2018 MITSUBISHI OUTLANDER PHEV stop start

NOTElIf the seat belt (A) or ring (B) becomes dirty,
the belt may not retract smoothly. If the seatbelt and ring are dirty, clean them with a
mild soap or detergent solution.Seat belt reminder
E00409801973
For the driver and the front
passenger’s seat
*-This warning lamp shows the case
of the left-hand drive vehicles.
If the operation mode of the power switch is put in ON while a seat belt is not fastened,
the warning lamp comes on and the tone sounds for about 6 seconds to remind the
driver and the front passenger to fasten the
seat belt.
If the vehicle is driven with the seat belt still
unfastened, the warning lamp will blink and
the tone will sound intermittently until the
seat belt is fastened. At the same time, “FAS- TEN SEAT BELT” is displayed on the infor-
mation screen in the multi information dis-
play for the driver.WARNINGl Do not install any accessory or sticker
that makes the lamp difficult to see.NOTEl If the seat belt subsequently remains unfas-
tened, the warning lamp and the tone will is-
sue further warnings each time the vehicle starts moving from a stop.
l For the front passenger seat, the warning
function works only while a person is sitting
on the seat.
l When luggage is placed on the front passen-
ger seat, a sensor in the seat cushion may,
depending on the weight and position of the
luggage, cause the warning tone to sound
and the warning lamp to come on.
Seat belts
5-11OGGE18E1Seats and seat belts5 For the driverFor the front passenger

ScreenCauseSolution (Reference)lCharging was interrupted due to poor con-
nection of the charge cable or power fail- ure.l Connect the charge cable correctly.
Refer to “Normal charging” on page 3-10.
Refer to “Quick charging” on page 3-17.
l If charging is interrupted due to a power
failure, charging will be automatically re-sumed when the power is restored.l The drive battery temperature is too cold.l When the vehicle is under running, stop
the vehicle in a safe place and contact a MITSUBISHI MOTORS Authorized
Service Point.
l When the vehicle is parked during the
daytime, wait for the outside temperature to rise and re-start the Plug-in hybrid sys-tem once the outside temperature has ris-
en.
Refer to “Cautions and actions to deal with intense cold” on page 2-10.l Charging lid is open.l Close the charge lid.
Refer to “Charging from rated AC
220-240 V outlet” on page 3-12.l EV priority mode is not available because
the drive battery level is low.l Refer to “EV switch” on page 7-25.
Indication lamp, warning lamp, and information screen display list
6-24OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the electronic immobil-
izer (Anti-theft starting system).l Put the operation mode in OFF, and then
start the Plug-in Hybrid EV System again.If the warning is not cancelled, please
contact a MITSUBISHI MOTORS Au-
thorized Service Point.l The driver’s door is open when the opera-
tion mode is in any mode other than OFF.l Put the operation mode in OFF.
Refer to “Operation mode ON reminder
system” on page 7-14.l An attempt was made to lock all the doors
and the tailgate when the operation mode
is in any mode other than OFF.l Put the operation mode in OFF.
Refer to “Operation mode OFF reminder system” on page 7-13.l There is a fault in the electrical system.l Immediately stop the vehicle in a safe
place.
We recommend you to contact a MITSUBISHI MOTORS Authorized
Service Point.l The engine is overheated.lStop the vehicle in a safe place and take
corrective measures.
Refer to “Engine overheating” on page 9-04.l You put the operation mode in ON with-
out fastening your seat belt.l Fasten your seat belt properly. Refer to
“Seat belt reminder” on page 5-11.
Indication lamp, warning lamp, and information screen display list
6-29OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the Active Stability
Control (ASC).l We recommend you to have it checked.
Refer to “Active stability control (ASC)” on page 7-40.l There is a fault in the hill start assist.lWe recommend you to have it checked.
Refer to “Hill start assist” on page 7-34.l The outside temperature is
3 °C (37 °F) or
less.l Be careful of ice on the road.
l The road can be icy even when this warn-
ing is not displayed, so drive carefully.l The Adaptive Cruise Control System
(ACC) has detected the approach of the
vehicles in front.l Increase the following distance by de-
pressing the brake pedal or marking other
decelerating control.
Refer to “Adaptive Cruise Control System
(ACC): Proximity alarm” on page 7-55.l The Forward Collision Mitigation System
(FCM) has detected the danger of colli- sion.l Take appropriate action such as depress-
ing the brake to avoid collision.
Refer to “Forward collision warning func- tion” on page 7-65.l The Adaptive Cruise Control System
(ACC) detected a stop of the vehicle infront and stopped your vehicle, but the
brake will be released soon.l Depress the brake pedal as soon as your
vehicle comes to a stop.
Refer to “Adaptive Cruise Control System
(ACC)” on page 7-52.l The Electric parking brake cannot be ap-
plied automatically.l Depress the brake pedal as soon as possi-
ble.
Refer to “Brake auto hold” on page 7-32.
Indication lamp, warning lamp, and information screen display list
6-33OGGE18E1Instruments and controls6

2- Remaining distance displayShows the distance to the location where
the guidance is displayed.NOTEl Please read this section and also the separate
owner’s manual for MITSUBISHI Multi-
Communication System (MMCS).Other interrupt displays
E00524202338
ScreenSystem operation statusReferencel When you pressed the power switch and
the operation mode become the ACC
without depress the brake pedal, this
screen is displayed.
This screen will be displayed repeatedly at regular intervals while the operation mode of the power switch is put in ACC.l Place the select position in the “P” (PARK)
position, depress the brake pedal more
firmly than usual with the right foot. Then,
press the power switch.
Refer to “Starting and stopping the Plug-in Hybrid EV System” on page 7-14.l When Plug-in Hybrid EV System does
not start even if the operation mode of the power switch is put in ON, this screen is displayed.l When starting the Plug-in Hybrid EV Sys-
tem, you pressed the power switch with- out select position in the “P” (PARK) po-
sition.l Place the select position in the “P”
(PARK) position by pressing the electrical
parking switch, depress the brake pedal more firmly than usual with the right foot.
Then, press the power switch.
Refer to “Starting and stopping the Plug- in Hybrid EV System” on page 7-14.
Indication lamp, warning lamp, and information screen display list
6-41OGGE18E1Instruments and controls6

The setting for rest interval can be changed.ScreenSolutionStop the vehicle in a safe place, stop the Plug-in Hybrid EV system, and take a rest.
Use this display as rough guide for taking rests during a long drive.
The interval from the start of your trip until this message is displayed can be set. Refer to “REST REMINDER” on page 6-19.
The display and buzzer alert the driver when the set time is reached. If you continue
to drive without having a rest, the buzzer sounds about every 5 minutes to encourage
you to take a rest.
l In the following cases, the time driven is reset and the display returns to the pre-
vious display screen. After this, when the set time is reached again, the buzzer
and display encourage you to take a rest. • The buzzer sounds 3 times.
• Put the operation mode in OFF.
• The multi information display switch is held for about 2 seconds or more.

Indication lamps
E00501600100Turn-signal indication lamps/
Hazard warning indication lamps
E00501701427
These indication lamps blink
in the following situations.
l When the turn-signal
lever is moved to acti-
vate a turn-signal lamp.
Refer to “Turn-signal
lever” on page 6-60.
l When the hazard warning flasher switch
is pressed to activate the hazard warning
lamps.
Refer to “Hazard warning flasher switch” on page 6-60.
l When the hazard warning lamps auto-
matically activate due to sudden braking
while driving. (Vehicle equipped with emergency stop signal system)
Refer to “Emergency stop signal sys-
tem” on page 7-36.High-beam indication lamp
E00501800173
This indication lamp illumi-
nates when the high-beam is used.
Indication lamps
6-47OGGE18E1Instruments and controls6

Front fog lamp indication lamp
E00501901650
This lamp illuminates while
the front fog lamps are on.
Rear fog lamp indication lamp
E00502001241
This lamp illuminates whilethe rear fog lamp is on.
Position lamp indication lamp
E00508900173
This indication lamp illumi-
nates while the position lamps are on.
Ready indicator
E00530101061
The ready indicator keeps
flashing until the Plug-in
Hybrid EV System is activa- ted. When the Plug-in Hy-
brid EV System has activa- ted normally and the vehicle
becomes ready to run, the lamp stops flashing
and stays lit. Refer to “Starting the Plug-in
Hybrid EV System” on page 7-14.
If the indicator keeps flashing, the vehicle cannot be driven.
Charging indicator
E00530201062
This indicator flashes when the EV charging cable or
quick charging cable is con- nected.
After that, the lamp switches to being illuminated when
charging starts and goes out when charging is
completed.
NOTEl Although it is possible to start the Plug-in
Hybrid EV System if quick charging has notfinished normally, the charging indicator is
continuously blinking.
Refer to “Charging troubleshooting guide” on page 3-21.Warning lamps
E00502400147Brake warning lamp (red)
E00502504016
This lamp illuminates whenthe operation mode of thepower switch is put in ON,
and goes off after a few sec- onds.
Always make sure that the
lamp goes off before driving.
With the operation mode in ON, the brake
warning lamp illuminates under the following conditions:
l When the parking brake lever has been
engaged.
l When the brake fluid level in the reser-
voir falls to a low level.
l When the braking system is an abnor-
mality.
With the operation mode in ON, a buzzer sounds under the following condition:
Warning lamps
6-48OGGE18E1Instruments and controls6

This lamp will also illuminate when the oper-
ation mode of the power switch is put in ON,
and goes off after the Plug-in Hybrid EV System has started. If it does not go off after
the Plug-in Hybrid EV System has started, we recommend you to have the vehicle
checked.CAUTIONl Prolonged driving with this lamp on may
cause further damage to the emission control system. It could also affect fuel economyand drivability.
l If the lamp does not illuminate when the op-
eration mode is put in ON, we recommend
you to have the system checked.
l If the lamp illuminates while the Plug-in Hy-
brid EV System is operating, avoid driving
at high speeds and have the system inspected by a MITSUBISHI MOTORS Authorized
Service Point as soon as possible.NOTEl The engine electronic control module ac-
commodating the onboard diagnostic system has various fault data (especially about the
exhaust emission) stored.
This data will be erased if a auxiliary battery
cable is disconnected which will make a rap- id diagnosis difficult. Do not disconnect a
auxiliary battery cable when the check engine
warning lamp is ON.
Auxiliary battery charge warn-
ing lamp
E00502702287
This warning lamp will illu-
minate when there is a fault with the charging system of
the auxiliary battery.
Normally, when the opera-
tion mode of the power
switch is put in ON, this warning lamp will illuminate. Then, when the Plug-in Hybrid
EV System is started and the ready indicator
illuminates, the warning lamp will go out.
CAUTIONl If the warning lamp stays on after the ready
indicator illuminates, there may be a prob- lem with the charging system for the auxili-
ary battery.
• Immediately park your vehicle in a safe
place and we recommend you to have it
checked.
• Do not charge the auxiliary battery.Plug-in Hybrid EV System
warning lamp
E00537300049
This warning lamp will illu-
minate when there is a fault at the Plug-in Hybrid EV
System.
Refer to “Service precau- tions” on page 11-02.
Normally, this warning lamp illuminates when the operation mode of the power switch
is put in ON, and goes off after a few sec-
onds.
CAUTIONl If the warning lamp illuminates and “EV
SYSTEM SERVICE REQUIRED STOP SAFELY” warning is displayed on the multi information display while the Plug-in Hy-
brid EV System is running, park your vehi-
cle in a safe place as soon as possible and contact a MITSUBISHI MOTORS Author-
ized Service Point to have the system checked.
Warning lamps
6-50OGGE18E1Instruments and controls6