2018 YAMAHA YXZ1000R SS torque

8-20
8
TIPA “ ” mark is stamped on the crankcase
near the engine oil drain bolt. 10. Install the engine oil drain bolt with newgasket, the oil tank drain bolt with new
gasket, and then tighten the bolts to the
specified torques. 11. Add 2.00 L (2.11 US qt, 1.76 Imp.qt) of
the recommended engine oil to the oil
tank.
12. Check the O-ring for damage, and re- place it if necessary.1. Engine oil drain bolt
2. Gasket
3. “ ” mark
1 2
3
Tightening torques:Engine oil drain bolt:10 N·m (1.0 kgf·m, 7.4 lb·ft)
Engine oil tank drain bolt: 16 N·m (1.6 kgf·m, 12 lb·ft)
UB0F7AE0.book Page 20 Monday, November 6, 2017 2:30 PM

8-24
8
8. Install the new oil filter cartridge, and thentighten to the specified torque. 9. Follow steps 10–20 of the “To change the
engine oil” section for the oil filling proce-
dure.
10. Slide the front portion of the center bot- tom panel into place as shown, and then
hook the left and right sides of the center
bottom panel into place.1. O-ringTightening torque:Oil filter cartridge:17 N·m (1.7 kgf·m, 13 lb·ft)
1
1. Torque wrench
1
UB0F7AE0.book Page 24 Monday, November 6, 2017 2:30 PM

8-25
8
11. Install the center bottom panel bolts, andthen tighten them to the specified torque.1. Center bottom panel
1. Center bottom panel
1
1
1. Bolt A
2. Bolt B
3. Bolt C
1
2
3
UB0F7AE0.book Page 25 Monday, November 6, 2017 2:30 PM

8-26
8
12. Install the rear bottom panel by installingthe bolts, and then tightening them to the
specified torque. 13. Install the side panel bolts, and then tight-
en them to the specified torque.1. Bolt A
2. Bolt B
3. Bolt CTightening torques:Bolt A:7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt B: 7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt C: 7 N·m (0.7 kgf·m, 5.2 lb·ft)1
3
2
3
1. Rear bottom panel
2. Bolt A
3. Bolt BTightening torques: Bolt A:7 N·m (0.7 kgf·m, 5.2 lb·ft)
Bolt B: 7 N·m (0.7 kgf·m, 5.2 lb·ft)
3
1
2
2
UB0F7AE0.book Page 26 Monday, November 6, 2017 2:30 PM

8-27
8
EBU35107Transmission oilCheck the oil level and change the transmis-
sion oil at the intervals specified in the general
maintenance and lubrication chart.
NOTICEECB02910When checking or changing the transmis-
sion oil, make sure that no foreign material
enters the transmission. If necessary,
clean the filler cap and surrounding area. To check the transmission oil level1. Park the vehicle on a level surface.
2. Remove panel B. (See page 8-11.)
3. Remove the transmission oil filler cap, wipe the dipstick clean, insert it back into
the transmission case (without screwing
it in), and then remove it again.
1. Bolt BTightening torque:Bolt B:7 N·m (0.7 kgf·m, 5.2 lb·ft)
1
1
Recommended oil:YA M A L U B ESAE 5W-30, 10W-30, 10W-40, 15W-40,
20W-40 or 20W-50
Oil quantity: 1.50 L (1.59 US qt, 1.32 Imp.qt)
UB0F7AE0.book Page 27 Monday, November 6, 2017 2:30 PM

8-29
8
TIPOil will flow out immediately when the drain
bolt is loosened. Take care not to lose the
bolt. 4. After draining the oil, install the transmis-sion oil drain bolt with a new gasket.
5. Tighten the drain bolt to the specified torque. 6. Check the O-ring for damage, and re-
place it if necessary.
7. Refill the transmission with the specified amount of the recommended oil.
8. Install the transmission oil filler cap.
9. Start the engine and let it idle while checking for oil leakage.
10. Stop the engine and check the oil level one last time.
EBU36051Final gear oilCheck the oil level and change the final gear
oil at the intervals specified in the general
maintenance and lubrication chart.
1. Transmission oil drain bolt
2. Gasket2
1
Tightening torque:Transmission oil drain bolt:20 N·m (2.0 kgf·m, 15 lb·ft)
UB0F7AE0.book Page 29 Monday, November 6, 2017 2:30 PM

8-30
8
NOTICEECB03590When checking or changing the final gear
oil, make sure that no foreign material en-
ters the final gear case. If necessary, clean
the final gear oil filler bolt and surrounding
area. Checking the final gear oil level1. Park the vehicle on a level surface.
2. Remove the final gear oil filler bolt and its
gasket, and then check the oil level in the
final gear case. The oil level should be at
the brim of the filler hole. 3. If the oil is below the brim of the filler hole,
add sufficient oil of the recommended
type to raise it to the correct level.
4. Check the gasket for damage, and re- place it if necessary.
5. Install the oil filler bolt and its gasket, and
then tighten the bolt to the specified
torque.
Recommended oil:SAE 80 API GL-4 Hypoid gear oil
Oil quantity: 0.47 L (0.50 US qt, 0.41 Imp.qt)
1. Final gear oil
2. Gasket
3. Final gear oil filler bolt
4. Correct oil level
24
3
1
UB0F7AE0.book Page 30 Monday, November 6, 2017 2:30 PM

8-31
8
Changing the final gear oil1. Park the vehicle on a level surface.
2. Place an oil pan under the final gear case
to collect the used oil.
3. Remove the final gear oil filler bolt, the fi-
nal gear oil drain bolt and their gasket to
drain the oil. 4. Install the drain bolt and its new gasket,
and then tighten the bolt to the specified
torque.
5. Refill with the recommended final gear oil up to the brim of the filler hole.
TIPGL-4 is a quality and additive rating; GL-5
rated hypoid gear oils may also be used.
 If desired, an SAE 80W -90 hypoid gear oil
may be used instead. 6. Check the oil filler bolt gasket for dam- age, and replace it if necessary.
7. Install the oil filler bolt and its gasket, and then tighten the bolt to the specified
torque.
Tightening torque:Final gear oil filler bolt:23 N·m (2.3 kgf·m, 17 lb·ft)1. Final gear oil drain bolt
2. Gasket
21
Tightening torque:Final gear oil drain bolt:23 N·m (2.3 kgf·m, 17 lb·ft)
UB0F7AE0.book Page 31 Monday, November 6, 2017 2:30 PM