2018 MITSUBISHI OUTLANDER PHEV display

ScreenCauseSolution (Reference)lThere is a fault in the sensor.l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Forward Collision Mitigation
System (FCM): When a problem is detec- ted” on page 7-69.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic High-Beam (AHB):
System problem warning” on page 6-57.l The Forward Collision Mitigation System
(FCM), Lane Departure Warning (LDW)
and automatic high-beam system are tem-
porarily unavailable due to a high or low temperature of the sensor.l After the temperature of the sensor has
been in range, the system will automati-
cally return to operation.
Refer to “Forward Collision Mitigation System (FCM): When a problem is detec-
ted” on page 7-69.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-87.
Refer to “Automatic High-Beam (AHB): System problem warning” on page 6-57.l The sensor is temporarily unavailable due
to conditions such as the adhesion of con- taminants to the sensor or windscreen.This is not a malfunction.Refer to “Forward Collision Mitigation System
(FCM): When a problem is detected” on page
7-69.
Refer to “Lane Departure Warning (LDW):
System problem warning” on page 7-87.
Refer to “Automatic High-Beam (AHB): Sys-
tem problem warning” on page 6-57.
Indication lamp, warning lamp, and information screen display list
6-39OGGE18E1Instruments and controls6

ScreenCauseSolution (Reference)lThere is a fault in the Automatic High-
Beam (AHB).l We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Automatic High-Beam (AHB): System problem warning” on page 6-57.

Navigation information dis-
play*
E00531401061
On vehicles equipped with MITSUBISHI
Multi-Communication System (MMCS), the following information on navigation will be
displayed when guidance location such as junction and destination is approached afteryou set the destination and started the route
guidance.
1- Guidance displayShows the direction of vehicle travel and the guidance location.
Indication lamp, warning lamp, and information screen display list
6-40OGGE18E1Instruments and controls6 Direction of vehicle travel (Example) Destination Ferry terminal Tollbooth Intermediate destination (Example)

2- Remaining distance displayShows the distance to the location where
the guidance is displayed.NOTEl Please read this section and also the separate
owner’s manual for MITSUBISHI Multi-
Communication System (MMCS).Other interrupt displays
E00524202338
ScreenSystem operation statusReferencel When you pressed the power switch and
the operation mode become the ACC
without depress the brake pedal, this
screen is displayed.
This screen will be displayed repeatedly at regular intervals while the operation mode of the power switch is put in ACC.l Place the select position in the “P” (PARK)
position, depress the brake pedal more
firmly than usual with the right foot. Then,
press the power switch.
Refer to “Starting and stopping the Plug-in Hybrid EV System” on page 7-14.l When Plug-in Hybrid EV System does
not start even if the operation mode of the power switch is put in ON, this screen is displayed.l When starting the Plug-in Hybrid EV Sys-
tem, you pressed the power switch with- out select position in the “P” (PARK) po-
sition.l Place the select position in the “P”
(PARK) position by pressing the electrical
parking switch, depress the brake pedal more firmly than usual with the right foot.
Then, press the power switch.
Refer to “Starting and stopping the Plug- in Hybrid EV System” on page 7-14.
Indication lamp, warning lamp, and information screen display list
6-41OGGE18E1Instruments and controls6

ScreenSystem operation statusReferencelDriving power is restricted by the safety
system as the Plug-in Hybrid EV System
has become too hot or too cold.l You do not have to take any actions. The
restriction on the driving power will be re- leased when the Plug-in Hybrid EV Sys- tem returns to the normal temperature.l If the vehicle had not been refueled about
15 litres or more at one time for threemonths, the engine starts automatically
for the maintenance of the engine or the fuel system components.
This display may appear frequently de-
pending on the use conditions of your ve- hicle such as when fuel has been staying
in the fuel tank for a long time.
When the engine is running, this display shows the state where the drive battery is
charged, and the battery charge mode dis-
play (
) is displayed. But the
drive battery will not be full charge.
l Refill the 15 litres more at one time. This
display and battery charge mode display will disappear, and the engine will not au- tomatically start for maintenance.
If the fuel remaining display will be be- low half, you can refill the fuel more than
15 litres certainly.
l If you cannot refill the fuel due to the
large amount of remaining fuel, start the engine and drive the vehicle enough to re-duce the fuel level to approximately half
tank.l The accelerator pedal has been depressed
when the select position is in the “N”
(NEUTRAL) position.l When you start the vehicle, be sure to
check the select position indicator and make sure the select position is in the “D”(DRIVE) or “R” (REVERSE) position.
Then, please depress the accelerator ped-
al.
Refer to “Select position indicator” on page 7-17.
Indication lamp, warning lamp, and information screen display list
6-42OGGE18E1Instruments and controls6

ScreenSystem operation statusReferencelThe selector lever has been operated when
the select position is in “P” (PARK) posi-
tion and the brake pedal is not depressed.l Operate the selector lever while depressed
firmly on the brake pedal.
The operation status of each system is displayed on the information screen. Refer to the appropriate page for the system for further details.
ScreenSystem operation statusReferencel When charging of the drive battery is
completed.l Refer to “Charging” on page 3-02.lWhen the mode is changed by the opera-
tion of the 4WD lock switch or ECO mode
switch.l Refer to “ECO mode switch” on page
6-61.
l Refer to “4WD lock switch” on page
7-21.
l Refer to “When the ECO mode switch is
ON” on page 7-22.
Indication lamp, warning lamp, and information screen display list
6-43OGGE18E1Instruments and controls6

ScreenSystem operation statusReferencelWhen approaching the guidance location,
etc.l Refer to “Navigation information display”
on page 6-40.l When the EV priority mode is activated.l Refer to “EV switch” on page 7-25.lWhen the battery save mode is activated.l Refer to “Battery save mode switch” on
page 7-27.l When the battery charge mode is activa-
ted.l Refer to “Battery charge mode switch” on
page 7-28.
Indication lamp, warning lamp, and information screen display list
6-44OGGE18E1Instruments and controls6

ScreenSystem operation statusReferencelWhen the reversing sensor system detects
an obstruction.l Refer to “Reversing sensor system” on
page 7-94.l When the parking sensors detect an obsta-
cle.l Refer to “Parking sensors (Front/Rear)”
on page 7-98.l When the Forward Collision Mitigation
System (FCM) is activated or the timing of an alarm is changed.l Refer to “FCM and UMS ON/OFF switch”
on page 7-68.l When the Forward Collision Mitigation
System (FCM) is deactivated.l Refer to “FCM and UMS ON/OFF
switch” on page 7-68.l When the Ultrasonic misacceleration Mit-
igation System (UMS) is deactivated.l Refer to “To turn on/off the UMS” on
page 7-79.
Indication lamp, warning lamp, and information screen display list
6-45OGGE18E1Instruments and controls6

ScreenSystem operation statusReferencelWhen the operation mode of the Lane De-
parture Warning (LDW) is switched.l Refer to “Lane Departure Warning
(LDW): How to operate LDW” on page 7-86.
This informs you that a periodic inspection is due.
ScreenSolutionWe recommend you to have it checked. Refer to “Service reminder” for further de-tails on page 6-11.
Indication lamp, warning lamp, and information screen display list
6-46OGGE18E1Instruments and controls6