2018 MITSUBISHI L200 warning

Filling the fuel tankE00200204322WARNINGlWhen handling fuel, comply with the safe-
ty regulations displayed by garages and filling stations.
l Fuel is highly flammable and explosive.
You could be burned or seriously injured
when handling it. When refueling your
vehicle, always turn the engine off and keep away from flames, sparks and smok-
ing materials. Always handle fuel in well-
ventilated outdoor areas.
l Before removing the fuel cap, be sure to
get rid of your body’s static electricity by touching a metal part of the vehicle or
fuel pump. Any static electricity on your
body could create a spark that ignites fuel vapour.
l Perform the whole refueling process
(opening the fuel tank filler door, remov-
ing the fuel cap, etc.) by yourself. Do not let any other person come near the fuel
tank filler. If you allowed a person to help you and that person was carrying static electricity, fuel vapour could be ignited.
l Do not move away from the fuel tank fill-
er until refueling is finished. If you moved
away and did something else (for exam- ple, sitting on a seat) part-way through
the refueling process, you could pick up a fresh charge of static electricity.
l Be careful not to inhale fuel vapour. Fuel
contains toxic substances.WARNINGl Keep the doors and windows closed while
refueling the vehicle. If they were open,fuel vapour could get into the cabin.
l If the fuel cap must be replaced, use only
a MITSUBISHI MOTORS genuine part.
Fuel tank capacity
75 litres
Refueling
1. Before filling with fuel, stop the engine.
2. The fuel tank filler is located on the rear
left side of your vehicle.
Open the fuel tank filler door with the
release lever located below the instru- ment panel. (Only vehicles for Type 1,
2)
3. [Vehicles for Type 1, 2] Open the fuel tank filler tube by slowly
turning the fuel cap anticlockwise.
Filling the fuel tank
2-03OKTE18E1General information2 Type 1 Type 2 Type 1

Entering or leaving the
vehicle E00205800022CAUTIONlTo avoid slipping and damaging the painted
surface, do not step on the cover of the side
step (A).Installation of accessories
E00200302606
We recommend you to consult yourMITSUBISHI MOTORS Authorized Service
Point.
CAUTIONl Your vehicle is equipped with a diagnosis
connector for checking and servicing theelectronic control system.
Do not connect a device other than a diagno-
sis tool for inspections and service to this
connector.
Otherwise, the battery could be discharged,
the electronic devices of the vehicle could malfunction, or other unexpected problems could result.
In addition, malfunctions caused by connect-
ing a device other than a diagnosis tool may not be covered under warranty.
l The installation of accessories, optional
parts, etc., should only be carried out
within the limits prescribed by law in your country, and in accordance with the
guidelines and warnings contained with-
in the documents accompanying this ve- hicle.
l Improper installation of electrical parts
could cause fire, please refer to the Mod-
ification/ alteration to the electrical or fuel systems section within this owner’smanual.
l When installing the radio, for the re-
quired information (frequency, transmis-
sion output, installing procedure), con-
sult a MITSUBISHI MOTORS Author-
ized Service Point.
If the frequency, transmission output and
installing condition are not appropriate, it can adversely affect the electronic de-vices and could lead to unsafe vehicle
operation.
l Using a cellular phone or radio set inside
the vehicle without an external antenna
may cause electrical system interference,
which could lead to unsafe vehicle oper- ation.
l Tyres and wheels which do not meet
specifications must not be used.
Refer to the “Specifications” section for information regarding wheel and tyre
sizes.
Important points!
Due to a large number of accessories and re-
placement parts of different manufactures available in the market, it is not possible, not
only for MITSUBISHI MOTORS , but also
for a MITSUBISHI MOTORS Authorized
Service Point, to check whether the attach- ment or installation of such parts affects the
overall safety of your vehicle.

Entering or leaving the vehicle
2-05OKTE18E1General information2

Even when such parts are officially Author-ized, for example by a “general operators
permit” (an appraisal for the part) or through the execution of the part in an officially ap- proved manner of construction, or when a
single operation permit following the attach- ment or installation of such parts, it cannot be
deduced from that alone, that the driving safety of your vehicles has not been affected.

Consider also that there basically exists no li- ability on the part of the appraiser or the offi-
cial. Maximum safety can only be ensured
with parts recommended, sold and fitted or installed by a MITSUBISHI MOTORS Au-
thorized Service Point ( MITSUBISHI
MOTORS GENUINE replacement parts and
MITSUBISHI MOTORS accessories). The
same also pertains to modifications of vehi- cles with respect to the production specifica- tions. For safety reasons, do not attempt any
modifications other than those that follow the recommendations of a MITSUBISHI
MOTORS Authorized Service Point.Modification/alterations to
the electrical or fuel systems E00200401525
MITSUBISHI MOTORS has always manu-
factured safe, high quality vehicles. In order to maintain this safety and quality, it is im-
portant that any accessory that is to be fitted, or any modifications carried out which in-
volve the electrical or fuel systems, should be carried out in accordance with MITSUBISHI
MOTORS guidelines.CAUTIONl If the wires interferes with the vehicle body
or improper installation methods are used (protective fuses not included, etc.), elec-
tronic devices may be adversely affected, re-
sulting in a fire or other accident.Genuine parts
E00200501715
MITSUBISHI MOTORS has gone to great
lengths to bring you a superbly crafted vehi-
cle offering the highest quality and dependa- bility.
Use MITSUBISHI MOTORS GENUINE
Parts, designed and manufactured to maintain your MITSUBISHI MOTORS vehicle at top
performance. MITSUBISHI MOTORS GEN- UINE Parts are identified by this mark and
are available at all MITSUBISHI MOTORS
Authorized Service Points.Safety and disposal
information for used engine
oil E00200601426WARNINGlProlonged and repeated contact may
cause serious skin disorders, including
dermatitis and cancer.
l Avoid contact with the skin as far as pos-
sible and wash thoroughly after any con- tact.
l Keep used engine oils out of reach of chil-
dren.
Modification/alterations to the electrical or fuel systems
2-06OKTE18E1General information2

KeysE00300104319
1. Master key
2. Keyless entry key
3. Keyless operation key
4. Emergency key
WARNINGl When taking a key on flights, do not press
any switches on the key while on the plane. If a switch is pressed on the plane,the key emits electromagnetic waves,which could adversely affect the plane’s
flight operation.
When carrying a key in a bag, be careful that no switches on the key can be easily
pressed by mistake.NOTEl The key is a precision electronic device with
a built-in signal transmitter. Please observe
the following in order to prevent a malfunc- tion.
• Do not leave in a place that is exposed to
direct sunlight, for example on the dash- board.
• Do not disassemble or modify.
• Do not excessively bend the key or sub-
ject it to strong impacts.
• Do not expose to water.
• Keep away from magnetic key rings.
• Keep away from audio systems, personal
computers, TVs, and other equipment that generates a magnetic field.
• Keep away from devices that emit strong
electromagnetic waves, such as cellular phones, wireless devices and high fre-
quency equipment (including medical de- vices).NOTE• Do not clean with ultrasonic cleaners or
similar equipment.
• Do not leave the key where it may be ex-
posed to high temperature or high humidi-
ty.
l The engine is designed so that it will not
start if the ID code registered in the immo-
bilizer computer and the key’s ID code do
not match. Refer to the “Electronic immobil- izer” section for details and key usage.
l If you lose one of them, contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point as soon as possible to prevent theft.Key number tag
E00312701092
The key number is stamped on the tag as in-
dicated in the illustration.
Keys
3-02OKTE18E1Locking and unlocking3Key Keyless operation keyKeyless entry key

NOTE•The key switch is operated at the correct
distance from the vehicle, but the doorsare not locked/unlocked in response.
• The indication lamp (3) is dim or does not
come on.

For further information, please contact a MITSUBISHI MOTORS Authorized
Service Point.
If you replace the battery yourself, refer to
“Procedure for replacing the key battery” on page 3-06.
l If your key is lost or damaged, please con-
tact a MITSUBISHI MOTORS Authorized
Service Point for a replacement key.
l If you wish to add key, please contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
The following numbers of the keys are avail- able.
• Keyless entry key: up to 4 keys.
• Keyless operation key: up to 4 keys.Procedure for replacing the
key battery
E00309501849
Before replacing the battery, remove static
electricity from your body by touching a met- al grounded object.
WARNINGl Danger of explosion if battery is incor-
rectly replaced.
Replace only with the same battery or an equivalent type.CAUTIONl When the key case is opened, be careful to
keep water, dust, etc. out. Also, do not touch
the internal components.NOTEl You may purchase a replacement battery at
an electric appliance store.
l A
MITSUBISHI MOTORS Authorized
Service Point can replace the battery for you
if you prefer.
1. Remove the screw (A) from the key.
(Keyless entry key only)
2. Remove the emergency key from the
key. (Keyless operation key only)
Refer to “Emergency key” on page
3-11.
3. With the MITSUBISHI mark facing
you, insert the cloth-covered tip of a
straight blade (or minus) screwdriver in-
to the notch in the key case and use it to open the case.
Keyless entry system*
3-06OKTE18E1Locking and unlocking3 Keyless entry key Keyless entry key Keyless operation key

NOTElBe sure to perform the procedure with the
MITSUBISHI mark facing you. If the
MITSUBISHI mark is not facing you when
you open the key case, the switches may
come out.
4. Remove the old battery.
5. Install a new battery with the + side (B)
up.
6. Close the key case firmly.
7. Attach the screw (A) removed in step 1.
(Keyless entry key only)
8. Install the emergency key removed in
step 2. (Keyless operation key only)
9. Check the keyless entry system to see
that it works.Keyless operation system*
E00305602230
The keyless operation system allows you tolock and unlock the doors, start the engine
and change the operation mode simply by
carrying the keyless operation key with you. The switches on the keyless operation key can also be used as the key switch of keyless
entry system.
Refer to “Starting and stopping the engine” on page 6-18.
Refer to “Keyless entry system*” on page 3-04.

The driver should always carry the keyless operation key. This key is necessary for lock- ing and unlocking the doors, starting the en-
gine and otherwise operating the vehicle, so before locking and leaving the vehicle, be
sure to check that you have the keyless oper- ation key.
WARNINGl People with implantable cardiac pace-
makers or implantable cardiovascular-de- fibrillators should not go near the exterior
transmitters (A) or the interior transmit-
ters (B). The radio waves used by the key-
less operation system could adversely af- fect implantable cardiac pacemakers orimplantable cardiovascular-defibrillators.
Keyless operation system*
3-07OKTE18E1Locking and unlocking3 Keyless entry key+ side - side
Coin type battery CR1620 Keyless operation key+ side - side
Coin type battery CR2032 Club cab

WARNINGlWhen using electro-medical devices other
than implantable cardiac pacemakers or implantable cardiovascular-defibrillators,
contact the electro-medical device manu- facturer ahead of time to determine theaffects of radio waves on the devices. Elec-
tro-medical device operations could be af- fected by radio waves.
You can limit the possible operations of the
keyless operation system in the following ways. (The keyless operation system can be
used as a keyless entry system.) Please con-
sult a MITSUBISHI MOTORS Authorized
Service Point.
l You can limit operations to locking and
unlocking the doors.
l You can limit operations to starting the
engine.
l The keyless operation system can be dis-
abled.
When keyless operation system operations are modified, the operating transmitters are as
follows.
l Only locking and unlocking doors: exte-
rior transmitter and interior transmitter
l Only starting the engine: interior trans-
mitterNOTEl The keyless operation key uses an ultra-
weak electromagnetic wave. In the following
cases, the keyless operation system may not
operate properly or may be unstable.
• When there is equipment nearby that
emits strong radio waves, such as: a pow-
er station, a radio/TV broadcasting station or an airport.
• The keyless operation system is carried
together with a communications device such as a cellular phone or radio set, or
with an electronic device such as a per- sonal computer.
• The keyless operation key is touching or
covered by a metal object.
• A keyless entry system is being used
nearby.
• When the keyless operation key battery is
worn out.NOTE• When the keyless operation key is placed
in an area with strong radio waves or noise.
In such cases, use the emergency key.
Refer to “To lock/unlock without using
the keyless operation function” on page 3-11.
l Because the keyless operation key receives
signals in order to communicate with the transmitters in the vehicle, the battery con-tinually wears down regardless of keylessoperation key use. The battery life is 1 to 2
years, depending on usage conditions. When the battery wears out, replace the battery ac-cording to the description in this manual or
have it replaced a MITSUBISHI MOTORS
Authorized Service Point.
Refer to “Procedure for replacing the key battery” on page 3-06.
l Because the keyless operation key continual-
ly receives signals, strong radio wave recep- tion could affect battery wear. Do not leave
the key near a TV, personal computer, or
other electronic device.Operating range of the keyless
operation system
E00305701609
If you are carrying the keyless operation key, enter the operating range of the keyless oper-ation system, and press the driver’s or front
passenger’s door lock/unlock switch, the ID
code for your key is verified.
Keyless operation system*
3-08OKTE18E1Locking and unlocking3Double cab

Warning activation
E00305902031
In order to prevent vehicle theft or the accidental operation of the keyless operation system, the lamp and buzzer are used to alert the driver.
LampBuzzerItemCauseNote (Solution)Blinks.Outer buzzer sounds
4 times. Inner buzzer
sounds.Keyless operation key
take-out monitoring systemWhen the vehicle is parked with the opera- tion mode in any mode other than OFF, if you close the door after opening any of the
doors and taking the keyless operation key out of the vehicle.
Outer buzzer sounds 4 times at this time.
And when a vehicle starts, inner buzzer
sounds once.l If you take the keyless opera-
tion key out of the vehiclethrough a window without
opening a door, this system does not operate.
l It is possible to change the set-
ting to make the system operate
if you take the keyless opera-
tion key out from the vehicle through a window without
opening a door. For further in- formation, please contact a MITSUBISHI MOTORS Au-
thorized Service Point.
l Even if you have the keyless
operation key within the engine start operating range, if the keyand vehicle ID codes cannot be
matched, for example due to the ambient environment or electromagnetic conditions, the
warning may be activated.
Keyless operation system*
3-12OKTE18E1Locking and unlocking3