2018 MITSUBISHI OUTLANDER display

Forward Collision Mitigation System (FCM) (if so equipped)
Features and controls 5-123
5
Every time the opera
tion mode is put in
“ON”, the FCM will automatically be turnedon.To turn off the FCM, press and hold the FCMON/OFF switch. The following message and
indicator will appear in the multi-infor-
mation display.To turn on the FCM again, press and hold theFCM ON/OFF switch. The indicator willgo off, and a current
distance mode for the
forward collision warning will be shown inthe multi-information display.
The distance to the vehicle ahead which trig-gers the forward collision warnings can beselected from three levels, “FAR”, “MID-DLE” or “NEAR”.To change the distance mode, press the FCMON/OFF switch. Every time the switch ispressed, the distance mode will be switched.The selected distance mode is shown on theinformation screen of the multi-informationdisplay. When “FAR” is selectedWhen “MIDDLE” is selected
When “NEAR” is selected
N00593300035
When the FCM system determines that itsperformance has been degraded, the FCMwill become inoperative.This can occur whenForeign objects, such
as dirt, snow, ice,
mist or dew condensat
ion adhere to the
windshield of the sensor portion.In adverse weather conditions, such asrain, snow, sand storms, etc.A front vehicle or an oncoming vehicle issplashing water, snow or dirt.
To turn on/off the FCM

To change forward collision warn-ing distance

NOTE
Actual distance which triggers the forwardcollision warnings w
ill vary depending on
your vehicle speed a
nd the front vehicle
speed. The distance will become longerwhen the vehicle speeds are higher.The distance which will trigger the FCMbraking function cannot be adjusted.
When a problem is detected

BK0249100US.book 123 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Forward Collision Mitigation System (FCM) (if so equipped)5-124 Features and controls
5
“DRIVER ASSISTANCE CAMERABLOCKED” message will appear and the indicator will appear on the informationscreen of the multi-information display.When the sensor performance returns, theFCM functions will resume operation.If the message continues
showing, there is a
possibility that the se
nsor has a malfunction.
Contact an authoriz
ed Mitsubishi Motors
dealer for inspection of the sensor.
If the system becomes temporarily unavail-able for some reason, the following messagemay appear.The indicator will appear on the informa-tion screen of the multi-information displayand the FCM will automatically be turned off.If the message continues showing, there is apossibility that the
FCM has a malfunction.
Contact an authorized Mitsubishi Motorsdealer for inspection of the system.
If the system becomes temporarily unavail-able due to the high or low temperature of thesensor, the following
message will appear.
The indicator will appear on the informa-tion screen of the mu
lti-information display
and the FCM will automa
tically be turned off.
After the temperature of
the sensor has been
in range, the system will automatically returnto operation.If the message continues
showing, there is a
possibility that the FCM has a malfunction.Contact an authoriz
ed Mitsubishi Motors
dealer for inspection of the sensor.
NOTE
The “DRIVER ASSI
STANCE CAMERA
BLOCKED” message may temporarilyappear on the information screen when thesensor cannot detect a
vehicle, a pedestrian
or an object within ra
nge. This is not a mal-
function. When a vehicle or an object comeswithin range, the FCM function will resumeand the message will go off.
The “DRIVER ASSISTANCE CAMERABLOCKED” message may appear on theinformation screen when driving on a non-busy road with a few
vehicles and obstacles
in front.NOTE
BK0249100US.book 124 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Forward Collision Mitigation System (FCM) (if so equipped)
Features and controls 5-125
5
If the FCM detects a malfunction in the sys-tem, either of the following messages willappear, the indicator
will appear on the
information screen of
the multi-information
display and the FCM will automatically beturned off.If the message remains even after the opera-tion mode is put in “OFF” and then turnedback to “ON”, please contact your authorizedMitsubishi Motors dealer.
N00593400049
The sensor (A) is lo
cated inside the wind-
shield as shown in the illustration.The sensor is shared in the following sys-tems:FCMLane Departure Warning (LDW)Automatic high beam system
NOTE
If the sensor or its surrounding area becomesextremely high temperature when parkingthe vehicle under a blazing sun, the “FCMSERVICE REQUIRED” message mayappear.After the temperature of the sensor or its sur-rounding area has been in range, if the mes-sage remains even afte
r restarting the engine,
please contact an au
thorized Mitsubishi
Motors dealer.
Handling of the sensor

CAUTIONTo maintain proper performance of the FCM,LDW and Automatic high beam system;• Always keep clea
n the windshield.
If the inside of the windshield where thesensor is installed be
comes dirty or fogged,
contact an authorized Mitsubishi Motorsdealer.• Do not apply an impact or load on the sen-sor or its surrounding area.
BK0249100US.book 125 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Blind Spot Warning (BSW) (with Lane Change Assist) (if so equipped)
5
N00592700032
When the warning display appears, the BSWdoes not operate normally because there aresome malfunctions in the system or the sen-sor. Have the vehicle
inspected at an autho-
rized Mitsubishi Motors dealer as soon aspossible.
N00592800033
When the warning displa
y appears, the sensor
is temporarily not available for some reasonsuch as the environmental condition orincrease of the sensor temperature. When thewarning display does
not disappear after
waiting for a while, contact an authorizedMitsubishi Motors dealer.
N00592900034
When the warning display appears, the radarsensor cannot detect
a vehicle traveling side
by side or an approaching vehicle, becauseforeign objects, such as dirt, snow or ice,adhere to the bumper surface around the sen-sor.Remove a dirt, freezing
or foreign material on
the bumper surface around the sensor.When the warning display does not disappearafter having cleaned the bumper surfacearound the sensor, contact an authorized Mit-subishi Motors dealer.
When there is a malfunction in the system or the sensor

NOTE
When the warning display appears, the BSWwill be deactivated.
When the sensor is temporarily not available

When there is a foreign objects on the sensor

BK0249100US.book 130 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Rear Cross Traffic Alert
(RCTA) (if so equipped)
Features and controls 5-131
5
N00593900044
For vehicles sold in U.S.A. FCC ID:OAYSRR3AThis device complies with Part 15 of FCCRules. Operation is subject to the followingtwo conditions:(1) This device may not
cause harmful inter-
ference, and(2) this device must
accept any interference
received, including interference that maycause undesired operation.For vehicles sold in Canada Applicable law: Canada 310This device complies with Industry Canadalicence-exempt RSS sta
ndard(s). Operation is
subject to the following two conditions: (1)this device may not ca
use interference, and
(2) this device must accept any interference,including interference that may cause unde-sired operation of the device. Frequency bands: 24.05 - 24.25GHz Output power: less than 20 milliwatts
N00593000045
The Rear Cross Traffic Alert (RCTA) is anaid system for backing up. When the RCTAsystem detects vehicl
es approaching from
sides while your vehicle is reversing, theBlind Spot Warning lights in outside rearviewmirrors on both sides w
ill blink and a buzzer
will sound to alert the driver. A warning mes-sage will also appear on the informationscreen of the multi-information display.
General information

CAUTIONChanges or modifica
tions not expressly
approved by the manufacturer for compli-ance could void the user’s authority to oper-ate the equipment.
Rear Cross Traffic Alert (RCTA)
(if so equipped)
WA R N I N GBefore using the RCTA, read this entiresection to fully understand the limitationsof this system. Failure to follow instruc-tions could result
in an accident.
BK0249100US.book 131 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Rear Cross Traffic Alert
(RCTA) (if so equipped)
Features and controls 5-133
5
1. Press the Blind Spot Warning switchwhile the operation mode is put in ON.(Refer to “Blind Spot Warning (BSW): Tooperate” on page 5-128.)2. When the selector lever is moved to the“R” (REVERSE) position, the RCTA willoperate.
If the system detects a problem, a warning isdisplayed on the information screen in themulti-information display.Refer to

Lane Departure Warning System (LDW) (if so equipped)5-134 Features and controls
5
N00577900059
The Lane Departure Wa
rning system (LDW)
tentional lane departure. The LDW isdesigned to read lane markers by using a sen-sor (A) under certain
conditions. The LDW
will give you both visual and audible warn-ings when your vehicle is leaving or has leftthe lane.
N00595000023
From the factory, the LDW mode of yourvehicle is set to LDW 1 meaning that everytime the ignition switch is turned to the “ON”the LDW will automatically be activated.The “LDW” indicator will appear on theinformation screen of the multi informationdisplay,You can set your vehi
cle to LDW 2. This
means that your vehicle, every time the igni-tion switch is turned to the “ON” position orthe operation mode is put in ON, will alwaysuse the LDW mode that was being used at thetime the vehicle ignition switch was turned tothe “OFF” position or the operation modewas put in OFF.To set the LDW mode:1. Press the LDW switch to turn off theLDW system.
Lane Departure Warning System (LDW)
(if so equipped)
Never rely solely on the LDW. The LDW isnot a collision avoidance system and is nota substitute for your safe and careful driv-ing.Before using the LDW, read this entiresection to understand the limitations ofthis system. Failure to follow instructionscould result in an accident.
Setting the LDW mode

BK0249100US.book 134 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Lane Departure Warning System (LDW) (if so equipped)
Features and controls 5-135
5
2. Press again and hold the LDW switch formore than 10 seconds.3. When you release the LDW switch, theLDW mode is changed and it appears onthe multi information display. or
N00581000051
To turn off the LDW, press the LDW switch.The “LDW” indicator on the informationscreen of the multi-information display willthen go out.To return the LDW to “ON”, press the LDWswitch again.
N00581100036
The LDW, when turned ON, is capable ofrecognizing the lane in which your vehicle istravelling and issuing an audible warningwhen your vehicle begins to leave that travellane. When operating, the “LDW” indicatoron the multi-information display will bechanged to indicator (green). The LDWwill not operate, how
ever, and the “LDW”
conditions have occurred:The vehicle speed is less than 38 mph (60km/h).The turn signal lever is being operated orhas been operated in the past 7 seconds.The hazard warning light is being oper-ated or has been operated in the past 7seconds.
N00581200040
While the “LDW” indicator in the informa-tion display is lit in gr
een, if your vehicle is
leaving or has left the lane, a buzzer willsound intermittently, “LANE DEPARTURE”will appear in the information display andthe indicator will be flashing in amber.
Turning off the LDW

Operation of the LDW

Lane departure warning

BK0249100US.book 135 ページ ２０１７年５月１０日　水曜日　午前８時４９分