2018 Ram 3500 key fob

NOTE:
The cargo light and bed lights (if equipped) will
also turn on for approximately 60 seconds when
a key fob unlock button is pushed, as part of the
Illuminated Entry feature.
Cargo Camera — If Equipped
• Your vehicle may be equipped with a CargoCamera that allows you to see an image of
the inside of the pickup box. The image will
be displayed on the Uconnect Display, lo-
cated on the center stack of the instrument
panel.
•
A display timer is initiated when the Cargo
Camera image is displayed. The image will
continue to be displayed until the display
timer exceeds 10 seconds and the vehicle
speed is above 8 mph (13 km/h), or the image
is deactivated by touching the Uconnect dis-
play.
NOTE:
If the vehicle speed remains below 8 mph
(13 km/h), the cargo camera image will be
displayed continuously until deactivated by
touching the Uconnect display.
Bed Light Switch Without RamBoxBed Light Switch With RamBox

•The Cargo Camera is located in the bottom
center area of the Center High-Mounted Stop
Lamp (CHMSL).
NOTE:
If snow, ice, mud or any foreign substance
builds up on the camera lens, clean the lens,
rinse with water and dry with a soft cloth. Do not
cover the lens.For further information, and applicable warn-
ings and cautions, please refer to the
Owner’s Manual athttps://www.mopar.com/en-us/
care/owners-manual.html
(U.S. Residents) or
www.owners.mopar.ca (Canadian Residents).
Bed Extender — If Equipped
The bed extender has three functional positions:
• Storage Position – maximizes the bed cargo area when not in use.
•
Divider Position – managing your cargo and
assisting in keeping cargo from moving around
the truck bed.
• Extender Position – extends the bed of the truck beyond the tail gate an additional
15 inches for additional cargo room.
Introduction To Keyless
Enter-N-Go
The Keyless Enter-N-Go — Passive Entry sys-
tem is an enhancement to the vehicles key fob.
This feature allows you to lock and unlock the
vehicle’s door(s) without having to push the key
fob lock or unlock buttons as well as starting
and stopping the vehicle with the push of a
button.
NOTE:
The key fob may not be found if it is located
next to a mobile phone, lap top or other elec-
tronic device; these devices may block the key
fob’s wireless signal.
Cargo Camera Display
KEYLESS ENTER-N-GO —
PASSIVE ENTRY

To Lock The Vehicle’s Doors:
With a valid Keyless Enter-N-Go key fob within
5 ft (1.5 m) of the driver or passenger front door
handles, push door handle lock button to lock
all doors.
Do NOT grab the door handle, when pushing the
door handle lock button. This could unlock the
door(s).
NOTE:
• After pushing the door handle lock button,you must wait two seconds before you can
lock or unlock the doors, using either Passive
Entry door handle. This is done to allow you
to check if the vehicle is locked by pulling
the door handle without the vehicle reacting
and unlocking.
• The Passive Entry system will not operate if the key fob battery is dead.
The vehicle doors can also be locked by using
the key fob lock button or the lock button
located on the vehicles interior door panel.
To Unlock From The Driver Or
Passenger Side:
With a valid Keyless Enter-N-Go key fob located
outside the vehicle and within 5 ft (1.5 m) of the
driver or passenger side door handle, grab either
front door handle to unlock the door automatically.
For further information, and applicable warnings
and cautions, please refer to the Owner’s Manual at
www.mopar.com/en-us/care/owners-manual.html
(U.S. Residents) orwww.owners.mopar.ca(Cana-
dian Residents).
Push The Button To Lock
Do NOT Grab The Handle When Locking
Grab The Door Handle To Unlock