2018 Ram ProMaster City instrument cluster

INSTRUMENT PANEL
Instrument Panel
1 — Air Vents4 — Windshield Wiper Lever
2 — Multifunction Lever 5 — Radio
3 — Instrument Cluster 6 — Steering Wheel
10 GRAPHICAL TABLE OF CONTENTS

Front Fog Lights — If Equipped
The fog light switch is located on the center stack
of the instrument panel, just below the radio.
Push the switch once to turn the front fog lights
on. Push the switch a second time to turn the front fog
lights off.
Turn Signals
Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show proper
operation of the front and rear turn signal lights.
NOTE: If either light remains on and does not flash, or
there is a very fast flash rate, check for a defective outside
light bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is defec-
tive.
Lane Change Assist
Tap the lever up or down once, without moving beyond
the detent, and the turn signal (right or left) will flash five
times then automatically turn off.
INTERIOR LIGHTS
Courtesy/Interior Lights
These lights are mounted between the sun visors on the
overhead console. Each light is turned on by pushing the
corresponding switch.
Left Switch
• Push the left switch to the left to turn off the auto dome
lights. The dome lights will not automatically turn on
when a door is opened.
• Push the left switch to the right to turn on the dome
lights.
3
GETTING TO KNOW YOUR VEHICLE 43

GETTING TO KNOW YOUR INSTRUMENT PANEL
CONTENTS
INSTRUMENT CLUSTER ...................72
▫ Instrument Cluster Descriptions .............72
 INSTRUMENT CLUSTER DISPLAY ............73
▫ Location And Controls ...................74
▫ Change Engine Oil — If Equipped ...........76
▫ Instrument Cluster Display Menu Items ........76
 TRIP COMPUTER .........................81
▫ Trip Button ............................81
▫ Trip Functions .........................82
▫ Values Displayed .......................82
 WARNING LIGHTS AND MESSAGES ..........83▫
Red Warning Lights ......................83
▫ Yellow Warning Lights ....................87
▫ Yellow Indicator Lights ...................91
▫ Green Indicator Lights ....................91
▫ Blue Indicator Lights .....................92
 ONBOARD DIAGNOSTIC SYSTEM — OBD II ....92
▫ Onboard Diagnostic System (OBD II)
Cybersecurity ..........................92
 EMISSIONS INSPECTION AND MAINTENANCE
PROGRAMS ............................934

INSTRUMENT CLUSTER
Instrument Cluster Descriptions
1. Speedometer•Indicates vehicle speed. 2. Fuel Gauge
•The pointer shows the level of fuel in the fuel tank
when the ignition switch is in the ON/RUN position.
•
The fuel pump arrow symbol points to the side
of the vehicle where the fuel door is located.
Instrument Cluster
72 GETTING TO KNOW YOUR INSTRUMENT PANEL

3. Temperature Gauge•The temperature gauge shows engine coolant tem-
perature. Any reading within the normal range indi-
cates that the engine cooling system is operating
satisfactorily.
• The gauge pointer will likely indicate a higher tem-
perature when driving in hot weather or up mountain
grades. It should not be allowed to exceed the upper
limits of the normal operating range.
WARNING!
A hot engine cooling system is dangerous. You or
others could be badly burned by steam or boiling
coolant. You may want to call an authorized dealer for
service if your vehicle overheats. If you decide to look
under the hood yourself, see “Servicing And Mainte-
nance.” Follow the warnings under the Cooling System
Pressure Cap paragraph.
CAUTION!
Driving with a hot engine cooling system could dam-
age your vehicle. If the temperature gauge reads “H,”
(Continued)
CAUTION! (Continued)
pull over and stop the vehicle. Idle the vehicle with the
air conditioner turned off until the pointer drops back
into the normal range. If the pointer remains on the
“H,” turn the engine off immediately and call an
authorized dealer for service.
4. Tachometer •Indicates the engine speed in revolutions per minute
(RPM x 1000).
5. Instrument Cluster Display •When the appropriate conditions exist, this display
shows the instrument cluster display messages. Refer
to “Instrument Cluster Display” in “Getting To Know
Your Instrument Panel” for further information.
INSTRUMENT CLUSTER DISPLAY
Your vehicle may be equipped with an instrument cluster
display, which offers useful information to the driver. With
the ignition in the STOP/OFF mode, opening/closing of a
door will activate the display for viewing, and display the
total miles, or kilometers, in the odometer. Your instrument
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 73

cluster display is designed to display important informa-
tion about your vehicle’s systems and features. Using a
driver interactive display located on the instrument panel,
your instrument cluster display can show you how sys-
tems are working and give you warnings when they are
not. The steering wheel mounted controls allow you to
scroll through the main menus and submenus. You can
access the specific information you want and make selec-
tions and adjustments.
Location And Controls
The instrument cluster display features a driver-interactive
display that is located in the instrument cluster.The menu items described below are an example of what
can be found in the vehicle’s menu:
•Dimmer
• Speed Beep
• Trip B
• Set Time
• Set Date
• Autoclose
• Units
Instrument Cluster Display Location
74 GETTING TO KNOW YOUR INSTRUMENT PANEL

•Language
• Buzzer Volume
• Belt Buzzer
• Day Lights
The system allows the driver to select information by
pushing the following buttons mounted on the instrument
panel to the right of the steering column:
• MENU Button
Push and release the MENUbutton for a time longer than
one second to access/select the information screens or submenu screens of a main menu item. Push and hold the
MENU
button for two seconds to reset displayed/selected
features that can be reset.
• UP Arrow Button
Push and release the uparrow button to scroll upward
through the main menu and submenus.
• DOWN Arrow Button
Push and release the downarrow button to scroll down-
ward through the main menu and submenus.
NOTE: If equipped with a Uconnect system, some of the
menu items will be present in the radio head unit. Refer to
“Uconnect Settings” in “Multimedia” for further informa-
tion.
Dimmer:
With headlights on and without entering in the menu, push
the upordown arrow button to increase or decrease the
brightness of the instrument panel, graphics and command
buttons.
Selecting An Option Of The Main Menu With Submenu:
1. Briefly push and release the MENUbutton to display
the first submenu option.
Instrument Cluster Display Control Buttons
4
GETTING TO KNOW YOUR INSTRUMENT PANEL 75

2. Push and release theupordown arrow button (by
single pushes) to scroll through all the submenu options.
3. Briefly push and release the MENUbutton to select the
displayed submenu option and to open the relevant
setup menu.
4. Push and release the upordown arrow button (by
single pushes) to select the new setting for this submenu
option.
5. Briefly push and release the MENUbutton to store the
new setting and go back to the previously selected
submenu option.
6. Push and hold the MENUbutton to return to the main
menu (short hold) or the main screen (longer hold).
Change Engine Oil — If Equipped
Your vehicle may be equipped with an engine oil change
indicator system. The “Change Engine Oil” message will
display in the instrument cluster display. The engine oil
change indicator system is duty cycle based, which means
the engine oil change interval may fluctuate, dependent
upon your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, push and release the
MENU
button. To reset the oil change indicator system
(after performing the scheduled maintenance), refer to the
following procedure.
1. Turn the ignition switch to the ON position (do not start the engine).
2. Fully push the accelerator pedal slowly, three times, within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.
Instrument Cluster Display Menu Items
Speed Beep
This function is used to set a speed limit (MPH or km/h);
the driver is alerted when this limit is exceeded.
To set the desired speed limit:
1. Push the MENUbutton briefly. The display will show
the wording (SPEED) and the unit (MPH) or (km/h)
previously set.
76 GETTING TO KNOW YOUR INSTRUMENT PANEL