2018 MITSUBISHI OUTLANDER brake

Adaptive Cruise Control System (ACC) (if so equipped)5-112 Features and controls
5
N00576900036
While the ACC is activated, if your vehicle isapproaching too closely to the vehicle infront, the ACC gives a warning by sounding abuzzer and displaying a message. Apply thebrakes to maintain the appropriate distance tothe vehicle in front.When the vehicle in
front has changed its
course or lane, if a stationary vehicleappears in front you
r vehicle, the ACC
will not decelerate your vehicle.
Approach alarm

WA R N I N GWhen the ACC is not being used, turn offthe system to avoid
unexpected ACC acti-
vation.Never operate the AC
C from outside the
vehicle.WA R N I N G
The ACC will not decelerate your vehicleand/or give the approach alarm in the fol-lowing cases.• When an object other than a vehicle,such as a pedestri
an, is in front.
• When a malfunction is detected in thesystem.
The ACC will not decelerate your vehiclein the following cases, but will give theapproach alarm.• When the front vehicle is stationary ormoving at an extr
emely slow speed.
• When your brake system has a problem,such as overheating.
The ACC may not be able to maintain theset speed or the dist
ance to a vehicle in
front and may not alert the driver, if thesystem cannot detect the front vehicleproperly. Typical situations include: • When a vehicle cuts
into your path at a
close distance.• When a vehicle in front is not completelyin your path.• When a vehicle in front is towing atrailer.• When a motorcycle or a bicycle is infront.• When a vehicle in fr
ont is a truck loaded
with freight that protrudes rearwardfrom the cargo bed.WA R N I N G
• When the height of a vehicle in front isextremely low or the road clearance ofthe vehicle is extremely high.• When driving on a r
oad with alternating
up and down surfaces.• When driving on a curve.• When driving on a bumpy or rough road.• When driving in a tunnel.• When driving in construction zones.• When the rear of your vehicle is weigheddown with the weight of passengers andluggage• For up to two minutes after starting driv-ing.• When driving in curved sections of roadincluding their entrance/outlet or run-ning beside a closed lane in a traffic workor similar zone.• When the surface of th
e sensor is covered
with dirt, snow, ice, etc.• When a front vehicle or an oncomingvehicle is splashing wa
ter, snow or dirt.
WA R N I N G
BK0249100US.book 112 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Adaptive Cruise Control System (ACC) (if so equipped)5-114 Features and controls
5
switch and release the accelerator pedal; thenew speed is then set in the system.
N00581600028
There are two ways to decrease the set speed.The set speed will decrease by 1 mph (1km/h) every time you push down the “SET -”hold the switch pushed down, the set speeddecreases in 5 mph (5 km/h) increments.
By depressing the brake pedal while the ACCis activated, the ACC c
ontrol is canceled and
your vehicle speed will decrease.At the point where the vehicle speed reachesyour desired speed,
push down and release
the “SET -” switch; the new speed is then setin the system.
WA R N I N GThe ACC braking control and approachalarm functions will
not work while the
accelerator pedal is depressed.NOTE
The set speed indicator in the multi informa-tion display will show
“---” while the accel-
erator pedal is depressed.If the “SET -” button is not pushed downwhile depressing the ac
celerator pedal, your
vehicle speed will return to the set speed,after the accelerator pedal is released. Whenthe accelerator pedal is released, the ACCbraking control and approach alarm func-tions may not i
mmediately work.
To decrease the set speed

By using the “SET -” switch:

NOTE
There is some time
lag until the vehicle
begins decelerating after the set speed hasbeen changed.
The set speed can be changed even whileyour vehicle is follow
ing a vehicle in front
using the ACC. In this case, however,although the set speed it
self is decreased,
your vehicle will
not decelerate.
When the switch is held, a buzzer will soundevery time the set speed changes
By using the brake pedal:

NOTE
BK0249100US.book 114 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Adaptive Cruise Control System (ACC) (if so equipped)
Features and controls 5-115
5
N00582800027
Simply depress the accelerator pedal to tem-porarily accelerate the
vehicle. Releasing the
pedal automatically sl
ows down the vehicle
to the set speed and ACC restarts its control.
N00581700061
There are two ways to cancel the ACC con-trol. By pressing the “CANCEL” switch.By depressing the brake pedal.
When the ACC is canceled, the “SET” indi-cator goes off and the following distance indi-cator turns to the ‘standby’ display. The frontvehicle indicator also turns to the ‘standby’display when a front vehicle is detected.
NOTE
The ACC control will
not resume after
releasing the brake pedal.
To temporarily accelerate the vehicle

WA R N I N GThe ACC braking control and approachalarm functions will not work while theaccelerator pedal is depressed.
NOTE
The set speed indication on the display turnsto “---” when the accelerator pedal isdepressed. This indication remains as long asthe pedal is in a depressed position.In certain conditions, th
e braking control and
alarming functions of ACC may not work fora short while after releasing the acceleratorpedal.
To cancel ACC control

NOTE
You can also cancel the ACC control bypressing the “ACC ON/OFF” switch. If thisswitch is pressed while the ACC is “ON”,the ACC will be turned off.
BK0249100US.book 115 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Adaptive Cruise Control System (ACC) (if so equipped)5-116 Features and controls
5
In any of the situations listed below, the ACCcontrol is automatica
lly canceled, a buzzer
sounds and a message is shown in the multi-information display.When your vehicle stops.When the ASC is turned off.While ABS, ASC or TCL is activated.When the selector lever is in a positionother than “D” (DRIVE) and “Ds”(DOWNSHIFT & SPORTY DRIVING).When the parking brake is applied.
When the ACC system determines that itsperformance has been degraded, a buzzer willsound and a message will be displayed in themulti information display.This can occur whenForeign objects, such as dirt, snow or ice,adhere to the surface
of the radar sensor.
In adverse weather conditions, such asrain, snow or sand storms, etc.A front vehicle or an oncoming vehicle issplashing water, snow or dirt.Driving on a nonbusy road with a fewvehicles and obsta
cles in front.
The brake system is
overheating due to
continuous brake control on long down-hill slope.
If the display keeps showing the message,there is a possibility that the ACC has a mal-function. Contact your authorized MitsubishiMotors dealer.When the ACC system
detects an abnormal-
ity in the system, the ACC system will beturned off, a buzzer will sound and a messagewill be displayed in the multi information dis-play. If the message remains after the opera-tion mode has been tu
rned to the “OFF”
position, contact your au
thorized Mitsubishi
Motors dealer.
N00581800059
After the ACC control has been canceled withthe ACC turned on, the ACC control can beresumed by pushing up
and releasing the
“RES +” switch.To resume the control

BK0249100US.book 116 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Forward Collision Mitigation System (FCM) (if so equipped)5-118 Features and controls
5
N00582100046
For vehicles sold in U.S.A. FCC ID:OAYARS3-BThis device complies
with Part 15 of FCC
Rules. Operation is subject to the followingtwo conditions.(1) This device may not cause harmful inter-ference, and(2) this device must
accept any interference
received, including interference that maycause undesired operation.For vehicles sold in Canada IC: 4135A-ARS3BThis device complies with Industry Canadalicence-exempt RSS standard(s). Operation issubject to the following two conditions: (1)this device may not cause interference, and(2) this device must
accept any interference,
including interference
that may cause unde-
sired operation of the device.
N00577300095
The Forward Collision Mitigation System(FCM) is designed to help reduce the risk of acollision with a vehicle or a pedestrianstraight ahead of your vehicle. The FCM usesa sensor (A) to determine the distance andrelative speed to a vehi
cle and a pedestrian in
front. The FCM is not designed as an auto-matic driving system or as a collision avoid-ance system. When your vehicle is approaching a vehicleor a pedestrian strai
ght-ahead in your path
and the FCM judges that there is the risk of acollision, the system
will give audible and
visual warnings.When the FCM judges that a collision withthe vehicle or the pedest
rian straight-ahead is
imminent, the system will automaticallyapply moderate braking to warn you to applythe brakes immediately. When the FCM judges that a collision withthe vehicle or the pedest
rian straight-ahead is
highly unavoidable, th
e system will apply
emergency braking to reduce the severity ofthe collision and, if possible, to avoid the col-lision.Stop lights are illuminated during automaticbraking.
General information

CAUTIONChanges or modifica
tions not expressly
approved by the manufacturer for compli-ance could void the user’s authority to oper-ate the equipment.
Forward Collision Mitiga-tion System (FCM)
(if so
equipped)
BK0249100US.book 118 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Forward Collision Mitigation System (FCM) (if so equipped)
Features and controls 5-119
5
N00577400041
If the system judges that there is a risk ofyour vehicle colliding wi
th a vehicle or the
pedestrian in front, th
is function warns you of
the potential hazard with
visual and audible
alarms.When this function is triggered, a buzzersounds and, at the same time, a “BRAKE”message appears on the information screen ofthe multi-information display.The FCM will also prepare to provide quickbrake response and greater brake force whenyou apply the brakes.The forward collision
warning function oper-
ates when the following vehicle speed:Against a vehicle: Approximately 10 mph(15 km/h) to 87 mph (140 km/h).Against a pedestrian
: Approximately 5
mph (7 km/h) to 40 mph (65 km/h).
WA R N I N GBefore using the FCM, read this entiresection to fully understand the limitationsof this system. Failure to follow instruc-tions could result
in an accident.
The FCM is designed
to help avoid certain
frontal collisions or reduce the crashspeed in such collisions. It is not a substi-tute for your safe and careful driving.Under certain circumstances, the systemmay not operate or may not detect cor-rectly a vehicle or a
pedestrian in front.
When your vehicle is
approaching a vehi-
cle or a pedestri
an too closely, take all nec-
essary actions to avoi
d a collision, such as
braking and
steering, regardless of
whether the FCM is
activated or not.
Never rely on the FCM to prevent a colli-sion.Never attempt to test the operation of theFCM. Doing so could cause an accident,resulting in seriou
s injury or death.
WA R N I N G
Forward collision warning function

BK0249100US.book 119 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Forward Collision Mitigation System (FCM) (if so equipped)5-120 Features and controls
5
N00577700073
When the FCM judges that a collision withthe vehicle or the pedest
rian straight-ahead is
imminent, the FCM will automatically applymoderate braking to warn the driver to applythe brakes immediately.If the FCM judges that the collision is highlyunavoidable, it will automatically applyemergency braking to reduce the severity ofthe collision and, if possible, to avoid the col-lision.When the FCM applies
emergency braking, a
buzzer sounds and a warn
ing message is dis-
played in the information screen of the multi-information display.The FCM braking function operates when thefollowing ve
hicle speed:
Against a vehicle:
Approximately 3 mph
(5 km/h) to 50 mph (80 km/h)mph (5 km/h) to 40 mph (65 km/h)
FCM braking function

WA R N I N GIf the ASC is turned off, the FCM brakingfunction will not operat
e. Refer to “Active
stability control” on page 5-100.If the brake pedal is not depressed within2 seconds after your vehicle has beenstopped by the FCM, a warning buzzerwill sound and the brak
es activated by the
FCM will automatically be released.Apply the brakes as
necessary to keep
your vehicle stationary.The FCM will not ac
tivate and will not
provide either warnin
g or braking in cer-
tain situations. Some of these include:• When the selector lever is in the “P”(PARK) or

Forward Collision Mitigation System (FCM) (if so equipped)5-122 Features and controls
5
N00577800090
This switch is used to turn on or off the FCM,and also to select the distance which will trig-ger the forward colli
sion warning function.
• When a vehicle in the next lane becomespositioned directly in
front of your vehi-
cle due to winding road conditions.• When passing through an area thatobjects may contact th
e vehicle, such as
thick grass, tree br
anches, or a banner.
• When there are patterns on the road thatmay be mistaken for
a vehicle or a pedes-
trian.• When a vehicle cuts into your path in thedetecting range of the sensor.• When an oncoming vehicle is positionedstraight ahead of your vehicle on acurved road.• When the FCM detects a long object car-ried on your vehicle,
such as skies or a
roof carrier.• When driving through fog, steam, smokeor dust.
The FCM should be tuned off if any of fol-lowing situations occur:• When using an automatic car wash.• When the tires are not properly inflated. • When the emergency spare tire is used.WA R N I N G
• When your vehicle is
towed or
your vehi-
cle tows another vehicle.• When your vehicle is
carried on a truck.
• When your vehicle is on a chassis dyna-mometer or free rollers.• If the windshield on or surrounding thesensor is cracked or scratched.NOTE
When depressing the brake pedal while auto-matic braking is applie
d, the brake pedal will
feel firm. This is normal. Depress the brakepedal harder to apply
greater braking force.
During the automatic
braking, operating
sounds may be heard.
This is normal.
WA R N I N G
FCM ON/OFF switch

BK0249100US.book 122 ページ ２０１７年５月１０日　水曜日　午前８時４９分