect the negative terminal of the
charger (usually black) to nut 2 next to
the negative terminal (-) of the battery, as
shown in fig. 157;
The vehicle is equipped with an IBS
(Intelligent Battery Sensor), which is able
15609036S0001EM
15709036S0002EM
173

73)The vehicle is equipped with fluids which
are optimised or protecting its performance
and life and extending service intervals. Do
not use chemicals for washing these
components since they may damage the
engine, the transmission or the climate
control system. This damage is not covered
by the vehicle’s warranty. If any component
needs to be washed due to malfunctioning,
use only the specific liquid for that
procedure.
74)An excessive or insufficient amount of
oil inside the base is extremely damaging to
the engine. Make sure it is always at an
adequate level.
75)Vehicles equipped with catalytic
converter must be fuelled only with unleaded
petrol. Leaded petrol would permanently
damage the catalytic converter and
eliminate its ability to reduce polluting
emissions, seriously compromising the
engine performance, which would be
irreparably damaged. If the engine does not
work correctly, especially if it starts
irregularly or if there is a reduction of its
performance, immediately go to an Alfa
Romeo Dealership. Prolonged and faulty
operation of the engine may cause
overheating of the converter and, as a
consequence, possible damage to the
converter and the vehicle.
76)Using a gearbox fluid different from that
approved may compromise gearshifting
quality and/or cause vibration of the
gearbox itself.77)It is recommended to have the vehicle
serviced by an Alfa Romeo Dealership. When
carrying out normal periodic operations and
small servicing interventions personally on
the vehicle, it is recommended to use
suitable equipment, genuine spare parts and
the necessary fluids. Do not carry out any
interventions if you don't have the necessary
experience.
78)When you need to disconnect or remove
the battery, do not close the boot. Open the
boot manually if it is locked.
79)Always require the use of only
compressor coolants and lubricants
approved and suitable for the specific air
conditioning system fitted on the vehicle.
Some non-approved coolants are flammable
and may explode, with the risk of injuries. The
use of non-approved coolants or lubricants
may adversely affect system efficiency,
leading to expensive repairs.
80)The air conditioner system contains
coolant under high pressure: to avoid injuries
to people or damage to the system, any
coolant addition or repair that requires to
disconnect the cables must be carried out by
an Alfa Romeo Dealership.LIFTING THE VEHICLE
If the car needs to be jacked up, go to an
Alfa Romeo Dealership which is equipped
with shop jacks or jack arms.
The vehicle lifting points are marked on
the side skirts with the
symbols (see
illustration in fig. 160 ).
16009056S0001EM
176
SERVICING AND CARE

IMPORTANT
81)Keep your speed down when snow chains
are fitted; do not exceed 50 km/h (or the
equivalent in miles). Avoid potholes, do not
drive over steps or pavements and do not
drive long distances over roads without
snow, to avoid damaging both your vehicle
and the road surface.
BODY
PRESERVING THE BODYWORK
Paintwork
82)7)
Touch up abrasions and scratches
immediately to prevent the formation of
rust.
Some parts of the car may be covered
with a matt paint which, in order to be
maintained intact, requires special care:
see the instructions in the warning at the
end of this paragraph.
83)
To correctly wash the vehicle, follow
these instructions:
if high pressure jets or cleaners are
used to wash the vehicle, hold at least
16 in [40 cm] away from the bodywork to
avoid damage or alteration. Build up of
water could cause damage to the car in
the long term;
to make it easier to remove any dirt
deposits in the area where the blades are
normally located it is recommended to
position the windscreen wipers vertically
(service position), for more information
consult the “Maintenance procedures”
paragraph in this chapter.If you want to wash a car with automatic
transmission in a car wash that moves it,
you must do the following:
make sure that the car is on a flat
surface and that automatic engagement
of the parking brake when the engine is
switched off is disabled (for how to
disable it, refer to the “Electric parking
brake” section in the “Starting and
driving” chapter);
with the car stationary, the gear in N
(Neutral) and the brake pedal up: press
the start button.The car will remain in N
(Neutral) for 15 minutes, after which P
(Park) mode will be activated.
IMPORTANT
82)In order to preserve the aesthetic
appearance of the paint abrasive products
and/or polishes should not be used for
cleaning the vehicle.
178
SERVICING AND CARE

2.2 JTD136 HP 150 HP(*)180 HP(*)
CycleDiesel Diesel Diesel
Number and position of cylinders 4 in line 4 in line 4 in line
Piston bore and stroke (mm) 83 / 99 83 / 99 83 / 99
Total displacement (cm³) 2143 2143 2143
Compression ratio 15.5 ± 0.4 15.5 ± 0.4 15.5 ± 0.4
Maximum power (ECE) (kW) 100 110 132
Maximum power (ECE) (HP) 136 150 180
Corresponding engine speed (rpm) 2500 4250 3750
Maximum torque (ECE) (Nm) (manual transmission) 400 380 380
Maximum torque (ECE) (kgm)( manual transmission) 38.75 38.75 38.75
Corresponding engine speed (rpm) (manual transmission) 1500 1500 1500
Maximum torque (ECE) (kgm) (automatic transmission) 450 450 450
Maximum torque (ECE) (kgm) (automatic transmission) 45.89 45.89 45.89
Corresponding engine speed (rpm) 1750 1750 1750
FuelAutomotive diesel fuel (EN590 and EN16734 specifications)
(*) For versions/markets where specified
184
TECHNICAL DATA

2.2 JTD160 HP 190 HP 210 HP
CycleDiesel Diesel Diesel
Number and position of cylinders 4 in line 4 in line 4 in line
Piston bore and stroke (mm) 83 / 99 83 / 99 83 / 99
Total displacement (cm³) 2143 2143 2143
Compression ratio 15.5 ± 0.4 15.5 ± 0.4 15.5 ± 0.4
Maximum power (ECE) (kW) 118 140 155
Maximum power (ECE) (HP) 160 190 210
Corresponding engine speed (rpm) (manual transmission) 3750 3500 –
Corresponding engine speed (rpm) (automatic transmission) 3250 3500 3500
Maximum torque (ECE) (Nm) (manual transmission) 400 400 –
Maximum torque (ECE) (kgm)( manual transmission) 40.7 40.7 –
Corresponding engine speed (rpm) (manual transmission) 1500 1500 –
Maximum torque (ECE) (kgm) (automatic transmission) 450 450 470
Maximum torque (ECE) (kgm) (automatic transmission) 45.89 45.89 47.9
Corresponding engine speed (rpm) 1750 1750 1750
FuelAutomotive diesel fuel (EN590 and EN16734 specifications)
185

WEIGHTS
Weights [lb / kg] 2.0 T4 MAir 2.2 JTD
RWD versions AWD versionsRWD versions(*)RWD versions(**)AWD versions
Unladen weight (with all fluids, fuel tank filled to
90% and without optional equipment)3150/1429 3373/1530 3146/1430 3223/1465 3388/1540
Payload including the driver
(***)1270/576 1268/575 1331/605 1331/605 1353/615
Maximum permitted loads
(**)
– front axle 2028/920 2205/1000 2002/910 2071/940 2244/1020
– rear axle 2506/1137 2557/1160 2541/1155 2543/1156 2557/1160
– total 4420/2005 4641/2105 4477/2035 4554/2070 4741/2155
Maximum combined load (permitted maximum
load + towable weight trailer with brakes)
(***)7931/3605 8151/3705 7997/3635 8074/3670 8261/3755
Towable loads
– braked trailer 3527/1600 3527/1600 3527/1600 3527/1600 3527/1600
– trailer without brakes 1642/745 1642/745 1642/745 1642/745 1642/745
Maximum load on roof 110/50 110/50 110/50 110/50 110/50
Maximum load on tow hitch (trailer with brakes) 141/64 141/64 141/64 141/64 141/64
(*) Manual transmission
(**) Loads not to be exceeded. The user is responsible for arranging goods in the luggage compartment and/or on the load platform within the maximum permitted loads.
(***) If special equipment is fitted (trailer towing equipment, etc.) the empty weight will increase and consequently the payload will decrease in relation to the maximum
permitted loads.
(***) Never exceed the maximum combined vehicle load value: the maximum towable load is only allowed if it does not exceed the maximum combined vehicleload.
191

REFUELLING
86) 87)
2.0 T4 MAir 2.2 JTDPrescribed fuels and original
lubricants
Fuel tank [UK gal (litres)] 12.76 (58) 11.4 (52)Unleaded petrol
(EN228 specifications)
(2.0 T4 MAir engine) / Automotive
diesel fuel (EN590 and
EN16734 specifications)
(2.2 JTD engine) including a reserve of [UK gal
(litres)]1.98 (9.0) 1.76 (8.0)
AdBlue® tank (where provided)
capacity approximately [UK gal
(litres)]– 3.5 / 16.1AdBlue® (DIN 70 070 and ISO
22241-1 specifications)
(2.2 JTD engine)
Primary cooling system (versions
with manual transmission) [UK
gal (litres)]1.89 (8.6) 1.75 (8.0)
50% mixture of distilled water
and PARAFLU UP
(*)Primary cooling system (versions
with automatic transmission) [UK
gal (litres)]1.89 (8.6)1.92 (8.75) (136 HP/160 HP/
190 HP RWD engines) / 1.96 (8.9)
(190 HP/210 HP AWD engines)
Secondary cooling system [UK
gal (litres)]0.95 (4.3)1.16 (5.3) (190 HP/210 HP AWD
automatic transmission engines)
Engine oil filter [UK gal (litres)] 0.13 (0.6) 0.11 (0.5)SELENIA DIGITEK P.E.
(2.0 T4 MAir engine) / SELENIA
W.R. FORWARD 0W-20 (2.2 JTD
engine) (versions with AdBlue®) /
SELENIA W.R. FORWARD 0W-20
(2.2 JTD 150 HP / 180 HP
engines) (versions without
AdBlue®) / SELENIA W.R.
FORWARD 0W-30 (2.2 JTD
210 HP engines) (versions without
AdBlue®) Engine oil sump [UK gal (litres)] 1.01 (4.6)0.68 (3.1) (RWD versions) / 0.85
(3.9) (AWD versions)
(*) When the vehicle is used in particularly harsh weather conditions, we recommend using a 60% mixture of PARAFLU UP and 40% demineralised water.
192
TECHNICAL DATA