2018 YAMAHA MT-03 ABS

Operation and important rid ing points
5-2
5
EAU67610
Startin g the en gine
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:
z The transmission is in the neutral
position.
z The transmission is in gear with
the clutch lever pulled and the
sidestand up.
See page 3-23 for more informa-
tion.
1. Turn the key to “ ” and make sure that the engine stop switch is
set to “ ”.
The engine trouble warning light
should come on for a few sec-
onds, then go off. NOTICE: If the
warnin g lig ht does not go off,
have a Yamaha dealer check its
electrical circuit.
[ECAT1121]
The ABS warning light should
come on when the main switch is
turned to “ON” and then go off af-
ter traveling at a speed 10 km/h (6
mi/h) or higher.
NOTICE
ECA17682
If the ABS warnin g lig ht does not
come on an d then g o off as ex-
plaine d a bove, see pa ge 3-2 for the
warnin g lig ht circuit check.
2. Shift the transmission into the
neutral position. The neutral indi-
cator light should come on. If not,
ask a Yamaha dealer to check the
electrical circuit.
3. Start the engine by pushing the start switch.
If the engine fails to start, release
the start switch, wait a few sec-
onds, and then try again. Each starting attempt should be as
short as possible to preserve the
battery. Do not crank the engine
more than 10 seconds on any one
attempt.
NOTICE
ECA11043
For maximum en
gine life, never ac-
celerate har d when the en gine is
col d!
UB9AE0E0.book Page 2 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-21
6
EAU40262
Checkin g the brake flui d level
Before riding, check that the brake fluid
is above the minimum level mark.
Check the brake fluid level with the top
of the reservoir level. Replenish the
brake fluid if necessary.
Front brake
Rear brake
WARNING
EWA16011
Improper maintenance can result in
loss of brakin g a bility. O bserve
these precautions: z Insufficient brake flui d may al-
low air to enter the brake sys-
tem, re ducing brakin g
performance. z
Clean the filler cap before re-
moving . Use only DOT 4 b rake
flui d from a seale d container.
z Use only the specifie d b rake flu-
i d ; otherwise, the ru bber seals
may deteriorate, causin g leak-
a g e.
z Refill with the same type of
brake flui d. A ddin g a brake flui d
other than DOT 4 may result in a
harmful chemical reaction.
z Be careful that water or dust
d oes not enter the brake flui d
reservoir when refilling . Water
will si gnificantly lower the boil-
in g point of the flui d an d may re-
sult in vapor lock, an d d ir
t may
clo g the ABS hy draulic unit
valves.
NOTICE
ECA17641
Brake flui d may d amage painte d
surfaces or plastic parts. Always
clean up spille d flui d imme diately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indi-
cate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
fluid level goes down suddenly, have a
Yamaha dealer check the cause before further riding.
1. Minimum level mark
1. Minimum level mark
Specified b rake flui d:
DOT 4
1
1
UB9AE0E0.book Page 21 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-31
6
5. Place the tray in its original posi-
tion, and then install the quick fas-
teners.
6. Install the passenger seat.
Fuse box 1 is located behind the center
cover. (See page 3-18.)
Fuse box 1
Fuse box 2 is located under the rider
seat. (See page 3-18.) Fuse
box 2
If a fuse is blown, replace it as follows. 1. Turn the key to “ ” and turn off the electrical circuit in question.
2. Remove the blown fuse, and then install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a hi gher ampera ge
ratin g than recommen ded to
avoi d causin g extensive dam-
a g e to the electrical system an d
possi bly a fire.
[EWA15132]
1. Fuse box 1
1. Ignition fuse
2. Signaling system fuse
3. ABS control unit fuse
4. Backup fuse (for clock)
5. Headlight fuse
6. Radiator fan motor fuse
7. Spare fuse
1
71
2
3
5
6
4
1. Fuse box 2
1. Spare fuse
2. ABS solenoid fuse
3. ABS motor fuse
1
123
UB9AE0E0.book Page 31 Thursday, March 23, 2017 2:48 PM

Periodic maintenance an d a djustment
6-32
6 3. Turn the key to “ ” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows again, have a Yamaha dealer
check the electrical system.
EAU68470
Replacin g the hea dlig ht bul b
This model is equipped with halogen
bulb headlight. If a headlight bulb
burns out, have a Yamaha dealer re-
place it and, if necessary, adjust the
headlight beam.
NOTICE
ECA17871
Hea dlig ht lens:
Do not affix any type of tinted film or
stickers to the head light lens.
Do not use a hea dlig ht bul b of a
wattag e higher than specified .
Specified fuses:
Main fuse: 30.0 A
Headlight fuse:
15.0 A
Signaling system fuse: 7.5 A
Ignition fuse: 15.0 A
Radiator fan motor fuse:
7.5 A
ABS motor fuse: 30.0 A
ABS solenoid fuse: 15.0 A
ABS control unit fuse:
7.5 A
Backup fuse: 7.5 A
UB9AE0E0.book Page 32 Thursday, March 23, 2017 2:48 PM

Motorcycle care and stora ge
7-3
7
2. Apply a corrosion protection spray
on all metal, including chrome-
and nickel-plated, surfaces to pre-
vent corrosion.
Cleaning the windshield
Avoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield
with a cloth or sponge dampened with
a mild detergent, and then wash it off
thoroughly with water. For additional
cleaning, use Yamaha Windshield
Cleaner or another high-quality wind-
shield cleaner. Some cleaning com-
pounds for plastics may leave
scratches on the windshield. Before
using such cleaners, test an area of the
windshield which does not affect your
visibility and which cannot be easily
recognized.
After cleaning 1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
4. To prevent corrosion, it is recom- mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
5. Use spray oil as a universal clean- er to remove any remaining dirt. 6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.WARNING
EWA11132
Contaminants on the b rakes or tires
can cause loss of control. z Make sure that there is no oil or
wax on the brakes or tires.
z If necessary, clean the brake
d iscs an d b rake linin gs with a
re gular brake disc cleaner or
acetone, an d wash the tires with
warm water an d a mil d d eter-
g ent. Before ri din g at hi gher
speed s, test the motorcycle’s
b rakin g performance an d cor-
nering b ehavior.
NOTICE
ECA10801
z Apply spray oil an d wax spar-
in gly an d make sure to wipe off
any excess.
z Never apply oil or wax to any
rubber an d plastic parts, b ut
treat them with a suita ble care
prod uct.
z Avoi d using abrasive polishin g
compoun ds as they will wear
away the paint.
TIP
z Consult a Yamaha dealer for ad-
vice on what products to use.
z Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
UB9AE0E0.book Page 3 Thursday, March 23, 2017 2:48 PM

Specifications
8-2
8
4th:1.087 (25/23)
5th: 0.920 (23/25)
6th:
0.800 (24/30)
Chassis:
Frame type:Diamond
Caster angle:
25.0 °
Trail: 95 mm (3.7 in)
Front tire:
Type:Tubeless
Size:
110/70-17M/C (54H)
Manufacturer/model: MICHELIN/PILOT STREET
Rear tire:
Type:
Tubeless
Size: 140/70-17M/C (66H)
Manufacturer/model: MICHELIN/PILOT STREET
Loa din g:
Maximum load:
160 kg (353 lb)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measure d on col d
tires):
Up to 90 kg (198 lb) load:
Front: 200 kPa (2.00 kgf/cm², 29 psi)
Rear: 250 kPa (2.50 kgf/cm², 36 psi)
90 kg (198 lb) load - maximum load:
Front: 200 kPa (2.00 kgf/cm², 29 psi)
Rear:
250 kPa (2.50 kgf/cm², 36 psi)
Front wheel:
Wheel type:Cast wheel
Rim size:
17M/C x MT2.75
Rear wheel:
Wheel type: Cast wheel
Rim size:
17M/C x MT4.00
Front brake:
Type:
Hydraulic single disc brake
Specified brake fluid:
DOT 4
Rear brake:
Type:
Hydraulic single disc brake
Specified brake fluid:
DOT 4
Front suspension:
Type:Telescopic fork
Spring: Coil spring
Shock absorber:
Hydraulic damper
Wheel travel: 130 mm (5.1 in)
Rear suspension:
Type:
Swingarm
Spring: Coil spring
Shock absorber: Hydraulic damper
Wheel travel:
125 mm (4.9 in)
Electrical system:
System voltage:12 V
Ignition system:
TCI
Charging system: AC magneto
Battery:
Model:
GTZ8V
Voltage, capacity: 12 V, 7.0 Ah (10 HR)
Hea dlig ht:
Bulb type:
Halogen bulb
UB9AE0E0.book Page 2 Thursday, March 23, 2017 2:48 PM

Specifications
8-3
8
Bulb watta ge:
Headlight:
H4, 60.0 W/55.0 W
Brake/tail light:
LED
Front turn signal light: 10.0 W
Rear turn signal light: 10.0 W
Auxiliary light:
LED
Meter lighting: LED
Neutral indicator light: LED
High beam indicator light: LED
Oil pressure warning light:
LED
Turn signal indicator light: LED
Engine trouble warning light: LED
ABS warning light:
LED
Fuse(s):
Main fuse:30.0 A
Headlight fuse:
15.0 A
Signaling system fuse: 7.5 A
Ignition fuse: 15.0 A
Radiator fan motor fuse:
7.5 A
ABS control unit fuse: 7.5 A
ABS motor fuse: 30.0 A
ABS solenoid fuse:
15.0 A
Backup fuse: 7.5 A
UB9AE0E0.book Page 3 Thursday, March 23, 2017 2:48 PM

10-1
10
Index
A
ABS ....................................................... 3-14
ABS warning light ................................... 3-3
Air filter element and check hose,
replacing and cleaning ....................... 6-13
Auxiliary light......................................... 6-33
B
Battery .................................................. 6-29
Brake and clutch levers, checking
and lubricating .................................... 6-26
Brake and shift pedals, checking and lubricating .................................... 6-25
Brake fluid, changing ............................ 6-22
Brake fluid level, checking .................... 6-21
Brake lever ............................................ 3-13
Brake lever free play, checking............. 6-19
Brake light switches.............................. 6-19
Brake pedal........................................... 3-14
C
Cables, checking and lubricating ......... 6-24
Canister................................................... 6-8
Care ........................................................ 7-1
Catalytic converter ................................ 3-18
Clutch lever ........................................... 3-12
Clutch lever free play, adjusting ........... 6-18
Coolant ................................................. 6-11
D
Data recording, vehicle ........................... 9-3
Diagnostic connector.............................. 9-2
Dimmer switch ...................................... 3-11
Drive chain, cleaning and lubricating .... 6-24
Drive chain slack................................... 6-22
E
Engine break-in....................................... 5-4
Engine oil and oil filter cartridge ............. 6-8
Engine serial number .............................. 9-1
Engine stop switch ............................... 3-12
Engine trouble warning light ................... 3-3
F
Front and rear brake pads, checking.... 6-20
Front fork, checking .............................. 6-27
Fuel ....................................................... 3-16
Fuel tank cap ........................................ 3-15
Fuel tank overflow hose ........................ 3-17
Fuses, replacing.................................... 6-30
H
Handlebar switches .............................. 3-11
Headlight bulb, replacing ...................... 6-32
Helmet holders...................................... 3-20
High beam indicator light........................ 3-2 Horn switch .......................................... 3-12
I
Identification numbers ............................ 9-1
Ignition circuit cut-off system............... 3-23
Indicator lights and warning lights ......... 3-2
L
License plate light bulb, replacing........ 6-34
Luggage strap holders ......................... 3-22
M
Main switch/steering lock....................... 3-1
Maintenance and lubrication, periodic ... 6-4
Maintenance, emission
control system ..................................... 6-3
Matte color, caution ............................... 7-1
Model label ............................................. 9-1
Multi-function meter unit ........................ 3-4
N
Neutral indicator light ............................. 3-2
O
Oil pressure warning light ....................... 3-2
P
Parking ................................................... 5-4
Part locations ......................................... 2-1
Pass switch .......................................... 3-11
S
Safety information .................................. 1-1
Seats .................................................... 3-18
Shifting ................................................... 5-3
Shift pedal ............................................ 3-13
Shift timing indicator light....................... 3-4
Shock absorber assembly, adjusting............................................. 3-21
Sidestand ............................................. 3-23
Sidestand, checking and lubricating .... 6-26
Spark plugs, checking ............................ 6-7
Specifications ......................................... 8-1
Starting the engine ................................. 5-2
Start switch .......................................... 3-12
Steering, checking................................ 6-28
Storage ................................................... 7-4
Storage compartment .......................... 3-21
Supporting the motorcycle................... 6-35
Swingarm pivots, lubricating ................ 6-27
T
Tail/brake light ...................................... 6-33
Throttle grip and cable, checking and lubricating .................... 6-25
Throttle grip free play, checking........... 6-14
Tires ...................................................... 6-15
Tool kit.................................................... 6-2
UB9AE0E0.book Page 1 Thursday, March 23, 2017 2:48 PM