2018 YAMAHA YXZ1000R SS ABS

4-48
4
3. Tighten the locknut to the specifiedtorque. NOTICE: Always tighten the
locknut against the adjusting nut, and
then tighten it to the specified torque.
[ECB00082]
Crossover setting (YXZ10YESJ)
The crossover setting adjusts the timing when
the shock absorber transitions from the soft
spring to the hard spring.TIP It is recommended to adjust the crossover
setting a similar distance whenever the
spring preload is adjusted.
 The crossover setting is measured from the
bottom of the spring preload adjusting ring
to the bottom of the crossover adjusting
ring.
1. Loosen the crossover locknut as shown.
Tightening torque:
Locknut:41 N·m (4.1 kgf·m, 30 lb·ft)
1. Distance B
2. Crossover locknut
3. Crossover adjusting nut
2
3
1
UB0F7AE0.book Page 48 Monday, November 6, 2017 2:30 PM

4-54
4
YXZ10YEXJ
YXZ10YESJ
WARNING
EWB03500These shock absorber assemblies contain
highly pressurized nitrogen gas. Read and
understand the following information be-
fore handling the shock absorber assem-
blies.
Do not tamper with or attempt to open
the cylinder assemblies.
 Do not subject the shock absorber as-
sembly to an open flame or other high
heat source. This may cause the unit to
explode due to excessive gas pressure.
1. Low speed compression damping force adjusting screw
1. Low speed compression damping force adjusting screw
1
(a)
(b)
1
(a)
(b)
Low speed compression damping setting
Minimum (soft):4 turn(s) out from the fully turned in posi-
tion
Standard: 1 1/2 (YXZ10YEXJ)
2 (YXZ10YESJ) turn(s) out from the fully
turned in position
Maximum (hard): Adjusting screw fully turned in
UB0F7AE0.book Page 54 Monday, November 6, 2017 2:30 PM

4-55
4
Do not deform or damage the cylinders
in any way. Cylinder damage will result in
poor damping performance.
 Do not dispose of a damaged or worn
out shock absorber assembly yourself.
Take the shock absorber assembly to a
Yamaha dealer for any service. EBU35053Auxiliary DC jack
This model has an auxiliary DC jack located at
the left side of the glove compartment. A 12-
V accessory with the proper plug, such as a
radio or smartphone charger, can be used
when the engine is running and the headlights
are off.
1. Start the engine. (See page 6-2.)
2. Turn the headlights off. (See page 4-20.)
3. Open the auxiliary DC jack cap.
4. Turn the accessory off.
5. Insert the accessory power plug.
6. Turn the accessory on.TIP When inserting or removing the accessory
power plug, turn the accessory off.
 When the auxiliary DC jack is not being
used, cover it with the cap.
1. Auxiliary DC jack cap
2. Auxiliary DC jack
2
1
Auxiliary DC jack maximum capacity:
10 A (120 W)
UB0F7AE0.book Page 55 Monday, November 6, 2017 2:30 PM

7-15
7
If you think or feel that the vehicle may tip or
roll, keep your body completely inside the
protective structure of the vehicle:
Brace yourself by pressing your feet firmly
on the floorboard and keep a firm grip on
the steering wheel or passenger handhold.
 Do not put your hands or feet outside of the
vehicle for any reason. Do not try to stop a
tipover using your arm or leg.
Accelerating
Avoid higher speeds and sudden or hard ac-
celeration until you are thoroughly familiar
with the operation of your vehicle. Avoid sud-
den or hard acceleration in any turn. Never
drive faster than is safe for current conditions.
Shifting
Follow the instructions on pages 6-2 and 6-3
for shifting, downshifting, and shifting into re-
verse until you are thoroughly familiar with
each operation. Braking
When slowing down or stopping, take your
foot off the accelerator pedal and press the
brake pedal smoothly. Abrupt or improper
use of the brakes can cause the tires to lose
traction, reducing control of the vehicle and
increasing the possibility of an accident.
Braking ability is affected by type of terrain. In
most cases, gradual application of the brakes
is more effective than abrupt braking, partic-
ularly on loose surfaces
, such as gravel. Al-
ways allow for greater braking distance on
rough, loose, or slippery surfaces.
Engine compression braking will also help
slow the vehicle down. With the transmission
still in gear, take your foot off the accelerator
and allow the drivetrain and engine to absorb
vehicle speed. Downshift as necessary. Ap-
plication of the brakes provides additional
stopping power.UB0F7AE0.book Page 15 Monday, November 6, 2017 2:30 PM

9-1
9
EBU32720
CLEANING AND STORAGE
EBU35920CleaningFrequent, thorough cleaning of your vehicle
will not only enhance its appearance but will
improve its general performance and extend
the useful life of many components.1. Before cleaning the vehicle: a. Block off the end of the exhaust pipeto prevent water entry. A plastic bag
and strong rubber band may be used.
b. Make sure the spark plugs and all filler caps are properly installed.
2. If the engine case is excessively greasy, apply degreaser with a paint brush. Do
not apply degreaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden hose. Use only enough pressure
to do the job. WARNING! Test the
brakes after washing. Apply the
brakes several times at slow speeds to
let friction dry the brakes. Wet brakes may have reduced stopping ability, in-
creasing the chance of an accident.
[EWB03471]

NOTICE: Excessive water pres-
sure may cause water seepage and
deterioration of wheel bearings,
brakes, transmission seals and electri-
cal devices. Many expensive repair
bills have resulted from improper high-
pressure detergent applications such
as those available in coin-operated car
washers.
[ECB00712]
4. Once the majority of the dirt has been hosed off, wash all surfaces with warm
water and mild, detergent-type soap. An
old toothbrush or bottle brush is handy
for hard-to-get-at places.
5. Rinse the vehicle off immediately with
clean water and dry all surfaces with a
clean chamois towel or soft, absorbent
cloth.
6. Clean the seats with a vinyl upholstery cleaner to keep the covers pliable and
glossy.
UB0F7AE0.book Page 1 Monday, November 6, 2017 2:30 PM

10-4
10
Loading:Maximum loading limit:317.0 kg (699 lb)
(Total weight of operator, passenger, cargo, and
accessories)Tire air pressure (measured on cold tires):Recommended: Vehicle load:0 - 195 kg (0 - 430 lb)
Front: 114.0 kPa (1.140 kgf/cm², 16.5 psi)
Rear:
128.0 kPa (1.280 kgf/cm², 18.5 psi)
Vehicle load: 195 kg - maximum (430 lb - maximum)
Front: 114.0 kPa (1.140 kgf/cm², 16.5 psi)
Rear:
169.0 kPa (1.690 kgf/cm², 24.5 psi)
Minimum: Vehicle load:
0 - 195 kg (0 - 430 lb)
Front: 110.0 kPa (1.100 kgf/cm², 16.0 psi)
Rear: 124.0 kPa (1.240 kgf/cm², 18.0 psi)
Vehicle load:
195 kg - maximum (430 lb - maximum)
Front: 110.0 kPa (1.100 kgf/cm², 16.0 psi)
Rear: 165.0 kPa (1.650 kgf/cm², 24.0 psi)
Front wheel:Wheel type:Cast wheel
Rim size:
14 x 6.5ATRear wheel:Wheel type:Cast wheel
Rim size:
14 x 8.0ATFront brake:Type:Hydraulic disc brake
Specified brake fluid:
DOT 4Rear brake:Type:Hydraulic disc brake
Specified brake fluid:
DOT 4Front suspension:Type:Double wishbone
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel: 410 mm (16.2 in)Rear suspension:Type:
Double wishbone
UB0F7AE0.book Page 4 Monday, November 6, 2017 2:30 PM

10-5
10
Spring/shock absorber type:Coil spring/gas-oil damper
Wheel travel: 432 mm (17.0 in)Electrical system:Ignition system:TCI
Charging system: AC magnetoBattery:Model:U1-H11L
Voltage, capacity: 12 V, 28.0 AhBulb voltage, wattage × quantity:Headlight:
LED
Interior light: LED (for equipped models)
Tail/brake light:
LED
Neutral indicator light: LED
High beam indicator light: LED
Reverse indicator light:
LED
Coolant temperature warning light: LED
Engine trouble warning light: LED Parking brake indicator light:
LED
Differential gear lock indicator light: LED
EPS warning light:
LED
Helmet/Seat belt indicator light: 14 V, 0.85 W × 2
Shift timing indicator light: LED
Half clutch indicator light:
LED
Launch system indicator light: LED
YCC-S system warning light: LED
Fuses:Main fuse:50.0 A
Fuel injection system fuse: 15.0 A
EPS fuse:
40.0 A
Headlight fuse: 15.0 A
Signaling system fuse: 10.0 A
Ignition fuse:
15.0 A
Auxiliary DC jack fuse: 10.0 A
UB0F7AE0.book Page 5 Monday, November 6, 2017 2:30 PM

12-2
12
HHalf clutch indicator light ............................................... 4-6
Headlight beam, adjusting ........................................... 8-65
Headlights .................................................................... 8-65
Helmet indicator light ..................................................... 4-9
High beam indicator light ............................................... 4-3
Hood ............................................................................ 8-11IIdentification number records ...................................... 11-1
Indicator lights and warning lights ................................. 4-2
Instruments, lights and switches, Pre-operation check ........................................................................... 5-8
Interior lights (for equipped models) ............................ 8-66
Interior light switch (for equipped models) .................. 4-20JJump-starting .............................................................. 8-61LLabel locations ............................................................... 1-1
Launch system indicator light ........................................ 4-7
Launch system operation .............................................. 6-7
Light switch .................................................................. 4-20
Loading ........................................................................ 6-12MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................ 8-6
Maintenance chart, emission control system ................ 8-4
Maintenance charts ....................................................... 8-4
Model label .................................................................. 11-1
Multi-function meter unit ............................................. 4-10NNeutral indicator light ..................................................... 4-2
OOwner’s Manual and tool kit .......................................... 8-2PPanels .......................................................................... 8-11
Parking ......................................................................... 6-12
Parking brake indicator light .......................................... 4-3
Parking brake lever ...................................................... 4-23
Parking brake lever free play, adjusting ...................... 8-50
Parking brake pads, checking ..................................... 8-46
Passenger handhold, Pre-operation check ................... 5-7
Pedal, lubrication ......................................................... 8-52RRear knuckle upper and lower pivot, lubrication ......... 8-54
Rearview mirror (for equipped models) ....................... 4-29
Reverse indicator light ................................................... 4-2SSafety information .......................................................... 2-1
Seat belt indicator light .................................................. 4-9
Seat belts ..................................................................... 4-29
Seat belts, Pre-operation check .................................... 5-7
Seats ............................................................................ 4-26
Shifting and reverse driving ........................................... 6-3
Shift timing indicator light .............................................. 4-4
Shock absorbers, front ................................................ 4-34
Shock absorbers, rear ................................................. 4-44
Spark arrester, cleaning ............................................... 8-43
Spark plugs, checking ................................................. 8-37
Specifications .............................................................. 10-1
Stabilizer bushes, checking .......... ............................... 8-52
Starting the engine ........................................................ 6-2
Steering, Pre-operation check ....................................... 5-7
UB0F7AE0.book Page 2 Monday, November 6, 2017 2:30 PM