2018 Peugeot 301 ignition

31
Lost keys
Go to a PEUGEOT dealer with the vehicle's
registration document, your personal
identification documents and if possible the
key code label.
The PEUGEOT dealer will be able to look
up the key code and the transponder code
required to order a new key.Do not throw away the remote control
batteries, they contain metals which are
harmful to the environment.
Take them to an approved collection
point.Anti-theft protection
Do not make any modifications to the
electronic engine immobiliser system; this
could cause malfunctions.
Remote control
The high frequency remote control is a
sensitive system; do not operate it while it is
in your pocket as there is a possibility that
it may unlock the vehicle, without you being
aware of it.
Do not repeatedly press the buttons of your
remote control out of range and out of sight of
your vehicle. You risk making it inoperative. It
will then be necessary to reinitialise it again.
No remote control can operate when the key
is in the ignition switch, even when the ignition
is switched off, except for reinitialisation.
Locked vehicle
Driving with the doors locked may render
access by the emergency services to the
interior difficult in an emergency.
As a safety precaution, never leave children
alone in the vehicle, except for a very short
period.
In all cases, it is essential to remove the key
from the ignition switch when leaving the
vehicle. Second-hand vehicle
Have the pairing of all of the keys in your
possession checked by a PEUGEOT dealer,
to ensure that only your keys can be used to
open and start the vehicle.
2
Access

32
Alarm
System which protects and provides a deterrent
against theft and break-ins. It provides
perimeter protection and a self-protection
function.
Perimeter protection
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot, the bonnet, etc.Self-protection function
The system checks for the putting out of
ser vice of its components.
The alarm is triggered if the battery, the
central control or the siren wiring are put
out of ser vice or damaged.
For all work on the alarm system, contact
a PEUGEOT dealer or a qualified
workshop.
Locking the vehicle with
alarm
Activation
F Press the locking button on the remote control.
The alarm is activated: an indicator
lamp in the switch panel to the left of
the steering wheel flashes once per
second.
Deactivation
F Press the unlocking button on the remote control.
The alarm is deactivated: the
indicator lamp goes off.
Triggering of the alarm
F Turn the vehicle off and exit.
The perimeter protection is activated 5
seconds
after pressing the locking button on the remote
control.
If an opening (door, boot, etc.) is not closed
fully, the vehicle will not be locked, but the
alarm will be activated. When the vehicle is unlocked using
the remote control, rapid flashing of
the indicator lamp informs you that
the alarm was triggered during your
absence. Upon ignition, this flashing
stops immediately.
This is indicated by sounding of the siren and
flashing of the direction indicators for thirty
seconds.
Locking the vehicle without
activating the alarm
F Lock the vehicle using the key.
Failure of the remote control
To deactivate the monitoring functions:
F
U nlock the vehicle using the key.
F

O
pen the door; this sets off the alarm.
F

S
witch on the ignition; this stops the alarm.
Operating fault
When the ignition is switched on, continuous illumination
of the indicator lamp indicates a fault with the system.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
Access

36
Electric controls
Deactivating the rear electric
window controls
For the safety of your children, press
this button to deactivate all the rear
electric window controls, irrespective
of their positions.
When the indicator is on, all controls are
inhibited. When the indicator is off, all controls
are active. Always remove the key from the ignition
when leaving the vehicle, even for a short
time.
In the event of contact /pinching during
operation of the windows, you must
reverse the movement of the window. To
do this, press the switch concerned.
When operating the passenger electric
window controls, the driver must ensure
that no-one is preventing correct closing
of the windows.
The driver must ensure that all
passengers make correct use of electric
windows.
Be particularly aware of children when
operating the windows.
1
Front left.
2 Front right.
3 Rear right.
4 Rear left.
5 Deactivating the rear electric window
control switches.
To open or close the window, press or pull the
switch. The window stops as soon as the switch
is released.
The electric window controls remain active
for approximately 45 seconds after the
ignition is turned off, or until a front door is
opened. During this period of 45 seconds,
if you open a door while operating a
window, the window stops. Any new
electric window command will be ignored
until the ignition is switched back on.
Model with front electric windows
Model with front and rear electric windows
Window controls
Manual controls
Turn the window handle located on the door
panel.
Access

51
Lighting control stalk
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps is
normal; it disappears after the lamps have
been on for a few minutes.
Travelling abroad
The design of the dipped beam headlamps
allows, without modification, driving in a
country that drives on the other side of
the road than the country in which your
vehicle was sold.
Selection ring for main
lighting mode
Lighting off (ignition off)/Daytime
running lamps (engine running).
Sidelamps only.
Dipped or main beam headlamps.
Dipping the headlamps
Pull the stalk to switch the lighting
between dipped and main beam
headlamps.
When the lighting is off or only the sidelamps
are on, the driver can switch on the main beam
headlamps by pulling the stalk.
Display
Turn to align the desired symbol with the mark. Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Foglamp selection ring
The foglamps operate with the dipped and main
beam headlamps.
Rear foglamp only
F To switch it on, turn the ring for wards.
F
T o switch it off, turn the ring rear wards.
4
Lighting and visibility

52
Front foglamps and rear foglamp
Turn and release the ring:
F O nce for wards to switch the front foglamps
on.
F

A s
econd time for wards to switch the rear
foglamp on.
F

O
nce rearwards to switch the rear foglamp
of f.
F

A s
econd time rear wards to switch the front
foglamps off.
The foglamps and sidelamps remain on if the
dipped beams are switched off manually.
F

T
urn the ring rear wards to switch the
foglamps off; the sidelamps will then switch
of f. In good or rainy weather, by both day
and night, using the front foglamps and
the rear foglamp is prohibited. In these
situations, the power of their beams may
dazzle other drivers. They should only be
used in fog or falling snow.
In these weather conditions, it is your
responsibility to switch on the foglamps
and dipped headlamps manually as the
sunshine sensor may detect sufficient
light.
Do not forget to turn off the front foglamps
and the rear foglamp as soon as they are
no longer necessary.
Switching off the lighting when the
ignition is switched off
On switching off the ignition, all of the
lamps turn off immediately, except for
dipped beam if automatic guide-me-home
lighting is activated.
Switching on the lighting after
switching off the ignition
To reactivate the lighting control stalk,
rotate the ring to the "0" position – lighting
off, then to the desired position.
When the driver's door is opened, a
temporary audible signal warns you that
the vehicle's lighting is on.
The lighting, with the exception of the
sidelamps, switches off automatically after
a maximum duration of thirty minutes to
prevent discharging of the battery.
Daytime running lamps
(Depending on the country of sale.)
When starting the vehicle, the daytime running
lamps come on automatically, if the lighting
control is in the "0" position.
The daytime running lamps go off
when the sidelamps, dipped beam
or main beam headlamps are
switched on.
This function cannot be deactivated.
Lighting and visibility

53
Manual guide-me-home
lighting
The temporary illumination of the dipped beam
headlamps after the vehicle's ignition has been
switched off makes the driver's exit easier
when the light is poor.
Switching on
F With the ignition off, "flash" the headlamps using the lighting control stalk.
F

A f
urther "headlamp flash" switches the
function off.
Switching off
Manual guide-me-home lighting goes off
automatically at the end of a given period of
time.
Automatic guide-me-home
lighting
When the automatic headlamp illumination
function is activated (lighting control stalk in the
" AUTO " position), under low ambient light the
dipped beam headlamps remain on when the
ignition is switched off.
With audio system
The guide-me-home lighting can be
configured in the " Personalisation-
configuration " menu.
With touch screen
The guide-me-home lighting can be
configured in the " Driving/Vehicle "
menu.
Direction indicators
Three flashes
F Press briefly upwards or downwards, without going beyond the point of
resistance; the direction indicators will flash
3 times.
F

L
eft: lower the lighting control stalk passing
the point of resistance.
F
R
ight: raise the lighting control stalk passing
the point of resistance.
4
Lighting and visibility

55
Front windscreen wash
Pull the wiper control stalk towards you. The
windscreen washer and then the wiper operate
for a fixed time.The screenwash jets are not adjustable.
Do not try to move them (risk of damage).
Special position of the
windscreen wipers
This maintenance position is used for cleaning
or replacement of the wiper blades. It can also
be useful, in winter, to release the wiper blades
from the windscreen.
F

O
perate the wiper stalk within one minute
after switching off the ignition to position the
wiper blades vertically on the windscreen. F

T
o park the wiper blades again, switch on
the ignition and operate the wiper stalk.
To maintain the effectiveness of the wiper
blades, it is advisable to:
-
h
andle them with care,
-
c
lean them regularly using soapy
water,
-
a
void using them to retain cardboard
on the windscreen,
-
r
eplace them at the first signs of wear.
Courtesy lamps
A
Courtesy lamps
B Map reading lamps
4
Lighting and visibility

56
Front and rear courtesy lamps
In this position, the courtesy lamp
comes on gradually:
In permanent lighting mode, the lighting time
varies according to the circumstances:
- When the ignition is off, approximately ten minutes.
-

I
n energy saving mode, approximately
thirty seconds.
-

W
hen the engine is running, no limit.
Front map reading lamps
F With the ignition on, press the corresponding switch.
-
W

hen unlocking the vehicle.
-

W

hen the key is removed from the ignition
switch.
-
W

hen opening a door.
-

W

hen activating the locking button on
the remote control in order to locate your
vehicle.
It switches off gradually:
-
W

hen locking the vehicle.
-

W

hen the ignition is switched on.
-

3

0

seconds after the last door is closed. Permanently off.
Permanent lighting.
Lighting and visibility