2018 VOLVO XC90 TWIN ENGINE trip computer

DISPLAYS AND VOICE CONTROL
92Displaying trip statistics in the
center display
Trip computer statistics can be displayed graphi-
cally in the center display, providing an overview
that facilitates more fuel-efficient driving.
Open the Driver performance
app in the App view to display
trip statistics.
Each bar in the graph repre-
sents a driving distance of 1
kilometers, 10 kilometers or
100 kilometers (or miles). The bars are added
from the right as you drive. The bar at the far right
shows the data for the current trip.
Average fuel consumption and total driving time
are calculated from the most recent reset of the
trip statistics.
Fuel and electricity consumption are shown in
separate graphs. The electricity consumption
shows "net" consumption, i.e. consumed current
minus regenerated current generated by braking. Trip computer statistics
2
.
Related information
• Trip statistics settings (p. 92)
• Trip computer (p. 89) Trip statistics settings
Trip statistics settings can be reset or adjusted.
1. Open the Driver performance app in the
App view to display trip statistics. 2.
Tap Preferences to
• change the graph scale. Select 1, 10 or
100 km/miles for the bar.
• reset data after each trip. Performed when
the vehicle remains stationary for more
than 4 hours.
• reset data for current trip.
Trip statistics, calculated average consump-
tion, and total driving time are always reset
simultaneously.
Unit standards for distance, speed, etc. can be
changed via system settings in the center display. 2
The illustration is generic - details may vary according to vehicle mode\
l.

DISPLAYS AND VOICE CONTROL
93
Related information
•Displaying trip statistics in the center display
(p. 92)
• Trip computer (p. 89)
• Resetting the trip odometer (p. 91) Date and time
The clock is displayed in both the instrument
panel and the center display.
Location of clock Location of clock in 12" and 8" instrument panels.
In the center display, the clock is located at the
top right of the status bar.
Certain messages and other information may
obscure the clock in the instrument panel.
Time and date settings
– Select Settings System Date and
Time in the center display's Top view to
change settings for time and date format.
Adjust the time and date by tapping the up or
down arrows on the touchscreen.
Automatic time for vehicles with GPS
When the vehicle is equipped with a navigation
system, Auto Time is also available. The time
zone will then be automatically set to the vehi-
cle's location. In some navigation systems, the
current location must also be set to determine
the correct time zone. If Auto Time is not selected, the time and date can be adjusted
using the up and down arrows on the
touchscreen.
Daylight savings time
In some countries, an automatic change to day-
light savings time can be selected by activating
Auto. For other countries, daylight savings time
can be changed by selecting On or
Off.
Related information
• Instrument panel (p. 84)
• Changing settings in the center display
(p. 134)

MAINTENANCE AND SERVICE
}}
599
Periodic maintenance helps minimize
emissions
NOTE •
Refer to your Service and Warranty Book-
let for a comprehensive service and main-
tenance schedule up to 240,000 km
(150,000 miles). This program contains
inspections and services necessary for
the proper function of your vehicle and
includes components that affect vehicle
emissions.
• The Warranty and Service Records Infor-
mation booklet also contains detailed
information concerning the warranties
that apply to your vehicle.
On-board Diagnostic SystemOBD II is part of your vehicle's computerized
engine management system. It stores diagnostic
information about your vehicle's emission con-
trols. It can light the Check Engine light (MIL) if it
detects an emission control "fault." A "fault" is a
component or system that is not performing
within an expected range. A fault may be perma-
nent or temporary. OBD II will store a message
about any fault.
Emission inspection readiness
How do states use OBD II for emission
inspections?
Many states connect a computer directly to a
vehicle's OBD II system. The inspector can then
read "faults." In some states, this type of inspec-
tion has replaced the tailpipe emission test.
How can my vehicle fail OBD II emission
inspection?
Your vehicle can fail OBD II emission inspection
for any of the following reasons:
• If your Check Engine (MIL) light is lit, your
vehicle may fail inspection.
• If your vehicle's Check Engine light was lit,
but went out without any action on your part,
OBD II will still have a recorded fault. Your
vehicle may pass or fail, depending on the
inspection practices in your area.
• If you had recent service that required dis-
connecting the battery, OBD II diagnostic
information may be incomplete and "not
ready" for inspection. A vehicle that is not
ready may fail inspection.
How can I prepare for my next
OBD II
emission inspection?
• If your Check Engine (MIL) light is lit - or was
lit but went out without service, have your vehicle diagnosed and, if necessary, serviced
by a qualified Volvo technician.
• If you recently had service for a lit Check
Engine light, or if you had service that
required disconnecting the battery, a period
of driving is necessary to bring the OBD II
system to "ready" for inspection. Two half-
hour trips of mixed stop-and-go/highway
driving are typically needed to allow OBD II to
reach readiness. Your Volvo retailer can pro-
vide you with more information on planning a
trip.
• Maintain your vehicle in accordance with your
vehicle's maintenance schedule.
Owner maintenancePeriodic maintenance requirements and intervals
are described in your vehicle's Warranty and
Service Records Information booklet.
The following points can be carried out between
the normally scheduled maintenance services.
Each time the car is refueled:
•Check the engine oil level.
• Clean the windshield, windshield wipers,
headlights, and taillights.

INDEX
679
removal 566
rotation 551
specifications 554, 665
storage 550
tire pressure monitoring 559
tire sealing 572
Tread depth 571
tread wear indicator 553
winter tires 571
Tire sealing system 573
Tire tread 553
Tools 564
Top tether anchors (child restraint sys-
tems) 72
Total airing function 239, 257
Towbar 471 removable, attaching, installing, mount-
ing 471
removable, removing, detaching 471
Towing 476
Towing capacity and towball load 660
Towing eyelet 476
TPMS - Tire Pressure Monitoring System 559
Traction control 274
Traffic information 493
Trailer 474 driving with a trailer 472 Lamps
475
swaying
474
Trailer Stability Assist 474
trailer 474
Trailer stabilizer 274
Trailer towing trailer hitch 471
Transmission 438
automatic 439
Transmission fluid grade 663
Travel Link 502
Fuel 505
Notifications 504
Sports 506
weather 503
Tread depth 553, 571
Tread wear indicator 553
Trip computer 89, 90
Trip odometer 89
Trip odometer resetting 91
Trip statistics 92
Troubleshooting Adaptive Cruise Control 307
Troubleshooting the camera sensor 332
TSA - Trailer Stability Assist 274, 474 Tunnel detection
155
Turn off engine 426
Turn signals 158
Twin Engine general 406
Type approval radar system 330
U Uniform Tire Quality Grading
556
Units
132
Unknown vehicle component 270
Unlocking settings 242
with key blade 251
USB socket for connecting media 514
V Vehicle care 638, 639, 641, 642, 643, 644
leather upholstery
636
Vehicle Event Data 33
Vehicle functions in the center display 122