2018 MITSUBISHI OUTLANDER III belt

Seat belts4-22 Seat and restraint systems
4
3. Pull the small latch plate (A) slowly andinsert it into the detachable anchor plateuntil a click is heard. Make sure that theseat belt is not twisted.
1. While holding the seat belt, insert a metalplate, such the latch plate of the seat beltor a key, into the slit (E) on the detachableanchor (C) and release the center seat beltfrom the detachable anchor.2. Retract the seat belt slowly by holding theseat belt.
3. After the seat belt has retracted com-pletely, insert the latch plate (B) into theupper slit (F), and then insert the smalllatch plate (A) into the lower slit (G).4. Store the detachable anchor in the storagepocket on the seatback.
NOTE
If the seat belt locks
up and cannot be pulled
out, pull it once with force and let it retractall the way.Then, pull the belt out
slowly once again.
The seat belt can be
buckled up by inserting
the latch plate (B) in
to the buckle (D) like
other seat belts.If the seat belt switch to the ALR childrestraint installation
function and cannot be
pulled out, detach the
latch plate (B) and
move the second row seat fully backward.Refer to “Installing a child restraint systemusing the seat be
lt” on page 4-32.
To d e t a c h
NOTE
If the seat belt is not held, the seat belt willrapidly retract. This
could cause damage to
the interior trim.
BK0249100US.book 22 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belts
Seat and restraint systems 4-23
4
N00418401394
A tone and warning light are used to remindthe driver to fasten the seat belt.If the ignition switch is turned to the “ON”without the driver’s seat belt being fastened, a
warning light will co
me on and a tone will
sound for approximately
6 seconds to remind
you to fasten your seat belt.If the vehicle is driven with the seat belt stillunfastened, the warning light will blink andthe tone will sound inte
rmittently until the
seat belt is fastened. At the same time, “FAS-TEN SEAT BELT” is displayed on the infor-mation screen in the multi informationdisplay (Type 1 only).
N00418301247
The front passenger seat
belt warning light is
located in the instrument panel.When the ignition switch is turned to the“ON” position or the operation mode is put inON, this indicator
normally comes on and
goes off a few seconds later.The light comes on when a person sits on thefront passenger seat bu
t does not fasten the
seat belt. It goes off when the seat belt is sub-sequently fastened.
Driver’s seat belt reminder/warning light and display Type 1Type 2
WA R N I N GIn order to reduce the risk of seriousinjury or death in an
accident, always fas-
ten your own seat belt
. Do not allow any-
one to ride in your ve
hicle unless he or she
is also seated and fastening a seat belt.Children should additi
onally be restrained
in a secure child restraint system.NOTE
If the seat belt subse
quently remains unfas-
tened, the warning li
ght and the tone will
issue further warnings
each time the vehicle
starts moving from a stop.
Front passenger seat belt warn-ing light
BK0249100US.book 23 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belts4-24 Seat and restraint systems
4
N00406301354
The seat belt shoulder
anchor height can be
adjusted. To move the anchor down, press thelock knob (A) and slide the anchor down tothe desired position. To move the anchor up,slide the anchor up to the desired position.
N00406501112
When seat belts for the second row outboardseating position and for the third row are notused, the seat belts can be stored.
WA R N I N GWhen a child booster se
at is used on the
front passenger seat, the front passengerseat belt warning ligh
t will not come on, if
the seat belt is not fastened when thebooster seat is used
. Confirm that the
child is wearing the
seat belt properly.
Do not install any acce
ssory or sticker that
makes the light difficult to see.
Adjustable seat belt shoulder anchor (front seats) Anchor down Anchor up
WA R N I N GAlways adjust the shou
lder belt anchor so
that the shoulder belt
is positioned across
the center of your shoulder without touch-ing your neck. The sh
oulder belt should
not be able to fall off your shoulder. Fail-ure to follow this instruction can adverselyaffect seat belt performance and increasethe risk of serious in
jury or death in the
event of an accident.Adjust the shoulder be
lt anchor only when
the vehicle is not in motion.Make sure the anchor is securely locked inposition after adjusting it.
Storing the second row (out-board seating positions) and third row seat belts
BK0249100US.book 24 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belt use during pregnancy
Seat and restraint systems 4-25
4
Put the seat belt webbing in the back slot (A)on the clip and insert the metal plate of thelatch plate into the front slot (B) as shown inthe illustration.
N00406701202
If your seat belt is not long enough, evenwhen fully extended,
a seat belt extender
must be obtained. The extender may be usedfor either of the front seats.
N00406800134
Seat belts work for everyone, including preg-nant women. Like a
ll occupants, pregnant
women are more likely to be seriously injuredor killed in an accident if they do not wearseat belts.
N00417701710
The driver’s and front passenger’s seats eachhave a seat belt
equipped with a pre-tensioner
system and force limiter system.
Seat belt extender
WA R N I N GThe extender should only be used if theexisting belt is not long enough. Anyonewho can use the standard seat belt shouldnot use an extender. Unnecessary use of anextender can adversel
y affect seat belt
performance in an accident.When not required, the extender must beremoved and stowed.
Seat belt use during preg-nancy
WA R N I N GTo reduce the risk of serious injury ordeath to pregnant women and unbornchildren in an accident, pregnant womenshould always wear
a seat belt. The lap
portion of the seat belt should be wornsnug and low across the hips and belowthe rounding. Consult your doctor if youhave any additional qu
estions or concerns.
Seat belt pre-tensioner and force limiter systems
BK0249100US.book 25 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Seat belt pre-tensioner
and force limiter systems
4-26 Seat and restraint systems
4
The driver and front pa
ssenger seat belts are
equipped with a seat belt pre-tensioner sys-tem. In a moderate-to-severe frontal or sidecollision or when a rollover or overturning ofthe vehicle is detected, the pre-tensioner sys-tem operates simultaneous
ly with the deploy-
ment of the front airb
ags, side airbags or
curtain airbags.The seat belt pre-tensi
oners are located in the
driver’s and front passenger’s seat belt retrac-tors (A) and in the front
passenger se
at’s final
anchor (B). When activated, the pre-tension-ers quickly draw back seat belt webbing andincrease seat belt performance.The seat belt pre-tens
ioner system includes
the following components:
The airbag control unit monitors the readinessof the electronic parts of the system wheneverthe ignition switch or the operation mode isunder the following conditions. These includeall of the items listed
above and all related
wiring.[Except for vehicles
equipped with the
F. A . S . T. - k e y ]The ignition switch is in the “ON” or“START” position. [Vehicles equipped with the F.A.S.T.-key]The operation mode is in ON.
The seat belt pre-tens
ioners will operate
under the same conditions
as the airbag con-
trol unit.When the seat belt pre-tensioners activate,some smoke is released
and a loud noise will
be heard. The smoke is
not harmful, but care
should be taken not to in
tentionally inhale it,
as it may cause some
temporary irritation to
people with respiratory problems.Even in the event of a severe impact, the pre-tensioners will
not operate if the seat belts are
not fastened. The seat be
lt pre-tensioners may
not activate in certai
n collisions, even though
the vehicle may appear
to be severely dam-
aged. Such non-activation does not mean thatsomething is wrong with
the seat belt pre-ten-
sioner system, but rather that the collisionforces were not severe
enough to activate the
system.
Pre-tensioner system
1- SRS warning light2- Front impact sensors3- Seat belt
pre-tensioner
4- Airbag control unit5- Side impact sensors6- Seat belt
buckle switches
WA R N I N GThe seat belt pre-tensioner system isdesigned to work only
once. After the seat
belt pre-tensioners have been activated,they will not work again. They mustpromptly be replaced and the entire seatbelt pre-tensioner system inspected by anauthorized Mitsubis
hi Motors dealer.
BK0249100US.book 26 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-27
4
N00408701147
This warning light tells you if there is a prob-lem involving the SRS airbags and/or the seatbelt pre-tensioner system. Refer to “SRSwarning light/display” on page 4-41.
N00408900126
In the event of an accident, the seat belt forcelimiter system will help reduce the forceapplied to the driver a
nd front seat passenger.
N00407101740
When transporting infants or small childrenin your vehicle, an appr
opriate child restraint
system must always be
used. This is required
by law in the U.S. and Canada.Child restraint systems specifically designedfor infants and small children are offered byseveral manufacturers. Choose only a childrestraint system with a label certifying that itcomplies with Federal Motor Vehicle SafetyStandard 213 (FMVSS 213) or Motor VehicleRestraint Systems and
Booster Seats Safety
Regulations (RSSR).
Look for the manufac-
turer’s statement of compliance on the boxand child restraint system itself.
The child restraint system should be appropri-ate for your child’s we
ight and height, and
should properly fit your vehicle’s seat.For detailed information,
refer to the instruc-
tion manual accompanying the child restraintsystem.All children should be properly restrained ina restraint device that offers the maximumprotection for their size and age.Be sure to check local,
state, or provincial
requirements for child size and age that mayvary from the recommendations listed below.Children less than 1 year old and whoweigh 22 pounds (10 kg) or less MUSTride in a rear-facing child safety seat thatMUST ONLY be used in the second rowseat.Children older than 1 year of age and whoweigh less than 40 pounds (18 kg) or whoare less than 40 inches (100 cm) tall mustbe in a forward-facing restraint used onlyin the rear seat.
Children who weigh more than 40 pounds(18 kg) or who are more than 40 inches(100 cm) tall, regardless of age, shoulduse a suitable child seat or a booster seatin the rear seat until the vehicle’s lap-and-shoulder belt fits
them properly.
SRS warning Force limiter system Child restraint systems
Guidelines for child restraint system selection
WA R N I N GAll children must be seated in the rearseat, and properly restrained.Accident statistics
show that children of
all sizes and ages are safer when properlyrestrained in the rear seat, rather than inthe front seat.Be sure to select a child restraint systemthat is appropriate not only for the child’ssize and age but also for your vehicle.Some child restraint systems may not fityour vehicle properly.
BK0249100US.book 27 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems4-28 Seat and restraint systems
4
Any child who is too large to use a childrestraint system should ride in the rearseat and wear the la
p-and-shoulder belt
properly. The shoulder belt must be posi-tioned over the shou
lder and across the
chest, not across their neck, and with thelap belt positioned low on the child’s hips,not across their stomach. If necessary, abooster seat should be
used to help achieve
a proper seat belt fi
t. Follow the booster
seat manufacturer’s instructions. Only usea booster seat that is
certified as comply-
ing with Federal Motor Vehicle SafetyStandards or Motor Vehicle Restraint Sys-tems and Booster Seats Safety Regula-tions. WA R N I N G
WA R N I N GNever hold an infant
or child in your arms
or on your lap when ri
ding in this vehicle,
even when you are wearing your seat belt.Never place any part of the seat belt youare wearing around an
infant or child.
Failure to follow these simple instructionscreates a risk of serious injury or death toyour child in the even
t of an accident or
sudden stop.
WA R N I N GYour vehicle is also equipped with a frontpassenger’s airbag.Never put REAR-FACING CHILDRESTRAINT SYSTEMS or INFANTRESTRAINT SYSTEMS in the front pas-senger seat. This places the infant tooclose to the passenger’s airbag. Duringdeployment of that airbag, the infant canbe seriously injured
or killed.
Rear-facing
child restraint systems or infant restraintsystems must only be used in the rear seat.Airbag
BK0249100US.book 28 ページ ２０１７年５月１０日　水曜日　午前８時４９分

Child restraint systems
Seat and restraint systems 4-31
4
3. For easier access, the seatback may berecline rearward.Push the anchor connectors (D) on thechild restraint system into the loweranchors (C) in accordance with theinstructions provided by the child restraintsystem’s manufacturer.After it is security fastened, adjust theseatback to 4 steps forward from mostreclined position.Remember, the lower anchors (C) pro-vided with your vehi
cle are designed to
secure suitable child restraint systemscompatible with the LATCH system inthe outboard positions of the secondrow seats only. The anchor connectorsare NOT designed to secure a suitablechild restraint system in the middleseating position of the second row seat.
4. Latch the tether strap hook (E) of the childrestraint system to the tether anchor bar(F) and tighten the tether strap so it issecurely fastened.5. Push and pull the chil
d restraint system in
all directions to ensure it is firmlysecured.
A- Vehicle seat cushionB- Vehicle seatbackC- Lower anchor
D- Connector
NOTE
In order to secure a child restraint systemcompatible with the LATCH system, use thelower anchor points in the outboard positionsof the second row seat. It is not necessary touse the vehicle’s seat
belt. The vehicle’s seat
belt, however, MUST be
used to secure a
child restraint system in the middle seatingposition of the second row seat.WA R N I N GIf there is any foreign material in oraround the lower an
chors, remove it
before installing the child restraint sys-tem. Also, make sure the seat belt is awayfrom, not looped through or otherwiseinterfering with, the child restraint sys-tem. If foreign matter is not removedand/or the seat belt
interferes with the
child restraint system, the child restraintsystem will not be secured properly, coulddetach and move forw
ard in the event of
sudden braking or an
accident, and could
result in injury to the child or other vehi-cle occupants.When the vehicle is
moving, do not adjust
the seat where the child restraint system isinstalled.
NOTE
If it is difficult to
latch the tether strap hook,
turn the hook sideways.WA R N I N GChild restraint system tether anchors aredesigned only to with
stand loads from cor-
rectly fitted child restraint systems. Underno circumstances are they to be used foradult seat belts, harnesses, for attachingother items, or equipment to the vehicle.
BK0249100US.book 31 ページ ２０１７年５月１０日　水曜日　午前８時４９分