2018 MITSUBISHI ECLIPSE CROSS ignition

Blind Spot Warning (BSW) (with Lane
Change Assist) (if so equipped)
5-110 Features and controls
5
ON and “ON” is selected in the “BSW” set- ting screen, the BSW indicator light in the instrument cluster comes on and the BSW enters the standby state.When “OFF” is selected in the “BSW” set- ting screen, the BSW indicator light in the instrument cluster goes off and the BSWturns off. To turn the BSW ON/OFF, follow the proce- dure below. 1. Switch to the function setting screen. Refer to “Multi-information displayswitches” on page 5-142. Refer to “Changing the function settings” on page 5-152. 2. Press the switch or switch several times to switch to the “BSW” screen. Then, press the switch to the setting selection screen. 3. Press the switch or switch to select “ON” or “OFF”, and then press the
switch to confirm the setting.
Indicator light
If you turn the BSW ON/
OFF, the Rear Cross
Traffic Alert (RCTA) also turns ON/OFF at the same time.
When the BSW indicator light in the instru- ment cluster is on, if a vehicle is approaching your vehicle in the detection area, the Blind Spot Warning light in the outside rearviewmirror illuminates. If the turn signal lever is operated to the side where the Blind Spot Warning light is illumi-nated, the Blind Spot Warning light will blinkand the system will beep three times to alert the driver.
NOTE
 When the operation mode is set to OFF, the selected condition just before setting to OFFis retained.  The BSW operates when all of the following conditions are met. • The ignition switch is turned to the “ON” position or the operation mode is put in ON. • The selector lever is in positions other than “P” (PARK) and “R” (REVERSE). • The speed of your vehicle is approximately 6 mph (10 km/h) or higher.
When the sensor detects an approaching vehicle

NOTE
 The Blind Spot Warning light in the outside rearview mirror may come on or blink in the following conditions. • When driving very near the guardrail or the concrete wall.
BK0252700US.book
110 ページ ２０１７年１０月４日　水曜日　午後４時５４分

Lane Departure Warning (LDW) (if so equipped)Features and controls 5-115
5
Frequency bands: 24.05 - 24.25 GHz
Output power: less than 20 milliwatts
N00577900062
The Lane Departure Warning (LDW) is a
driving aid system to help prevent uninten-
tional lane departure. The LDW is designed
to read lane markers by using a sensor (A)
under certain conditions. The LDW will give
you both visual and audible warnings when
your vehicle is leaving or has left the lane.
N00578000057
To turn on the LDW, press the LDW switch.
The indicator (white) will appear on the
information screen of the multi-information
display.
To turn off the LDW, press the LDW switch.
The indicator on the information screen of
the multi-information display will then go
out.
To return the LDW to “ON”, press the LDW
switch again.
(1) This device may not cause interference,
and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Lane Departure Warning
(LDW)
(if so equipped)
WA R N I N GNever rely solely on the LDW. The LDW is
not a collision avoidance system and is not
a substitute for your safe and careful driv-
ing.Before using the LDW, read this entire
section to understand the limitations of
this system. Failure to follow instructions
could result in an accident.To turn on/off the LDW

NOTE
The LDW is turned on when the vehicle is
shipped from the factory.
 The currently selected LDW setting (on or
off) is stored even when the ignition switch
is turned to the “OFF” position or the opera-
tion mode is put in OFF.
BK0252700US.book 115 ページ ２０１７年１０月１２日　木曜日　午後１時２分

Tire pressure monitoring system (TPMS)
Features and controls 5-119
5
N00532701389
When the ignition switch is turned to the “ON” position or the operation mode is put inON, the tire pressure monitoring system
warning light normally illuminates and goes off a few seconds later. If one or more of the vehicle tires (except for the spare tire) is significantly under-inflated, the warning light will remain illuminatedwhile the ignition switch is in the “ON” posi- tion or the operation mode is put in ON. Refer to “If the warning light / display illumi-nates while driving” on page 5-120 and take the necessary measures.
For details, please contact your authorized Mitsubishi Motors dealer.
Tire pressure monitoring sys- tem warning light / display
NOTE
Type 1Type 2
NOTE
 In addition, the warning display is displayed on the information screen in the multi-infor- mation display.
CAUTION If the tire pressure monitoring system warn- ing light does not illuminate when the igni- tion switch is turned to the “ON” position or the operation mode is put in ON, it means that the tire pressure monitoring system isnot working properly. Have the system inspected by an authorized Mitsubishi Motors dealer.In such situations,
a malfunctioning of the
system may be preventing the monitoring of the tire pressure. Avoid sudden braking,sharp turning and high-speed driving. If a malfunction is detected in the tire pres- sure monitoring system, the tire pressure monitoring system warning light will blink for approximately 1 minute and then remaincontinuously illuminated. The warning light will issue further warn
ings each time the
engine is restarted as long as the malfunctionexists. Check to see whether the warning light goes off after few minutes driving.If it then goes off during driving, there is no problem. However, if the warning light does not gooff, or if it blinks again when the engine is restarted, have the vehicle inspected by an authorized Mitsubishi Motors dealer. In such situations,
a malfunctioning of the
system may be preventing the monitoring ofthe tire pressure. For safety reasons, when the warning light appears while driving, avoid sudden braking, sharp turning andhigh-speed driving.
BK0252700US.book
119 ページ ２０１７年１０月４日　水曜日　午後４時５４分

Rear-view camera
Features and controls 5-127
5
N00590200046
If the system detects a problem with a sensor, a warning is displayed in the multi-informa- tion display and a buzzer will sound forapproximately five seconds.
Also, the indicator light (A) on the “SONAR” switch will continue blinking until the sensor resumes functioning. Have the vehicle inspected at an authorizedMitsubishi Motors dealer or a repair facility of your choice.
N00546201330
When the selector lever is in the “R” (REVERSE) position with the ignition switch in the “ON” position, or the operation mode is put in ON, the rear-view image will be dis-played on the screen of the Smartphone Link Display Audio. When the selector lever is shifted out of the“R” (REVERSE) position, the rear-view image will go off.
The rear-view camera (A) is in the liftgate, at the left side of the liftgate handle.
NOTE
 The detection mode will not change if you keep the “SONAR” switch pressed for 10 seconds or more.  In the normal mode, even after the “SONAR” switch has been pressed to turn off the parking sensors, the two rear center sensors will continue functioning while theselector lever is in the “R” (REVERSE) posi- tion.
When a problem is detected

Example: Rear corner sensor (left) malfunction- ing
Rear-view camera
WA R N I N G Never rely solely on the rear-view camera to clear the area behind your vehicle. Always check visually behind and all around your vehicle for persons, animals, obstructions or other vehicles. Failure todo so can result in vehicle damage, serious injury or death. The rear-view camera is an aid system for backing up, but it is not a substitute for your visual confirmation. The view on the screen is limited, and objects outside the view, such as under thebumper or around either corner of the bumper end, cannot be seen on the screen.
Location of rear-view camera
BK0252700US.book
127 ページ ２０１７年１０月４日　水曜日　午後４時５４分

Multi-information display 5-140 Features and controls
5
N00519201303
The tachometer shows engine revolutions per minute. This allows the driver to determinethe most efficient selector position and engine speed combinations. This gauge also assist
s in evaluating engine
performance.
N00554901293
Each time you press this button, there is asound and the brightness of the instrumentschanges.
N00555001419
The multi-information display displays warn- ings, the odometer, trip odometer, service reminder, engine coolant temperature, fuelremaining, outside temperature, selector lever position, average and instant fuel consump- tion, driving range, average speed, etc. It is also possible to change elements such as the language and units used on the multi- information display.
Tachometer
CAUTION The red zone indicates an engine speed beyond the range of safe operation. Select the correct selector position to control the engine speed so that the tachometer indi- cator does not enter the red zone.
Meter illumination control 1- Brightness level 2- Rheostat illumination button
NOTE
 You can adjust to 8 different levels for when the front side-marker lights are illuminatedand when they are not.  If the vehicle is equipped with the automatic light control, the light switch is in a position other than the “OFF” position and it is suffi- ciently dark outside the vehicle, the meterillumination switches automatically to the adjusted brightness.
 The brightness level of the instruments is stored when the ignition switch is turned to the “OFF” position or the operation mode is put in OFF.  If you press and hold the button for longer than approximately 2 second when the front side-marker lights are illuminated, thebrightness level changes to the maximum level. Pressing and holding the button for longer than approximately 2 second againreturns the brightness level to the previous level. On vehicles equipped with Smartphone LinkDisplay Audio, the map screen color may not be switched to nighttime setting when the meter illumination brightness level is at themaximum.
Multi-information display
NOTE
BK0252700US.book
140 ページ ２０１７年１０月４日　水曜日　午後４時５４分

Multi-information display
Features and controls 5-141
5
[With ignition switch or operation mode in OFF] 1-
Warning display screen
 P.5-146
2- Information screen
 P.5-143
Interrupt display screen
 P.5-146
3- Door ajar warning display screen
 P.5-147
4- Odometer
 P.5-148
5-
“ ” mark indicator
 P.5-146
BK0252700US.book
141 ページ ２０１７年１０月４日　水曜日　午後４時５４分

Multi-information display 5-142 Features and controls
5
[With ignition switch or operation mode in ON]
N00555101234
Each time the multi-information display switches are operated, the buzzer sounds andthe multi-information display changes
1- S-AWC drive mode display screen (if
so equipped)
 P.5-69
2-
Warning display screen
 P.5-146
3- Lane Departure Warning (LDW) dis-
play screen (if so equipped)
P.5-115
4- ECO mode indicator display screen
 P.5-198
5- Information screen
 P.5-143
6- Selector lever position display
 P.5-63
7- Engine coolant temperature display
 P.5-147
8- Odometer
 P.5-148
9- Cruise control display screen
 P.5-84
10- Adaptive Cruise Control System (ACC)
display screen (if so equipped)  P.5-88
11- ECO indicator
 P.5-151
12-
“ ” mark indicator
 P.5-146
13- Fuel remaining display screen
 P.5-147
14- Outside temperature display screen
 P.5-148
NOTE
The fuel units, outside temperature units, display language, and other settings can be changed. Refer to “Changing the function settings” on page 5-152.
Multi-information display switches
BK0252700US.book
142 ページ ２０１７年１０月４日　水曜日　午後４時５４分

Multi-information display
Features and controls 5-143
5
between information such as warnings, trip odometer, average and instant fuel consump- tion, distance range. It is also possible to
change elements such as
the language and units used on the multi- information display by operating the multi- information display switches.
N00555301207
Press the switch to display the information screen. Then, press the switch or switch to switch the display screen in the fol
lowing order.
Information screen (With the ignition switch in “OFF” position or the operation mode in OFF) *: When there is a warning display 1-
Trip odometer
 P.5-148
BK0252700US.book
143 ページ ２０１７年１０月４日　水曜日　午後４時５４分