2018 Peugeot 301 lock

105
Procedure
Before topping up, ensure that the vehicle is
parked on a flat and level sur face.
In wintry conditions, ensure that the
temperature of the vehicle is above -11°C.
Otherwise the AdBlue
® may be frozen and
so cannot be poured into its tank. Park your
vehicle in a warmer area for a few hours to
allow the top-up to be carried out.
F

S

witch off the ignition and remove the key.
F

Un

clip the plastic plug. F

C
arefully lift off the cap, without dropping it.
F

F

or access to the AdBlue
® tank, open the
boot, remove the boot floor and then lift out
the storage box containing the tools.
F

I

nsert your fingers into the aperture and turn
the blue cap 1/6 of a turn anti-clockwise. F

G
et a bottle or container of AdBlue
®. After
first checking the use-by date, carefully
read the instructions on use on the label
before pouring the contents of the bottle into
your vehicle's AdBlue
® tank.
Important: if your vehicle's AdBlue
® tank is
c
ompletely empty – which is confirmed by
the alert displays and the impossibility of
starting the engine – you must add at least
3.8

litres (so two 1.89

litre bottles).
F

A

fter emptying the bottle or container, wipe
away any spillage around the tank filler
using a damp cloth. If any additive is spilt or splashed, wash
immediately with cold water or wipe with a
damp cloth.
If the additive has crystallised, clean it off
using a sponge and hot water.
F
R
efit the blue cap to the tank and turn it 1/6
of a turn clockwise, to its stop.
F
R
eplace the plastic plug, clipping it in the
opening.
F
R
eturn the storage box containing the tools
to its location.
F
R
eplace the boot floor and close the boot.
Never dispose of AdBlue
® additive
bottles or containers in the household
waste. Place them in a container
provided for this purpose or take them
to your dealer.
Important: if topping up after running
out of AdBlue , you must wait for
approximately 5 minutes before switching
the ignition back on, without opening
the driver's door, unlocking the vehicle
or inser ting the key into the ignition
switch . Switch on the ignition, then, after
10 seconds, start the engine.
7
Practical information

124
Removing a wheel
Parking the vehicle
* position P for the automatic gearbox
Park the vehicle where it does not block
traffic: the ground must be level, stable
and non-slippery.
Apply the parking brake, switch off the
ignition and engage first gear* so as to
block the wheels.
Check that the parking brake warning
lamp comes on fixed in the instrument
panel.
The occupants must get out of the vehicle
and wait where they are safe.
Make sure that the jack is correctly
positioned at one of the vehicle's jacking
points.
Incorrect use of the jack could cause the
vehicle to collapse.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Do not use a jack other than the one
supplied by the manufacturer.
Wheel with hub cap
When removing the wheel
, first remove
the hub cap using the wheelbrace by
pulling at the valve aperture.
When refitting the wheel , after tightening
the wheel bolts, refit the hub cap, starting
by placing its aperture in line with the
valve and then pushing it into place all
round its edge with the palm of your hand.
List of operations
F Remove each wheel bolt cover using the tool 3 (alloy wheels).
F

L
oosen the bolts using wheelbrace 1 o n l y. F

P
lace the foot of jack 2 on the ground and
ensure that it is directly below the front
A or rear B jacking point provided on the
underbody, whichever is closest to the
wheel to be changed.
In the event of a breakdown

127
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps is
normal; it disappears after the lamps have
been on for a few minutes.
Front lamps
Halogen headlampsHalogen headlamps with daytime
running lamps and foglamps
1
Direction indicators (PY21W).
2 Main beam headlamps (H1).
3 Dipped beam headlamps (H7LL).
4 Sidelamps (W5W). 1
Direction indicators (PY21W).
2 Main beam headlamps (H1).
3 Dipped beam headlamps (H7LL).
4 Daytime running lamps/Sidelamps
(LEDs).
5 Fo g l a m p s ( H11) .
Light-emitting diodes (LEDs)
For the replacement of this type of bulb,
go to a PEUGEOT dealer or a qualified
workshop.
Direction indicators
Quicker flashing of the direction indicator
lamp (left or right) indicates that one of
the bulbs on the corresponding side has
failed.
F

T
urn the connector a quarter turn anti-
clockwise.
F

P
ull the bulb connector.
F

R
emove the bulb and replace it.
To refit, carry out these operations in reverse
o r d e r.
Amber colour bulbs, such as the direction
indicators, must be replaced by bulbs with
identical colour and specifications.
To refit, close the protective cover very
carefully to guarantee the leak-tightness
of the lamp.
8
In the event of a breakdown

129
Foglamps
To refit, proceed in reverse order.If you experience any difficulty in replacing
these bulbs, contact your PEUGEOT
dealer or a qualified workshop.
Direction indicator side repeaters
Contact a PEUGEOT dealer or a qualified
workshop to obtain the module.
F

I

nsert a flat screwdriver between the lamp
and the cover.
F

P

ull and lever to unclip the cover.
F

R

emove the two fastening screws of the
module.
F

R

emove the module from its housing. F

P

ress the locking clip and disconnect the
connector.
F

T

urn the bulb holder a quarter turn anti-
clockwise.
F

R

emove the bulb holder.
F

R

emove the bulb and replace it.
F

I

nsert a screwdriver towards the centre of
the repeater between the repeater and the
lower bodywork.
F

L
ever with the screwdriver to extract the
repeater and pull it out.
F

D
isconnect the repeater connector.
F

R
eplace the module.
For reassembly, carry out these operations in
reverse order.
8
In the event of a breakdown

138
Never try to charge a frozen battery – risk
of explosion!
If the battery has frozen, have it checked
by a PEUGEOT dealer or by a qualified
workshop who will check that the internal
components have not been damaged and
that the container has not cracked, which
would mean a risk of toxic and corrosive
acid leaking.
Disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of ser vice for a long
period.
Before disconnecting the battery:
F
C
lose all openings (doors, boot, windows).
F

S
witch off all electricity consuming devices
(audio system, wipers, lighting, etc.).
F

S
witch off the ignition and wait for four
minutes.
After accessing the battery, you only have to
disconnect the (+) terminal.
Quick-release terminal clamp
Disconnecting the (+) terminal
Reconnecting the (+) terminal
Do not force the lever as locking will be
impossible if the clamp is not positioned
correctly; start the procedure again.
After reconnecting the battery
F Raise the lever A fully to release the clamp B.
F

R
emove the clamp B by lifting it off.
F

Ra
ise the lever A fully.
F

R
efit the open clamp B on the (+) terminal.
F

P
ush the clamp B fully down.
F

L
ower the lever A to lock the clamp B .After reconnecting the battery, turn on the
ignition and wait 1
minute before starting
the engine, in order to enable the electronic
systems to initialise.
If minor problems nevertheless persist
following this operation, contact a PEUGEOT
dealer or a qualified workshop.
Referring to the corresponding section, you
must reinitialise certain systems yourself, such
as:
-

T
he key with remote control.
-

T
he date and time.
-

T
he preset radio stations.
The Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the exterior
temperature and the state of charge of the
battery (up to about 8 hours).
In the event of a breakdown

139
Towing the vehicle
Procedure for having your vehicle towed.
Access to the tools
General recommendations
Obser ve the legislation in force in your
c o u nt r y.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing arm; rope and straps are
prohibited.
The towing vehicle must move off gently.
When the vehicle is towed with its engine
off, there is no longer braking and steering
assistance.
In the following cases, you must always
call on a professional recovery ser vice:
-
v
ehicle broken down on a motor way or
fast road,
-
f

our-wheel drive vehicle,
-

w
hen it is not possible to put the
gearbox into neutral, unlock the
steering, or release the parking brake,
-

t
owing with only two wheels on the
ground,
-

w
here there is no approved towbar
available.Towing your vehicle
F On the front bumper, unclip the cover by pressing on its left side.
The towing eye is installed in the boot under
t h e f l o o r.
To gain access to it:
F

O

pen the boot.
F

L

ift the floor and remove it.
F

R

emove the towing eye from the holder. F

S
crew the towing eye in fully, until it reaches
a stop.
F

I
nstall the towbar.With a manual gearbox, place the gear
lever into neutral.
With an automatic gearbox, place the gear
selector into position N .
Failure to follow this instruction may cause
damage to some components (braking,
powertrain, etc.) and the absence of
braking assistance when the engine is
restarted.
8
In the event of a breakdown

140
Towing another vehicle
This towing is strictly prohibited (risk of
damaging your vehicle).
F

U
nlock the steering by turning the ignition
key one notch and release the parking
brake.
F

S
witch on the hazard warning lamp on both
vehicles.
F

S
et off gently, drive slowly and for a short
distance.
In the event of a breakdown

19
or Press on "
Telephone " to display the
CarPlay
® inter face.
Or Connect a USB cable. The
smartphone charges when
connected by a USB cable.
or From the system, press
"
Applications " to display the
primary page.
Press " Connectivity " to go to the CarPlay
®
function.
Press on " CarPlay" to display the
CarPlay
® inter face.
On connecting the USB cable, the
CarPlay
® function deactivates the
system's Bluetooth® mode.
MirrorLinkTM smartphone
connection
As a safety measure and because it
requires sustained attention by the driver,
using a smartphone when driving is
prohibited.
All operations must be done with the
vehicle stationary .
The synchronisation of a personal
smartphone allows users to display
applications adapted for the smartphone's
MirrorLink
TM technology on the vehicle
sc
reen.
The workflow and standards
are constantly changing, for the
communication process between the
smartphone and the system to operate,
it is essential that the smartphone is
unlocked; update the operating system of
the smartphone as well as the date and
time of the smartphone and the system.
For the list of eligible smartphones, go
to the Brand's internet website in your
c o u nt r y. As a safety measure, applications can
only be viewed with the vehicle stationary;
display is interrupted once the vehicle is
moving.
The "
MirrorLink
TM" function requires
the use of a compatible smartphone and
applications.
When connecting a smartphone
to the system, it is recommended
that Bluetooth
® be started on the
smartphone.
Connect a USB cable. The
smartphone charges when
connected by a USB cable.
or From the system, press
"
Applications " to display the
primary page.
Press " Connectivity " to go to the MirrorLink
TM
function.
Press "MirrorLink
TM" to start the
application in the system.
.
PEUGEOT Connect Nav