2018 MITSUBISHI L200 key

WARNINGlWhen opening the rear door, confirm that
the occupant of the front seat has taken off the seat belt before opening the rear
door.
If you open the rear door with the front
seat belt being worn, the occupant of the front seat may be tightened with the
locked seat belt and could result in serious injury.
l When closing the rear door, make sure
not being trapped your hands or your fin-
gers in the doors.
l Before driving, make sure that the rear
door is securely closed.
If a door is ajar, the door ajar warning
lamp will illuminates. If a door is not
completely closed, the rear door could open while driving and this could cause
an accident such as occupants being thrown from the vehicle.CAUTIONl When opening or closing the rear door,
please observe the followings. If you do not
follow them, it could result in damage to your vehicle.
• Do not open or close the rear door when
the front door is not completely opened.
• Do not open or close the rear door and the
front door at the same time.
• Do not close the rear door after closing
the front door.Central door locks
E00300803306NOTElRepeated continuous operation between lock
and unlock could activate the central door
locking systems built-in protection circuit
and prevent the system from operating. If
this occurs, wait approximately 1 minute be- fore operating the central door lock system.
All of the doors can be locked and unlocked
as described hereafter.
Driver’s door with key
Using the key on the driver’s door locks or unlocks.
1. Lock
2. Unlock
NOTEl If the vehicle is equipped with the keyless
operation system, the driver’s door can be locked or unlocked with the emergency key.
Refer to “Emergency key” on page 3-11
Driver’s door with inside lock
knob
Using the door lock knob on the driver’s door locks or unlocks all doors.
1. Lock
2. Unlock
NOTEl Be careful not to lock the doors while the
key is inside the vehicle when getting off the vehicle.
Central door locks
3-17OKTE18E1Locking and unlocking3

Vehicle-speed sensitive auto-matic door lock (with impact- sensitive unlock mechanism)
All of the doors lock automatically when the vehicle speed exceeds approximately15 km/h (9 mph) . In addition, all of the doors
unlock when a strong impact that could be
very dangerous to the occupants is sustained by the collision of the vehicle. This is pre-pared for rescue activities when an unexpec-
ted accident occurs.
WARNINGl When the vehicle-speed sensitive automat-
ic door lock/impact-sensitive unlock
mechanism may not operate in the follow- ing conditions, have the vehicle inspected
at a MITSUBISHI MOTORS Authorized
Service Point immediately.
• The door does not lock automatically
even when the vehicle speed exceeds ap-
proximately 15 km/h (9 mph).
• The door unlocks automatically while
driving.
• Even when the ignition switch or the
operation mode is in ON, the SRS
warning lamp does not come on or it
remains on.
• The SRS warning lamp comes on while
driving.
• The central door lock system is broken
down.NOTEl Even if the vehicle suffers significant defor-
mation from a collision etc., depending on the location and angle of the collision, as
well as on the shape and condition of the
other object in the collision, the doors may
not unlock. The extent of deformation or damage to the vehicle does not necessarily correlate with unlocking of the doors.
l These functions are activated when the vehi-
cle is shipped from the factory. If you wish to activate or deactivate these functions,please contact a MITSUBISHI MOTORS
Authorized Service Point.
Unlocking by using the ignition
switch, the engine switch or theselector lever
It is possible to unlock all of the doors when- ever as follows.
[Vehicles with M/T]
The ignition switch is turned to the “LOCK”
position or the operation mode is put in OFF.
[Vehicles with A/T]
The selector lever is placed in the “P” (PARK) position while the operation mode isin ON. Or the operation mode is put in OFF.

These functions are deactivated when the ve-
hicle is shipped from the factory. If you wish
to activate or deactivate these functions,
please contact a MITSUBISHI MOTORS
Authorized Service Point.Dead Lock System*
E00305101209
The Dead Lock System helps prevent theft.
When the keyless entry system or the keyless operation function has been used to lock allof the doors, the Dead Lock System makes it
impossible to unlock the doors using the in- side lock knobs.
CAUTIONl Do not set the Dead Lock System when
someone is inside the vehicle. With the Dead
Lock System set, it is not possible to unlock
the doors using the inside lock knobs. If you erroneously set the Dead Lock System, un-
lock the doors using the UNLOCK switch on the key or using the keyless operation
function.Setting the system
E00305201314
1. Turn the ignition switch to the “LOCK”
position and then remove the key (vehi-
cles with keyless entry system), or put the operation mode in OFF (vehicles
with keyless operation system).
Dead Lock System*
3-18OKTE18E1Locking and unlocking3

2.Get out of the vehicle. Close all of the
doors.
3. Press the LOCK switch (A) on the key,
the driver’s or front passenger’s door lock/unlock switch (C) to lock all of thedoors. The turn-signal lamps will blink
once.
4. Press the switch again within 2 seconds.
The turn-signal lamps will blink three times to show that the Dead Lock Sys- tem has been set.NOTEl Pressing the LOCK switch (A) on the key
once while the Dead Lock System is set cau-ses the turn-signal lamps to blink three
times, so it is possible to confirm that the Dead Lock System is set.Cancelling the system
E00305301458
When the following operation is performed,
the doors will unlock and the Dead Lock Sys- tem will be simultaneously cancelled.
l The UNLOCK switch (B) on the key is
pressed.
l The driver’s or front passenger’s door
lock/unlock switch (C) is pressed while you are carrying the keyless operation
key.
NOTEl If a door is opened within 30 seconds of un-
locking, the doors are automatically relocked
and the Dead Lock System is simultaneously
set again.
l Even when it is not possible to use the key-
less entry system or keyless operation func-
tion to unlock the doors, it is possible to use the key to unlock the driver’s door. When
the key is used to unlock the driver’s door,
the Dead Lock System is cancelled for only the driver’s door. If you wish to subsequent- ly unlock all other doors, turn the ignition
switch to the “ON” or “ACC” position, or put the operation mode in ON or ACC.
l It is possible to adjust the time between
pressing the UNLOCK switch (B) on the key or the driver’s or front passenger’s door
lock/unlock switch (C) and automatic lock-
ing. For details, please contact a MITSUBISHI MOTORS Authorized Serv-
ice Point.
l It is possible to lock the doors and set the
Dead Lock System at the same time with a
single push of the LOCK switch (A) on the key, the driver’s or front passenger’s door
lock/unlock switch (C). For details, please
contact a MITSUBISHI MOTORS Author-
ized Service Point.Testing the system
E00305400159
Open all of the door windows, then set the
Dead Lock System.
(Refer to “Setting the system” on page 3-18.)
Dead Lock System*
3-19OKTE18E1Locking and unlocking3Keyless entry system Keyless operation system

Electric window control switch
E00302303161
Each door window opens or closes while the
corresponding switch is operated.
1- Driver’s door window
2- Front passenger’s door window
3- Rear left door window (Double cab)
4- Rear right door window (Double cab)
5- Lock switch
WARNINGl Before operating the electric window con-
trol, make sure that nothing can get trap-
ped (head, hand, finger, etc.).
l Never leave the vehicle without removing
the key.
l Never leave a child (or other person who
might not be capable of safe operation of the electric window control) in the vehicle alone.WARNINGl The child may tamper with the switch at
the risk of its hands or head being trap-
ped in the window.
Driver’s switches
The driver’s switches can be used to operate
all door windows. A window can be opened or closed by operating the correspondingswitch.
Press the switch down to open the window, and pull up the switch to close it.
If the switch for the driver’s window is fully
pressed down/pulled up, the door window au- tomatically opens/closes completely.
If you want to stop the window movement,
operate the switch lightly in the reverse direc-
tion.
Passenger’s switches
The passenger’s switches can be used to op-
erate the corresponding passenger’s door
windows.
Press the switch down for opening the win-
dow, and pull up the switch for closing it.NOTEl Repeated operation with the engine stopped
will run down the battery. Operate the win-
dow switches only while the engine is run- ning.
l The rear door windows only open halfway.Lock switch
E00303102361
When this switch is operated, the passenger’s
switches cannot be used to open or close the door windows and the driver’s switch cannot
open or close any door windows other than
the driver’s door window.
Electric window control*
3-22OKTE18E1Locking and unlocking3Driver’s switch
LHDDriver’s switch
RHD

Pregnant women restraintE00405600064WARNINGlSeat belts work for everyone, including
pregnant women. Pregnant women should
use the available seat belts. This will re- duce the likelihood of injury to both thewoman and the unborn child. The lap belt
should be worn across the thighs and as snug against the hips as possible, but not
across the waist. Consult your doctor if you have any additional questions or con-
cerns.Seat belt pretensioner
system and force limiter
system* E00405701567
The front seat belts each have a pretensionersystem and force limiter system. (Single caband Club cab)
The front seat belts and the rear outer seat belts each have a pretensioner system and
force limiter system. (Double cab)
Pretensioner system
E00405802464
When the ignition switch or the operation
mode is under the following conditions, if there is a frontal impact or a side impact (ve-
hicles equipped with SRS side airbags and SRS curtain airbags) severe enough to injure
the driver and/or front passenger or when a rollover or overturning of the vehicle is de-
tected (if so equipped), the pretensioner sys- tem will retract the respective seat belts in-
stantaneously, thus maximizing the seat belt’s effectiveness.
[Except for vehicles equipped with keyless operation system]
The ignition switch is in the “ON” or
“START” position.
[Vehicles equipped with keyless operation system]
The operation mode is in ON.
WARNINGl To obtain the best results from your pre-
tensioner seat belt, make sure you have adjusted your seat correctly and wear your seat belt properly.CAUTIONl Installation of audio equipment or repairs in
the vicinity of the pretensioner seat belts or
floor console must be performed in line with MITSUBISHI MOTORS guidelines. It is
important to do so because the work could affect the pretensioner systems.
l If you need to scrap the vehicle, please con-
sult a MITSUBISHI MOTORS Authorized
Service Point. It is important to do so be-
cause unexpected activation of the preten-
sioner seat belts could cause injuries.NOTEl The pretensioner seat belts will be activated
if the vehicle suffers a severe impact, even if the seat belts are not worn.
l The pretensioner seat belts are designed to
work only once. After the pretensioner seat
belts have been activated, we recommend you to have them replaced by a
MITSUBISHI MOTORS Authorized Serv-
ice Point.SRS warning lamp
E00405901413
This warning lamp is shared by the SRS air-
bags and the pretensioner seat belts.
Refer to “SRS warning lamp” on page 4-34.
Pregnant women restraint
4-10OKTE18E1Seat and seat belts4

The SRS curtain airbags (if so equipped) aredesigned to supplement properly worn seat
belts and provide the driver and passengers on the front seat and rear outboard seat with
protection against head injuries by deploying the curtain airbag on the side impacted in
moderate-to-severe side impact collisions.

The SRS is NOT a substitute for the seat belts. To ensure the maximum protection dur-
ing all types of collisions and accidents, all
occupants, including the passengers as well as the driver, must wear their seat belts.NOTEl The ERA-GLONASS (if so equipped) is de-
signed to operate when any of the airbags deploy.
Refer to “ERA-GLONASS*” on page 8-02How the Supplemental Re-
straint System works
E00407303284
The SRS includes the following components:
1. Airbag module (Driver)
2. Front passenger’s airbag indicator (Club
cab and Double cab)
3. Airbag module (Passenger)
4. Driver’s knee airbag module*
5. Front passenger’s airbag ON-OFF
switch (Club cab and Double cab)

6. Side airbag modules*
7. Curtain airbag modules*
Only when the ignition switch or the opera- tion mode is under the following conditions,
the airbags will operate.
[Except for vehicles equipped with keyless
operation system]
The ignition switch is in the “ON” or “START” position.
[Vehicles equipped with keyless operation
system]
The operation mode is in ON.
When the airbag control unit detects a roll- over of the vehicle, the curtain airbags will bedeployed. (if so equipped)
The airbags deployment produces a sudden,
loud noise, and releases some smoke and powder, but these conditions are not injuri-
ous, and do not indicate a fire in the vehicle. People with respiratory problems may feel
some temporary irritation from chemicals used to produce the deployment; open the
windows after airbag deployment, if safe to
do so.
The airbags deflate very rapidly after deploy- ment, so there is little danger of obscured vi-
sion.
Supplemental restraint system (SRS)-airbag*
4-25OKTE18E1Seat and seat belts4

WARNING•Always remove the key from the front
passenger’s airbag ON-OFF switch af-
ter operating that switch. Failure to do so could lead to improper position ofthe front passenger’s airbag ON-OFF
switch.
• Do not turn OFF the front passenger’s
airbag ON-OFF switch except when a child restraint system is fitted to the
front passenger seat.
• If the OFF indicator does not come on
when the front passenger’s airbag ON-
OFF switch is turned OFF, do not fit a child restraint system to the front pas-
senger seat. We recommend you to
have the system inspected by a MITSUBISHI MOTORS Authorized
Service Point.
• If the OFF indicator remains on when
the front passenger’s airbag ON-OFF switch is turned ON, do not allow any- one to sit on the front passenger seat.
We recommend you to have the system inspected by a MITSUBISHI
MOTORS Authorized Service Point.
To turn an airbag off, follow these steps:
1. Insert the key into the front passenger’s
airbag ON-OFF switch, and turn it to the “OFF” position.
2. Remove the key from the front passen-
ger’s airbag ON-OFF switch.
3. Turn the ignition switch to the “ON” po-
sition or put the operation mode in ON. The front passenger’s airbag OFF indi-
cation lamp will stay on.
The front passenger’s airbag is now deactiva- ted and will not deploy until switched on
again.
Driver’s and front passenger’s
airbag system
E00407402015
The driver’s airbag is located under the pad- ded cover in the middle of the steering wheel. The front passenger’s airbag is contained in
the instrument panel above the glove box.
The driver’s airbag inflates at two different rates according to the severity of the impact
(if so equipped).
The driver’s airbag and the front passenger’s
airbag are designed to inflate at the same time even if the passenger seat is not occu-pied.Driver’s knee airbag system*
E00412401263
The driver’s knee airbag is located under the steering wheel. The driver’s knee airbag is
designed to deploy at the same time as the driver’s front airbag.
Supplemental restraint system (SRS)-airbag*
4-28OKTE18E1Seat and seat belts4 AHA109190
Type 1
Type 2

WARNINGlDo not attach accessories to, or put them
in front of, the windscreen. These objects
could restrict the airbag inflation, or strike and injure an occupant if the air-
bags inflate.
l Do not attach additional keys or accesso-
ries (hard, pointed or heavy objects) tothe ignition key. Such objects could pre-
vent the driver’s knee airbag from inflat-
ing normally or could be propelled to
cause serious injury if the airbag inflates.
l Do not attach accessories to the lower
portion of the driver’s side instrumentpanel. Such objects could prevent the
driver’s knee airbag from inflating nor-
mally or could be propelled to cause seri- ous injury if the airbag inflates.WARNINGl Do not put packages, pets or other objects
between the airbags and the driver orfront passenger. It could affect airbagperformance, or could cause injury when the airbag inflates.
l Right after the airbag inflation, several
airbag system components will be hot. Do
not touch these components. There is a danger of being burnt.
l The airbag system is designed to work on-
ly once. Once the airbags have deployed, they will not work again. They must
promptly be replaced and we recommend you to have the entire airbag system in-
spected by a MITSUBISHI MOTORS
Authorized Service Point.Side airbag system*
E00407601892
The side airbags (A) are contained in the
driver and front passenger seatbacks.
The side airbag is designed to inflate only on the side of the vehicle that is impacted, evenwith no passenger in the front seat.
The label shown here is attached to the seat- backs with a side airbag.
Supplemental restraint system (SRS)-airbag*
4-31OKTE18E1Seat and seat belts4