2018 MITSUBISHI L200 brake

CAUTIONlWhen
indication lamp blinks, Active Sta-
bility Control function or active traction con-
trol function is operating, which means that
the road is slippery or that your vehicle’s
wheels are beginning to slip. If this happens, drive slower with less accelerator input.
l If an abnormal condition occurs in the sys-
tem while driving, the
indication lamp
will illuminate.
In these cases, follow these procedures:
• If the temperature in the braking system
continues to increase due to continuous
brake control on a slippery road surface,
the
indication lamp will blink, and op-
eration of the active traction control func-
tion will be suspended to protect the brake
system. (The engine control of the active traction control function and normal brake
operation will not be affected.) Park your vehicle in a safe place. When the tempera-
ture in the braking system has come
down, the
indication lamp will go off
and the Active Stability Control function and active traction control function willstart operating again.
CAUTION• If the indication lamp does not go out
even though the above procedure is fol-
lowed, there could be a problem in the system.
Stop the engine and start the engine again
and check whether the
indication lamp
goes out. If the indication lamp goes out, there is no abnormal condition.
If the
indication lamp illuminates even
after your vehicle is driven a short dis-
tance after re-starting the engine, we rec-
ommend you to have your vehicle checked as soon as possible.
l If the vehicle is towed with the ignition
switch in the “ON” position or the operation
mode in ON and only the front wheels or on- ly the rear wheels raised off the ground, the
ASTC may operate, resulting in an accident.
When towing the vehicle with the front wheels raised, keep the ignition switch in the “LOCK” or “ACC” position or the operation
mode in ACC or OFF. When towing the ve-
hicle with the rear wheels raised, keep the ignition switch in the “ACC” position or theoperation mode in ACC.
Refer to “Towing” on page 8-23.
Trailer Stability Assist
(TSA) E00639500033
The trailer stability assist system helps safelyrunning while towing a trailer by controllingthe braking force of each wheel and enginepower in order to stabilize the motion when
detecting the continuous sway of the vehicle
caused by a trailer.
When the trailer stability assist system oper- ates the brakes, the brake lamp turns on.
About the towing of the trailer, refer to page
6-84.
Trailer Stability Assist (TSA)
6-62OKTE18E1Starting and driving6

CAUTIONlDo not over-rely on TSA system.
Due to the slippery road surface, heavy side wind, inappropriate weight and positioning
of luggage, and/or driving at high speed,
TSA system may fail to secure the stability. Always drive appropriately in accordance with the condition of traffic, road surface condition, weather, and the weight and posi-tioning of luggage.
l The trailer stability assist system does not
operate in case as follows:
• When sudden braking and braking while
driving downhill cause an abrupt motion
of the vehicle which makes the vehicle and the trailer form a dogleg shape.
• When a sideslip occurs by sudden steer-
ing.NOTEl When TSA system operates, the vehicle
body may vibrate and the operating sounds
from the engine compartment may be heard.
These motions indicate normal operation of
the system, not abnormal operation.
l TSA system operates when the vehicle speed
is about 55 km/h (34 mph) or higher.
l When TSA system operates, the ASC opera-
tion indication lamp blinks on and off.
l When ASC does not work, TSA system does
not operate.Cruise control*
E00609102395
Cruise control is an automatic speed control system that keeps a set speed. It can be acti-vated at approximately 40 km/h (25 mph) or
more.CAUTIONl When you do not wish to drive at a set
speed, turn off the cruise control for safety.
l On vehicles with
M/T, do not move the
gearshift lever to the “N” (Neutral) position while driving at a set speed without depress-
ing the clutch pedal. The engine will run too
fast and might be damaged.
l Do not use cruise control when driving con-
ditions will not allow you to stay at the same speed, such as in heavy traffic or on roadsthat are winding, icy, snow-covered, wet,
slippery, on a steep downhill slope.NOTEl Cruise control may not be able to keep your
speed on uphills or downhills.
l Your speed may decrease on a steep uphill.
You may use the accelerator pedal if you
want to stay at your set speed.
l Your speed may increase to more than the
set speed on a steep downhill. You must use the brake to control your speed. As a result, the set speed driving is deactivated.Cruise control switches
E00624101184
A- CRUISE CONTROL ON/OFF switch
Used to turn on and off the cruise control.
B- SET - switch
Used to reduce the set speed and to set the
desired speed.

Cruise control*
6-63OKTE18E1Starting and driving6 Type 1 Type 2

To decrease the set speed
E00609501770
There are 2 ways to decrease the set speed.
SET - switch
Push down and hold the SET - switch (B) while driving at the set speed, and your speed
will slow down gradually.
When you reach your desired speed, release the switch. Your new cruising speed is nowset.
To slow down your speed in small amounts,
push down the SET - switch (B) for less than approximately 1 second and release it.
Each time you push down the SET - switch (B), your vehicle will slow down by approxi-
mately 1.6 km/h (1 mph).
Brake pedal
While driving at the set speed, use the brake
pedal, which disengages the cruise control,
then push down the SET - switch (B) and re-
lease the switch momentarily to set a new de- sired cruising speed.Cruise control*
6-66OKTE18E1Starting and driving6Type 1 Type 2 Type 1 Type 2

To temporarily increase or de-crease the speed
E00609601348
To temporarily increase the speed
Depress the accelerator pedal as you would
normally. When you release the pedal, you will return to your set speed.
To temporarily decrease the
speed
Depress the brake pedal to decrease the speed. To return to the previously set speed,
push up the RES + switch (C).
Refer to “To resume the set speed” on page
6-68.To deactivate
E00609702795
The set speed driving can be deactivated as
follows:
l Press the CRUISE CONTROL ON/OFF
switch (A) (Cruise control will be turned off.)
l Press the CANCEL switch (D).
l Depress the brake pedal.
The set speed driving is deactivated automat-
ically in any of the following ways.
l When you depress the clutch pedal (on
vehicles with M/T).
l When your speed slows to approximate-
ly 15 km/h (9 mph) or more below the set speed because of a hill, etc.
Cruise control*
6-67OKTE18E1Starting and driving6 Type 1 Type 2 Type 1 Type 2

Under either of the following conditions,however, using the switch does not allow you
to resume the previously set speed. In these
situations, repeat the speed setting procedure:
l The CRUISE CONTROL ON/OFF
switch is pressed.
l The ignition switch is turned OFF or the
operation mode is put in OFF.
l Indication lamp go off.Speed Limiter
E00633201110
The Speed Limiter is a driver assist functionto prevent from exceeding the speed set by
driver while engine power control.
CAUTIONl Because the system does not use service
brake (hydraulic brake), the vehicle speed may exceed the set speed on the downhill.
If a driver wants to keep the vehicle speed in such a situation, he/she must put on a servicebrake or downshift.NOTEl If the clutch pedal
(M/T) is depressed, the
Speed Limiter does not activate.If the vehicle speed exceeds the set speed,
control state “LIMIT” and the Speed Limit-
er’s symbol will blink in the combination me-
ter.
If the vehicle speed exceeds the set speed af- ter indicated control state “LIMIT” and the
Speed Limiter’s symbol, beep alert will sound a certain period of time.
While running without blinked control state “LIMIT” and the Speed Limiter’s symbol, if
you decrease the set speed and vehicle speed is more than set speed, control state “LIMIT” and the Speed Limiter’s symbol blinking
starts but beep alert is delayed.
In this case, when vehicle speed keeps ex- ceeding set speed for about 30 seconds after
control state “LIMIT” and the Speed Limit- er’s symbol are blinked, beep alert will sound
a certain period of time.
If the vehicle speeds decreases less than set
speeds, control state “LIMIT” and the Speed Limiter’s symbol stop blinking. When beep
alert is sounding, the beep alert also goes off.NOTEl However, this gives priority to audio and
visual signal of safety reasons or driver’s de-mand.
l If the set speed is too lower based on current
shift position, the Speed Limiter may not
limit the vehicle speed to prevent engine stall.Speed Limiter control switches
E00633301094
There are 4 switches which relate to the
Speed Limiter on the steering wheel.
A-SPEED LIMITER ON/OFF switch
To turn on/off the Speed Limiter.
B-SET - switch
To set the current vehicle speed to a set speed decrease the set speed.
Speed Limiter
6-69OKTE18E1Starting and driving6 Type 1 Type 2

If the set speed reaches to your desired speed,release the SET - switch (B).
The set speed decreases each approximately5 km/h (3 mph).
If a driver wants to decrease the set speed a
little, press SET - switch (B) and release it.
The set speed is decreased 1 km/h each taps.
By using the CANCEL switch,
the service brake and the SET -
switch
E00634201087
Press the CANCEL switch (D) to deactivate
the Speed Limiter.
Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the combination meter.
Decelerate to driver’s desired speed and push
down SET - switch (B) and release.
Speed Limiter
6-73OKTE18E1Starting and driving6Type 1 Type 2 Type 1 Type 2 Type 1

How to operate LDW
E00635801253
The indication changes as follows depending
on the state of the system.
Turning on the system
When you set the ignition switch or operation
mode to “ON”, the LDW system ON indica- tion lamp appears, showing that the system is
placed in the ‘ON state’.
Turning off the system
When you press the LDW switch, the LDW
system ON indication lamp goes out, show-
ing that the system is placed in the ‘OFF state’. Press the switch again, the system re-
turns to “ON”.
Setting of the LDW starting state
You can make the setting of the LDW
ON/OFF state when the ignition switch is turned to the “ON” position or the operation
mode is put in ON as follows.
l LDW 1 (Factory setting): Every time the
LDW will automatically be turned on.
l LDW 2: The LDW ON/OFF state just
before turning the ignition switch to the “LOCK” position or putting the opera- tion mode in OFF is stored.
Setting the LDW mode
1. Press the LDW switch to turn off the
LDW.
2. Press again and hold the LDW switch
for more than 10 seconds.
3. When you release the LDW switch, a
buzzer sounds and the LDW mode will change.
Standby state
In the standby mode, the system is capable of
recognizing the lane in which your vehicle is
positioned and issuing audible warning when your vehicle goes out of the lane.
The system automatically shifts from the ‘ON state’ to the ‘standby state’ if all of the
following conditions are simultaneously met. The LDW system ON indication lamp change to the LDW standby indication lamp
(green).
l The vehicle speed is approximately
65 km/h (40 mph) or higher.
l The turn-signal lever is not operated.
l The hazard lamp is not activated.
l The brake pedal is not depressed.
l Environmental conditions are adequate
for the system to recognize the lanemarkings on both sides.
Lane Departure Warning (LDW)*
6-76OKTE18E1Starting and driving6

Cargo loadsE00609902830
Cargo loads precautionsCAUTIONl When loading luggage, be careful to the fol-
lowing.
• Stow cargo and luggage in the cargo area
whenever possible.
• Distribute cargo or luggage evenly so that
it is not unbalanced.
• Do not place cargo or luggage on the in-
strument panel.
Also, do not stack up cargo or luggage on the front passenger’s seat or the rear seat.
Having the driver’s vision blocked, and
your cargo being thrown inside the cabin if you suddenly have to brake can cause a
serious accident or injury.
Loading a roof carrier
CAUTIONl Use a roof carrier that properly fits your ve-
hicle. Do not load luggage directly onto the
roof.
For installation, refer to the instruction man-
ual accompanying the roof carrier.NOTEl We recommend you to use a
MITSUBISHI
MOTORS GENUINE roof carrier, since the
brackets to be used have a special shape. For details, we recommend you to consult aMITSUBISHI MOTORS Authorized Serv-
ice Point.
Roof carrier precaution
CAUTIONl Make sure that the weight of the luggage
does not exceed the allowable roof load.
If the allowable roof load is exceeded, this may cause damage to the vehicle.
The roof load is the total allowable load on
the roof (the weight of the roof carrier plus
the weight of luggage placed on the roof car- rier).
For the specific value, refer to “Maximum
roof load” on page 11-10CAUTIONl When luggage is loaded onto the vehicle,
please make sure to drive slowly and avoid
excessive manoeuvres such as sudden brak- ing or quick turning.
In addition, place the luggage on the carrier
so that its weight is distributed evenly with the heaviest items on the bottom. Do not load items that are wider than the roof carri-
er.
The additional weight on the roof could raise
the vehicle’s centre of gravity and affect ve-
hicle handling characteristics.
As a result, driving errors or emergency ma- noeuvres could lead to a loss of control and
result in an accident.
l Before driving and after travelling a short
distance, always check the load to make sure
it is securely fastened to the roof carrier.
Check periodically during your travel that the load remains secure.NOTEl To prevent wind noise or reduction in fuel
economy, remove the roof carrier when not
in use.
l Remove the roof carrier before using an au-
tomatic car wash.
Cargo loads
6-83OKTE18E1Starting and driving6