2018 Peugeot iOn light

40
Lighting control stalk
Main lighting
The various front and rear lamps of the vehicle
are designed to adapt the lighting gradually to
the climatic conditions and thus give the driver
better visibility:
-
s
idelamps, to be seen,
-

d
ipped beam headlamps to see without
dazzling other drivers,
-

m
ain beam headlamps to see clearly when
the road is clear.
Additional lighting
Other lamps are fitted to meet particular driving
conditions:
-

a r
ear foglamp to be seen from afar,
-
f

ront foglamps for even greater visibility,
-

d
aytime running lamps to be seen during
t h e d ay.
Selection ring for main
lighting mode
Turn it to align the desired symbol with the
mark.
Dipped or main beam headlamps.
Sidelamps.
Automatic illumination of headlamps.
Lighting off.
Headlamp dipping stalk
Pull the stalk to switch the lighting between
dipped/main beam headlamps.
In the lighting off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining a
pull on the stalk.
Displays
Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Lighting and visibility

41
Front and rear foglamps
Foglamps selection ring.
They operate with the sidelamps and dipped or
main beam headlamps.Front and rear foglamps:
F

T
urn the ring for wards once to switch on the
front foglamps.
F

T
urn the ring for wards twice to switch on the
rear foglamp.
F

T
urn the ring backwards once to switch off
the rear foglamp.
F

T
urn the ring backwards twice to switch off
the front foglamps. It is prohibited to switch on the front or
rear foglamps in fine weather or in rain,
night or day. In these situations, the power
of their beams may dazzle other drivers.
Do not forget to switch off the front
foglamps and the rear foglamp when they
are no longer necessary.
When lighting is left on
When the driver's door is opened, with the
ignition off, an audible signal warns the
driver that the vehicle's lighting is left on.
In this case, switching off the lighting
stops the audible signal.
Direction indicators
(flashing)The ring automatically returns to its initial
position.
The rear foglamp switches off automatically
when you switch off the sidelamps and dipped
or main beam headlamps.
F

L
eft: lower the lighting control stalk passing
the point of resistance.
F

R
ight: raise the lighting control stalk passing
the point of resistance.
Daytime running lamps
Specific daytime lighting to make the vehicle
more visible.
The daytime running lamps light up
automatically when the engine starts if no other
lamps are on.
They cannot be deactivated.
Although these lamps are located in the
same lamp unit as the front foglamps, they
operate with a specific bulb.
Their use complies with the Highway
Code.
4
Lighting and visibility

42
Automatic illumination/
switching off of the headlamps
Automatic illumination
When the lighting control stalk ring is in
the AUTO position, the sidelamps and
dipped beam headlamps are switched on
automatically, without any action on the part of
the driver, when a low level of ambient light is
detected.
As soon as the level of light becomes sufficient
again, the lights are switched off automatically.
The sensor is located at the bottom of the
windscreen.
Do not cover the sunshine sensor, as the
associated functions would no longer be
controlled.
In fog or snow, the sunshine sensor may
detect sufficient light. The headlamps may
not come on automatically.
Automatic switching off
When the lighting control stalk is in the "AUTO"
position, if the ignition key is in the "LOCK" or
"ACC" position or is removed, the headlamps
will automatically switch off when the driver's
door is opened .
Headlamp beam height
adjustment
To avoid causing a nuisance to other road
users, the height of the halogen headlamp
beams must be adjusted according to the load
in the vehicle.
0.Driver only or driver + 1 front
passenger.
1 or 2. 4 passengers (including driver).
3. 4 passengers (including driver) +
maximum authorised load.
4. Driver + maximum authorised load.
The initial setting is position " 0".
Wiper control stalk
The wipers are controlled directly by the driver
using control A and ring B .
In wintry conditions, remove snow, ice
or frost present on the windscreen,
around the wiper arms and blades and
the windscreen seal before operating the
wipers.
Do not operate the wipers on a dry
windscreen. Under extremely hot or cold
conditions, ensure that the wiper blades
are not stuck to the windscreen before
operating the wipers.
Lighting and visibility

43
Windscreen wipers
A.Wiping speed control lever: raise
or lower the lever to the desired
position.
Single wipe.
Of f.
Intermittent (manually adjustable
speed).
Slow.
Fast.
B. Intermittent adjustment ring.
F

T
urn this ring to increase or
decrease wiping frequency in
intermittent mode.
Front screenwash
Pull the wiper control stalk towards you. The
screenwash and then the wipers operate for a
preset time.
Rear wiper
C. Rear wiper selection ring.
Of f.
Intermittent wiping.
The wiper wipes twice then switches to
intermittent mode with an inter val of a few
seconds. Wash-wipe.
Hold the ring in this position to operate the
screenwash and to carry out several wipes with
the wipers.
Courtesy lamp
Position 1 "ON"
The courtesy lamp is permanently on.
Position 2 "●"
The courtesy lamp comes on when a door or
the boot is opened; when the door or boot is
closed again, the lighting dims gradually for a
few seconds before going out.
However, the courtesy lamp goes out
immediately when the doors and boot are
closed and you lock the vehicle from the inside
or with the remote control.
4
Lighting and visibility

44
Before leaving the vehicle, check that the
courtesy lamp is not still on.
If it remains permanently on, it will
discharge the ancillaries battery even if
the main battery is charged or charging.
It will then no longer be possible to start
the vehicle.
Position 3 "OFF"
The courtesy lamp is permanently off.
Lighting and visibility

46
Hazard warning lamps
F When you press this red button, all four direction indicators flash.
They can operate with the ignition off.
Brake lamps, automatic
operation
The brake lamps may light up automatically
when you release the accelerator pedal.
Their illumination is not systematic and
depends on the rate of deceleration.
Horn for pedestrians
(Depending on equipment.)
System to alert pedestrians to the presence of
the vehicle.
When the vehicle is started, illumination of
the button indicator lamp for a few seconds
indicates system activation.
Operation
Horn
F Press the central part of the steering wheel. The horn sounds when the vehicle speed is
between 0 and 22
mph (35 km/h),
Deactivation
In certain driving conditions you can deactivate
the system.
Press this button.
The button indicator lamp comes on and the
audible signal stops.
Another press reactivates the system.
The button indicator lamp goes off. Before deactivating the system, make
sure that you are not driving in an area
frequented by pedestrians.
The system is reactivated automatically at
every new start.
Malfunction
The button indicator lamp flashes if the system
malfunctions. Contact a PEUGEOT dealer
or a qualified workshop to have the system
checked.
Safety

48
** As per the geographic coverage of "Peugeot Connect SOS", "Peugeot Connect
Assistance" and the official national
language chosen by the owner of the vehicle.
The list of countries covered and PEUGEOT
CONNECT services is available from dealers
or on the website for your country.
Geo-location
If you purchased your vehicle outside the
PEUGEOT dealer network, we invite you
to have a dealer check the configuration of
these ser vices and, if desired, modify it to
suit your wishes.
In a multi-lingual country, configuration is
possible in the official national language
of your choice. For technical reasons and in particular
to improve the quality of PEUGEOT
CONNECT ser vices to customers, the
manufacturer reser ves the right to carry
out updates to the vehicle's on-board
telematic system.
The cancellation is confirmed by a voice
message.
You can deactivate geo-location by
simultaneously pressing the "Peugeot Connect
SOS" and "Peugeot Connect Assistance"
buttons, followed by pressing "Peugeot
Connect Assistance" to confirm.
To reactivate geolocation, simultaneously press
the "Peugeot Connect SOS" and "Peugeot
Connect Assistance" buttons again, followed
by a press on "Peugeot Connect Assistance"
to confirm.
Braking assistance
systems
Group of supplementary systems which help
you to obtain optimum braking in complete
safety in emergency situations:
-

a
nti-lock braking system (ABS),
-

e
lectronic brake force distribution (EBFD),
-
em

ergency braking assistance (EBA).
Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the stability and
manoeuvrability of your vehicle when braking,
in particular on poor or slippery sur faces.
Activation
The anti-lock braking system comes into
operation automatically when there is a risk of
wheel lock.
Normal operation of the ABS may make itself
felt by slight vibrations of the brake pedal.If you need to brake in an emergency,
press very firmly and maintain this
pressure.
Malfunction
Stationary vehicle If this warning lamp comes on,
it indicates an anti-lock braking
system malfunction that could cause
control of the vehicle to be lost
during braking.
Contact a PEUGEOT dealer or a qualified
workshop.
Safety

53
Advice
The driver must ensure that passengers use
the seat belts correctly and that they are all
restrained securely before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do not interchange the seat belt buckles as
they will not completely fulfil their role.
The seat belts are equipped with an
inertia reel which allows the strap length
to automatically adjust to your shape. The
seat belt returns to its storage position
automatically when it is not used.
Before and after use, ensure that the seat belt
is reeled in correctly.
The lower part of the strap must be positioned
as low as possible on the pelvis.
The upper part must be positioned in the
hollow of the shoulder.
The inertia reels are fitted with a device which
automatically locks the strap in the event
of a collision or emergency braking or if the
vehicle rolls over. You can release the device
by pulling the strap firmly and then releasing it
so that it reels in slightly.In order to be effective, a seat belt:
-
M ust be tightened as close to the body as
possible,
-

M
ust be pulled in front of you with a
smooth movement, ensuring that it is not
twisted,
-

M
ust only be used to secure one person,
-

M
ust not show signs of tearing or fraying,
-

M
ust not be changed or modified, in order
to avoid affecting its performance.
In accordance with current safety regulations,
for all repairs on your vehicle's seat belts, go
to a qualified workshop with the skills and
equipment needed, which a PEUGEOT dealer
is able to provide.
Have your seat belts checked regularly by a
PEUGEOT dealer or by a qualified workshop,
particularly if the straps show signs of
damage.
Clean the seat belt straps with soapy water or
a textile cleaning product, sold by PEUGEOT
dealers.
After folding or moving a seat or a rear bench
seat, ensure that the seat belt is positioned
and reeled in correctly. Instructions for children
Use a suitable child seat, if the passenger is
less than 12
years old or shorter than one and
a half metres.
Never use the same seat belt to secure more
than one person.
Never allow a child to travel on your lap.
For more information on Child seats , refer to
the corresponding section.
In the event of an impact
Depending on the nature and seriousness
of the impacts , the pyrotechnic device may
trigger before and independently of airbag
deployment. Deployment of the pretensioners
is accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp comes
on.
After an impact, have the seat belt system
checked and, if necessary, replaced
by a PEUGEOT dealer or a qualified
workshop.
5
Safety