2018 YAMAHA MT-03 turn signal bulb

Table of contents
Replacing a turn
signal light bulb ......................... 6-34
Replacing the license plate light bulb .......................... 6-34
Supporting the motorcycle ........... 6-35
Troubleshooting............................ 6-36
Troubleshooting charts................. 6-37
Motorcycle care an d stora ge.......... 7-1
Matte color caution ........................ 7-1
Care ................................................ 7-1
Storage ........................................... 7-4
Specifications ................................... 8-1
Consumer information ..................... 9-1
Identification numbers .................... 9-1
Diagnostic connector ..................... 9-2
Vehicle data recording.................... 9-3
In dex ................................................ 10-1
UB9AE0E0.book Page 2 Thursday, March 23, 2017 2:48 PM

Instrument and control functions
3-12
3
TIP
When the switch is set to low beam,
only the right headlight bulb comes on.
When the switch is set to high beam,
both headlight bulbs come on.
EAU12461Turn si gnal switch “ / ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When
released, the switch returns to the cen-
ter position. To cancel the turn signal
lights, push the switch in after it has re-
turned to the center position.
EAU12501Horn switch “ ”
Press this switch to sound the horn.
EAU12662En gine stop switch “ / ”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12713Start switch “ ”
Push this switch to crank the engine
with the starter. See page 5-2 for start-
ing instructions prior to starting the en-
gine.
EAU62500The engine trouble warning light will
come on when the key is turned to “ ”
and the start switch is pushed, but this
does not indicate a malfunction.
EAU12822
Clutch lever
The clutch lever is located on the left
side of the handlebar. To disengage
the clutch, pull the lever toward the
handlebar grip. To engage the clutch,
release the lever. The lever should be
pulled rapidly and released slowly for
smooth clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
3-23.)
1. Clutch lever
1
UB9AE0E0.book Page 12 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-32
6 3. Turn the key to “ ” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
EAU68470
Replacin g the hea dlig ht bul b
This model is equipped with halogen
bulb headlight. If a headlight bulb
burns out, have a Yamaha dealer re-
place it and, if necessary, adjust the
headlight beam.
NOTICE
ECA17871
Hea dlig ht lens:
Do not affix any type of tinted film or
stickers to the head light lens.
Do not use a hea dlig ht bul b of a
wattag e higher than specified .
Specified fuses:
Main fuse: 30.0 A
Headlight fuse:
15.0 A
Signaling system fuse: 7.5 A
Ignition fuse: 15.0 A
Radiator fan motor fuse:
7.5 A
ABS motor fuse: 30.0 A
ABS solenoid fuse: 15.0 A
ABS control unit fuse:
7.5 A
Backup fuse: 7.5 A
UB9AE0E0.book Page 32 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-34
6
EAU62590
Replacin g a turn si gnal li ght
b ul b
1. Remove the turn signal light lens
by removing the screw.
2. Remove the turn signal light bulb socket (together with the bulb) by
turning it counterclockwise.
3. Remove the burnt-out bulb by pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with the bulb) by turning it clockwise.
6. Install the turn signal light lens by installing the screw. NOTICE: Do
not overti ghten the screw, oth-
erwise the lens may b reak.
[ECA11192] EAU62670
Replacin
g the license plate
li g ht bul b
1. Remove the mudguard by remov-
ing the quick fasteners.
2. Remove the rear fender lower panel by removing the bolts and
screws.
3. Remove the license plate light bulb socket (together with the
bulb) by pulling it out.
4. Remove the burnt-out bulb by pulling it out.
1. Turn signal light lens
2. Screw
1. Turn signal light bulb socket
1
2
1
1. Mudguard
2. Quick fastener
1. Bolt
2. Screw
3. Rear fender lower panel
1
2
3
2
1
2
2
1
UB9AE0E0.book Page 34 Thursday, March 23, 2017 2:48 PM

Specifications
8-3
8
Bulb watta ge:
Headlight:
H4, 60.0 W/55.0 W
Brake/tail light:
LED
Front turn signal light: 10.0 W
Rear turn signal light: 10.0 W
Auxiliary light:
LED
Meter lighting: LED
Neutral indicator light: LED
High beam indicator light: LED
Oil pressure warning light:
LED
Turn signal indicator light: LED
Engine trouble warning light: LED
ABS warning light:
LED
Fuse(s):
Main fuse:30.0 A
Headlight fuse:
15.0 A
Signaling system fuse: 7.5 A
Ignition fuse: 15.0 A
Radiator fan motor fuse:
7.5 A
ABS control unit fuse: 7.5 A
ABS motor fuse: 30.0 A
ABS solenoid fuse:
15.0 A
Backup fuse: 7.5 A
UB9AE0E0.book Page 3 Thursday, March 23, 2017 2:48 PM

Index
10-2
10
Troubleshooting ................................... 6-36
Troubleshooting charts ........................ 6-37
Turn signal indicator light ....................... 3-2
Turn signal light bulb, replacing ........... 6-34
Turn signal switch ................................ 3-12
V
Valve clearance .................................... 6-15
Vehicle identification number ................. 9-1
W
Wheel bearings, checking .................... 6-28
Wheels.................................................. 6-17
UB9AE0E0.book Page 2 Thursday, March 23, 2017 2:48 PM