2018 Peugeot iOn warning

12
Under-inflationFixed. The pressure in one or more of
the tyres is too low. Check the pressure in the tyres as soon as possible.
This check should preferably be carried out when the
tyres are cold.
You must reinitialise the system after adjusting one or
more tyre pressures and after changing one or more
wheels.
For more information on Tyre under-inflation
detection
, refer to the corresponding section.
Flashing, then fixed. The function is faulty and/or at
least one of the wheels has no
sensor detected. Tyre pressure monitoring is no longer ensured.
Have the system checked by a Peugeot dealer or a
qualified workshop.
Warning/indicator lamp
StateCause Action/Observations
Main electrical
system self-
diagnostic system Fixed.
Fault in the main electrical
system. You must stop as soon as it is safe to do so.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
Passenger's airbag
system Fixed, in the central
console.
The control switch, located in the
glove box or in the central console
(depending on equipment), is set
to the "
OFF" position.
The passenger's front airbag is
deactivated.Set the control switch to the " ON" position to activate
the passenger's front airbag.
In this case, do not install a "rear ward facing" child
seat on the front passenger seat.
Remember to check the status of this control switch
before starting your vehicle.
Rear foglamp Fixed. The rear foglamp has been
switched on using the ring on the
lighting control stalk. Turn the ring on the lighting control stalk to the rear to
switch off the rear foglamp.
Dashboard instruments

13
Warning/indicator lampStateCause Action/Observations
Left-hand direction
indicator Flashing with audible
signal. The lighting control stalk has been moved
down.
Right-hand
direction indicator Flashing with audible
signal. The lighting control stalk has been moved
up.
Hazard warning
lamps Flashing with audible
signal. The hazard warning lamps switch, located
on the dashboard, has been operated.
The left-hand and right-hand direction indicators and
their associated lamps flash simultaneously.
Sidelamps and/
or dipped beam
headlampsFixed.
The sidelamps and/or dipped beam
headlamps have been switched on.
Front foglamps Fixed. The front foglamps have been switched on
using the ring on the lighting control stalk. Turn the ring on the lighting control stalk
twice rear wards to switch off the front
foglamps.
Main beam
headlamps Fixed.
The lighting control stalk has been pulled
towards you. Pull the lighting control stalk to return to
dipped beam headlamps.
Motor braking
reduction Flashing.
The main battery is fully charged, the motor
braking is temporarily reduced. Anticipate when you need to brake: use
the brake pedal to slow down or stop the
vehicle.
Ready
(ready to drive)
Fixed, accompanied by
an audible signal when
it comes on.The vehicle is ready to drive, you can
operate the accelerator now.
The lamp stays on as long as the vehicle is
powered up.
Green warning/indicator lamps
Black warning/indicator lamps Blue warning/indicator lamps
1
Dashboard instruments

14
Main battery state of
charge indicator
Display
The state of charge of the main battery is
displayed continuously in the instrument panel.
Low energy alerts
Four successive energy level alerts indicate
that the energy available in the main battery
has dropped to a low level:
-

2 l
it and flashing bars on the energy gauge
in the instrument panel: starting to use the
reserve.
-

T
he final bar on the energy gauge flashes.
-

T
he final bar disappears: the range
display disappears, the heating and air
conditioning are cut off. -

D
isplay of this warning lamp
in the instrument panel:
progressive reduction in
available engine power.
Energy consumption/
generation indicator
System informing the driver of the level of
energy consumption or generation by the main
battery.
"Neutral" position
On switching on the ignition, your vehicle
neither consumes nor generates energy
through its electric drive train: the needle is in
the "neutral" position (provided the heating and
air conditioning are off).
Energy consumption
The needle moves to the right, in proportion to
the consumption of energy by the vehicle.
"Eco" zone
The needle is in this zone when the vehicle is
used in a way that limits the consumption of
electric energy and optimises its range.
Dashboard instruments

17
Resetting the service indicator
After each service, the service indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:
F
T
urn off the ignition (switch to LOCK or
ACC position).
F

P
ress the reset button A in succession until
the service indicator is displayed.
F

P
ress and hold the reset button down for a
few seconds to make the spanner flash .
F

P
ress the reset button whilst the spanner
is flashing to move the display " ---" to
" CLEAR ".
The distance (or the time) remaining before
the next ser vice is displayed. The distance "
---" indicating that the
ser vice is now due is reset automatically
after a certain time and a certain distance
travelled. The display will then indicate the
remaining time before the next service.
Under-inflation detection
You must reinitialise the under-inflation
detection system after adjusting one or more
tyre pressures and after changing one or more
wheels.
The procedure for this is as follows.
F

P
ress button A to select the system.
F

P
ress and hold button A down for at least
three seconds .
An audible signal sounds and the under-
inflation warning lamp flashes slowly until
reinitialisation has been completed.
1
Dashboard instruments

21
Doors
Opening
From outside
F After unlocking the vehicle using the remote control or the key, pull the door
handle.
From inside
F Pull the front or rear door control to open the door.
If the doors are locked:
-
o

pening the driver's door unlocks the other
doors,
-

t
he front passenger door or the rear doors
must first be manually unlocked using the
lock control before being opened.
Closing
If a door or the boot is not properly
closed, this warning lamp comes
on in the instrument panel until the
relevant door or the boot is closed.
Locking/unlocking from
inside
F Push the driver's door button for wards to lock or rear wards to unlock the entire
vehicle. The front and rear passenger door buttons
lock /unlock only the corresponding door.
Boot
Opening
F After unlocking the vehicle using the
remote control or the key, press the
handle


A, then raise the tailgate.
2
Access

34
Front demist – defrost
Place the air distribution
adjustment control in this position.
The intake of exterior air is selected (indicator
lamp off) and, depending on equipment, the air
conditioning comes on (indicator lamp lit). Place the temperature adjustment
control between "●" and " H".
Place the air flow adjustment
control in the desired position.
For fast demisting/defrosting, you can also
press the " MAX" button.
Rear screen demist –
defrost
Switching on
F Press this button to demist /
defrost the rear screen and,
depending on version, the door
mirrors. The button indicator
lamp comes on.
Switching off
Demisting/defrosting switches off automatically
to prevent an excessive consumption of
electricity.
F

I
t is possible to stop the
demisting/defrosting operation
before it is switched off
automatically by pressing the
button again. The warning lamp
for the button goes out. Switch off the demisting/defrosting of
the rear screen and door mirrors as
soon as appropriate in order to control
the vehicle's electrical consumption and
optimise its range.
Remote control
(Depending on equipment.)
The remote control can be used to control the
following functions remotely:
-

C
heck the vehicle's charge status.
-
R

echarge programming: start time and
charge duration.
-

A
ctivate the air conditioning functions
(heating, air conditioning, demist - defrost).
To programme recharging, the following
conditions must be met:
-

P
lace the drive selector in position P .
-

P
lace the switch to LOCK .
-

C
onnect the vehicle with the normal
recharging cable.
The remote control range is approximately
100
metres.
Ease of use and comfort

38
Malfunctions
Remote control
Warning/
indicator lampStateCausesAction/Observations
Flashes within approximately ten seconds
after switching on the remote control. There is a malfunction.
Switch the remote control off and then on
again.
Flash within approximately one second
after switching on the remote control. Electrical interference is preventing the
remote control or data transmission from
operating.Move away from the inter ference sources.
Flash within approximately ten seconds
after switching on the remote control. The aerial is not extended.
Extend the aerial.
You are outside the range of the remote
control. Move nearer to the vehicle.
The ignition switch is not in the LOCK
position. Turn the switch to LOCK
.
Ease of use and comfort

39
Charge programming
Warning/
indicator lampStateCauseAction/Observations
Flash for a few seconds. The charging cable is not connected
properly.Check the cable.
There is a problem with your electrical
installation. Have it checked by a qualified electrician.
Flashes for a few seconds. The drive selector is not in position P. Place the drive selector in position P .
Thermal comfort programming
Warning/
indicator lampState CauseAction/Observations
Flash for a few seconds. The charging cable is not connected
properly.Check the cable.
There is a problem with your electrical
installation. Have it checked by a qualified electrician.
Flash for a few seconds. The main battery is not sufficiently
charged.Charge the battery and start the
programming again.
Flashes for a few seconds. A vehicle door is still open.Close all the doors and start the
programming again.
The drive selector is not in position P . Place the drive selector in position P .
3
Ease of use and comfort