2018 MITSUBISHI OUTLANDER seats

Making a flat seat
Seat and restraint systems 4-17
4
1. Remove the head restraints from the frontseats and raise the arm rest on the secondrow seats.For vehicles with a cargo area cover,remove the cover.(Refer to “Head restraints” on page 4-11,“Arm rest” on page 4-10 and “Cargo areacover” on page 5-244.)2. Slide the second row seats back as far aspossible (vehicles with second row seatslide function).(Refer to “To adjust the seat forward orbackward” on page 4-8.)
3. Slide the front seats fully forward, thenrecline their seatbacks backward toachieve a flat surface.(Refer to “To adjust the seat forward orbackward” on page 4-5 and “To adjust theseatback” on page 4-6.)4. Recline the seatbacks of the second rowseats.(Refer to “To adjust the seatback” on page4-8.)
plete.To return the seats to the normal position,reverse the above procedure.
To raise the seatback of the front seat, firmlyplace your hand on the
seatback, pull the
seatback lock knob up, and raise the seatbackslowly. (Refer to “To adjust the seatback” onpage 4-6.) Do not let children adjust the seat-back.CAUTION
BK0249100US.book 17 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belts
Seat and restraint systems 4-19
4
N00406201513
All seats are equipped with a seat belt whichuses one combined lap-and-shoulder belt withan emergency locking retractor.This system is designed to provide both com-fort and safety. It perm
its full extension and
automatic retraction of the belts during nor-mal vehicle operation.
A sensing device
inside the belt retractor is designed to lock theretractor in the event of a sudden change inthe vehicle’s motion.
1. Occupants should always
sit back in their
seats with their backs against the uprightseatback. To reduce
the risk of serious
injury or death during deployment of theairbag, adjust the driver’s seat as far backas possible while maintaining a positionthat still enables you to fully apply thepedals, easily control the steering wheel,and safely operate the vehicle. The frontpassenger seat should also be moved asfar back as possible. Refer to “Supple-mental Restraint System (SRS) - airbag”on page 4-35. Also refer to “To adjust theseat forward or backward” on page 4-5.
2. Before using the center seat belt for sec-ond row, make sure that the detachableanchor is securely
latched and the seat
belt is not twisted. For details, refer topage 4-21.
Seat belt instructions
NOTE
For instructions on installing a child restraintsystem using a seat belt
, refer to “Installing a
child restraint system
using the seat belt” on
page 4-32.
WA R N I N GTo reduce the risk of serious injury ordeath in the event of
an accident or sud-
den stop, all seatbacks should be kept inthe upright position while the vehicle is inmotion.Seat belt performance during an accidentcan be adversely affect
ed if the seatbacks
are reclined. The more a seatback isreclined, the more likely seat belt perfor-mance will be advers
ely affected. If the
seat belt is not prop
erly positioned against
the body during an accident, there isincreased risk you will slide under the beltand receive serious
injury or death.
BK0249100US.book 19 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belts4-24 Seat and restraint systems
4
N00406301354
The seat belt shoulder
anchor height can be
adjusted. To move the anchor down, press thelock knob (A) and slide the anchor down tothe desired position. To move the anchor up,slide the anchor up to the desired position.
N00406501112
When seat belts for the second row outboardseating position and for the third row are notused, the seat belts can be stored.
WA R N I N GWhen a child booster se
at is used on the
front passenger seat, the front passengerseat belt warning ligh
t will not come on, if
the seat belt is not fastened when thebooster seat is used
. Confirm that the
child is wearing the
seat belt properly.
Do not install any acce
ssory or sticker that
makes the light difficult to see.
Adjustable seat belt shoulder anchor (front seats) Anchor down Anchor up
WA R N I N GAlways adjust the shou
lder belt anchor so
that the shoulder belt
is positioned across
the center of your shoulder without touch-ing your neck. The sh
oulder belt should
not be able to fall off your shoulder. Fail-ure to follow this instruction can adverselyaffect seat belt performance and increasethe risk of serious in
jury or death in the
event of an accident.Adjust the shoulder be
lt anchor only when
the vehicle is not in motion.Make sure the anchor is securely locked inposition after adjusting it.
Storing the second row (out-board seating positions) and third row seat belts
BK0249100US.book 24 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belt use during pregnancy
Seat and restraint systems 4-25
4
Put the seat belt webbing in the back slot (A)on the clip and insert the metal plate of thelatch plate into the front slot (B) as shown inthe illustration.
N00406701202
If your seat belt is not long enough, evenwhen fully extended,
a seat belt extender
must be obtained. The extender may be usedfor either of the front seats.
N00406800134
Seat belts work for everyone, including preg-nant women. Like a
ll occupants, pregnant
women are more likely to be seriously injuredor killed in an accident if they do not wearseat belts.
N00417701710
The driver’s and front passenger’s seats eachhave a seat belt
equipped with a pre-tensioner
system and force limiter system.
Seat belt extender
WA R N I N GThe extender should only be used if theexisting belt is not long enough. Anyonewho can use the standard seat belt shouldnot use an extender. Unnecessary use of anextender can adversel
y affect seat belt
performance in an accident.When not required, the extender must beremoved and stowed.
Seat belt use during preg-nancy
WA R N I N GTo reduce the risk of serious injury ordeath to pregnant women and unbornchildren in an accident, pregnant womenshould always wear
a seat belt. The lap
portion of the seat belt should be wornsnug and low across the hips and belowthe rounding. Consult your doctor if youhave any additional qu
estions or concerns.
Seat belt pre-tensioner and force limiter systems
BK0249100US.book 25 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-27
4
N00408701147
This warning light tells you if there is a prob-lem involving the SRS airbags and/or the seatbelt pre-tensioner system. Refer to “SRSwarning light/display” on page 4-41.
N00408900126
In the event of an accident, the seat belt forcelimiter system will help reduce the forceapplied to the driver a
nd front seat passenger.
N00407101740
When transporting infants or small childrenin your vehicle, an appr
opriate child restraint
system must always be
used. This is required
by law in the U.S. and Canada.Child restraint systems specifically designedfor infants and small children are offered byseveral manufacturers. Choose only a childrestraint system with a label certifying that itcomplies with Federal Motor Vehicle SafetyStandard 213 (FMVSS 213) or Motor VehicleRestraint Systems and
Booster Seats Safety
Regulations (RSSR).
Look for the manufac-
turer’s statement of compliance on the boxand child restraint system itself.
The child restraint system should be appropri-ate for your child’s we
ight and height, and
should properly fit your vehicle’s seat.For detailed information,
refer to the instruc-
tion manual accompanying the child restraintsystem.All children should be properly restrained ina restraint device that offers the maximumprotection for their size and age.Be sure to check local,
state, or provincial
requirements for child size and age that mayvary from the recommendations listed below.Children less than 1 year old and whoweigh 22 pounds (10 kg) or less MUSTride in a rear-facing child safety seat thatMUST ONLY be used in the second rowseat.Children older than 1 year of age and whoweigh less than 40 pounds (18 kg) or whoare less than 40 inches (100 cm) tall mustbe in a forward-facing restraint used onlyin the rear seat.
Children who weigh more than 40 pounds(18 kg) or who are more than 40 inches(100 cm) tall, regardless of age, shoulduse a suitable child seat or a booster seatin the rear seat until the vehicle’s lap-and-shoulder belt fits
them properly.
SRS warning Force limiter system Child restraint systems
Guidelines for child restraint system selection
WA R N I N GAll children must be seated in the rearseat, and properly restrained.Accident statistics
show that children of
all sizes and ages are safer when properlyrestrained in the rear seat, rather than inthe front seat.Be sure to select a child restraint systemthat is appropriate not only for the child’ssize and age but also for your vehicle.Some child restraint systems may not fityour vehicle properly.
BK0249100US.book 27 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems4-28 Seat and restraint systems
4
Any child who is too large to use a childrestraint system should ride in the rearseat and wear the la
p-and-shoulder belt
properly. The shoulder belt must be posi-tioned over the shou
lder and across the
chest, not across their neck, and with thelap belt positioned low on the child’s hips,not across their stomach. If necessary, abooster seat should be
used to help achieve
a proper seat belt fi
t. Follow the booster
seat manufacturer’s instructions. Only usea booster seat that is
certified as comply-
ing with Federal Motor Vehicle SafetyStandards or Motor Vehicle Restraint Sys-tems and Booster Seats Safety Regula-tions. WA R N I N G
WA R N I N GNever hold an infant
or child in your arms
or on your lap when ri
ding in this vehicle,
even when you are wearing your seat belt.Never place any part of the seat belt youare wearing around an
infant or child.
Failure to follow these simple instructionscreates a risk of serious injury or death toyour child in the even
t of an accident or
sudden stop.
WA R N I N GYour vehicle is also equipped with a frontpassenger’s airbag.Never put REAR-FACING CHILDRESTRAINT SYSTEMS or INFANTRESTRAINT SYSTEMS in the front pas-senger seat. This places the infant tooclose to the passenger’s airbag. Duringdeployment of that airbag, the infant canbe seriously injured
or killed.
Rear-facing
child restraint systems or infant restraintsystems must only be used in the rear seat.Airbag
BK0249100US.book 28 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems4-30 Seat and restraint systems
4
N00418801167
The outboard seating pos
itions in the second
row seat of your vehicle are equipped withlower anchors for attaching child restraintsystems compatible with the LATCH system.
N00418901201
Your vehicle has 3 at
tachment points on the
backside of the second
row seats. These are
for securing a child restraint system tetherstrap to each of the 3 rear seating positions inyour vehicle.
N00419000198N00419101301
1. In order to securely
fasten the tether strap,
remove the head restraint from the loca-tion where you wish to install the childrestraint system.2. Open the gap a little between the seatcushion (A) and the seatback (B) withyour hand to locate the lower anchors (C).
Installing a child restraint sys-tem using the LATCH (Lower Anchors and Tethers for chil-dren) system Lower anchor locations
NOTE
The symbols on the seatback show the loca-tion of the lower anchor points.
Tether anchor locations
Examples of child restraint sys-tems compatible with the LATCH system A- Rear-facing child restraint systemB- Front-facing child restraint systemC- Child restraint system lower anchor
connectors
D- Tether strap
(These are only examples.)
Using the LATCH system
BK0249100US.book 30 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-31
4
3. For easier access, the seatback may berecline rearward.Push the anchor connectors (D) on thechild restraint system into the loweranchors (C) in accordance with theinstructions provided by the child restraintsystem’s manufacturer.After it is security fastened, adjust theseatback to 4 steps forward from mostreclined position.Remember, the lower anchors (C) pro-vided with your vehi
cle are designed to
secure suitable child restraint systemscompatible with the LATCH system inthe outboard positions of the secondrow seats only. The anchor connectorsare NOT designed to secure a suitablechild restraint system in the middleseating position of the second row seat.
4. Latch the tether strap hook (E) of the childrestraint system to the tether anchor bar(F) and tighten the tether strap so it issecurely fastened.5. Push and pull the chil
d restraint system in
all directions to ensure it is firmlysecured.
A- Vehicle seat cushionB- Vehicle seatbackC- Lower anchor
D- Connector
NOTE
In order to secure a child restraint systemcompatible with the LATCH system, use thelower anchor points in the outboard positionsof the second row seat. It is not necessary touse the vehicle’s seat
belt. The vehicle’s seat
belt, however, MUST be
used to secure a
child restraint system in the middle seatingposition of the second row seat.WA R N I N GIf there is any foreign material in oraround the lower an
chors, remove it
before installing the child restraint sys-tem. Also, make sure the seat belt is awayfrom, not looped through or otherwiseinterfering with, the child restraint sys-tem. If foreign matter is not removedand/or the seat belt
interferes with the
child restraint system, the child restraintsystem will not be secured properly, coulddetach and move forw
ard in the event of
sudden braking or an
accident, and could
result in injury to the child or other vehi-cle occupants.When the vehicle is
moving, do not adjust
the seat where the child restraint system isinstalled.
NOTE
If it is difficult to
latch the tether strap hook,
turn the hook sideways.WA R N I N GChild restraint system tether anchors aredesigned only to with
stand loads from cor-
rectly fitted child restraint systems. Underno circumstances are they to be used foradult seat belts, harnesses, for attachingother items, or equipment to the vehicle.
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分